| 1. |
- Lundberg, Mattias, 1985-
(author)
-
Residual stresses, fatigue and deformation in cast iron
- 2018
-
Doctoral thesis (other academic/artistic)abstract
- The complex geometry of cylinder heads in heavy-duty diesel engines makes grey iron or compact graphite iron a preferred material choice due to its price, castability, thermal conductivity and damping capacity. Today’s strict emission laws have increased the demands on engine performance and engine efficiency. This means that material properties such as fatigue resistance need to be improved. Shot peening is often used to improve the fatigue resistance of components and the benefits of shot peening are associated with the induced compressive surface stresses and surface hardening. How different shot peening parameters can affect fatigue strength of grey and compact graphite iron has been investigated within the project underlying this thesis. To do this, X-ray diffraction (XRD) was utilized for residual stress measurements, scanning electron microscopy (SEM) for microstructural characterizations and mechanical fatigue testing for mechanical quantifications. The ultimate aim of this work has been to increase the fatigue resistance of cast iron by residual stress optimization.XRD measurements and SEM examinations revealed that the shot peening parameters shot size and peening intensity significantly influence residual stresses and surface deformation. Residual stress profiles, similar to the one general considered to improve the fatigue strength in steels, were obtained for both grey and compact graphite iron. Uniaxial push-pull fatigue testing on grey iron with these shot peening parameters reduced the fatigue strength with 15–20 %. The negative effect is likely related to surface damage associated with over peening and relatively high subsurface tensile residual stresses. With very gentle shot peening parameters, the uniaxial fatigue strength were unaltered from the base material but when subjected to bending fatigue an increase in fatigue strength were observed. An alternative way to increase the fatigue strength was to conduct a 30 min annealing heat treatment at 285 XC which increased the fatigue strength by almost 10 % in uniaxial loading. The improvement could be an effect of favourable precipitates forming during the annealing, which could hinder dislocation movement during fatigue.Measuring residual stresses using XRD and the sin2 -method demands accurate X-ray elastic constants (XEC) for meticulous stress analysis. The XEC referred to as 1~2s2 should therefore always be calibrated for the specific material used. The experiments conducted revealed that the XEC value is independent of the testing method used in this work. A small correction from the theoretical value should be applied when the material contains small amounts of residual stresses. The amount of residual stresses has a great impact on the XEC and thus on the stress analysis. Concluding that proper analysis of residual stresses in cast iron is not straight forward.
|
|
| 2. |
- Lundberg, Mattias, et al.
(author)
-
Surface Integrity and Fatigue Behaviour of Electric Discharged Machined and Milled Austenitic Stainless Steel
- 2017
-
In: Materials Characterization. - : Elsevier. - 1044-5803 .- 1873-4189. ; 124, s. 215-222
-
Journal article (peer-reviewed)abstract
- Machining of austenitic stainless steels can result in different surface integrities and different machining process parameters will have a great impact on the component fatigue life. Understanding how machining processes affect the cyclic behaviour and microstructure are of outmost importance in order to improve existing and new life estimation models. Milling and electrical discharge machining (EDM) have been used to manufacture rectangular four-point bend fatigue test samples; subjected to high cycle fatigue. Before fatigue testing, surface integrity characterisation of the two surface conditions was conducted using scanning electron microscopy, surface roughness, residual stress profiles, and hardness profiles. Differences in cyclic behaviour were observed between the two surface conditions by the fatigue testing. The milled samples exhibited a fatigue limit. EDM samples did not show the same behaviour due to ratcheting. Recrystallized nano sized grains were identified at the severely plastically deformed surface of the milled samples. Large amounts of bent mechanical twins were observed ~ 5 μm below the surface. Grain shearing and subsequent grain rotation from milling bent the mechanical twins. EDM samples showed much less plastic deformation at the surface. Surface tensile residual stresses of ~ 500 MPa and ~ 200 MPa for the milled and EDM samples respectively were measured.
|
|
| 3. |
- Azeez, Ahmed, et al.
(author)
-
Characterisation of Deformation and Damage in a Steam Turbine Steel Subjected to Low Cycle Fatigue
- 2019
-
In: Structural Integrity Procedia. - : Elsevier BV. ; , s. 155-160
-
Conference paper (peer-reviewed)abstract
- The increased use of renewable energy pushes steam turbines toward a more frequent operation schedule. Consequently, components must endure more severe fatigue loads which, in turn, requires an understanding of the deformation and damage mechanisms under high-temperature cyclic loading. Based on this, low cycle fatigue tests were performed on a creep resistant steel, FB2, used in ultra-supercritical steam turbines. The fatigue tests were performed in strain control with 0.8-1.2 % strain range and at temperatures of 400 °C and 600 °C. The tests at 600 °C were run with and without dwell time. The deformation mechanisms at different temperatures and strain ranges were characterised by scanning electron microscopy and by quantifying the amount of low angle grain boundaries. The quantification of low angle grain boundaries was done by electron backscatter diffraction. Microscopy revealed that specimens subjected to 600 °C showed signs of creep damage, in the form of voids close to fracture surface, regardless of whether the specimen had been exposed to dwell time or been purely cycled. In addition, the amount of low angle grain boundaries was lower at 600 °C than at 400 °C. The study indicates that a significant amount of the inelastic strain comes from creep strain as opposed to being all plastic strain.
|
|
| 4. |
- Azeez, Ahmed, et al.
(author)
-
Low Cycle Fatigue Modelling of Steam Turbine Rotor Steel
- 2019
-
In: 9th International Conference Materials Structure & Micromechanics of Fracture (MSMF9). - : Elsevier. ; , s. 149-154, s. 149-154
-
Conference paper (peer-reviewed)abstract
- Materials in steam turbine rotors are subjected to cyclic loads at high temperature, causing cracks to initiate and grow. To allow for more flexible operation, accurate fatigue models for life prediction must not be overly conservative. In this study, fully reversed low cycle fatigue tests were performed on a turbine rotor steel called FB2. The tests were done isothermally, within temperature range of room temperature to 600 °C, under strain control with 0.8-1.2 % total strain range. Some tests included hold time to calibrate the short-time creep behaviour of the material. Different fatigue life models were constructed. The life curve in terms of stress amplitude was found unusable at 600 °C, while the life curve in terms of total strain or inelastic strain amplitudes displayed inconsistent behaviour at 500 °C. To construct better life model, the inelastic strain amplitudes were separated into plastic and creep components by modelling the deformation behaviour of the material, including creep. Based on strain range partitioning approach, the fatigue life depends on different damage mechanisms at different strain ranges. This allowed the formulation of life curves based on plasticity or creep domination, which showed creep domination at 600 °C, while at 500 °C, creep only dominates for higher strain range.
|
|
| 5. |
|
|
| 6. |
- Calmunger, Mattias, et al.
(author)
-
Characterisation of creep deformation during slow strain rate tensile testing
- 2015
-
Other publication (other academic/artistic)abstract
- The strain-rate dependent deformation of the superalloy Haynes 282 during slow strain-rate tensile testing (SSRT) at 700 C has been investigated. The stress-strain response is remarkably well described by a simple constitutive model over a wide range of different strain-rates. The microstructure development is characterised and related to the influence of both strainrate dependent and independent deformation. Damage and cracking similar to what has been observed previously during conventional creep testing of Haynes 282 was found and explained. The model and the microstructure investigations show that the deformation and damage mechanisms during SSRT are essentially the same as under creep.
|
|
| 7. |
- Calmunger, Mattias, et al.
(author)
-
Characterization of austenitic stainless steels deformed at elevated temperature
- 2017
-
In: Metallurgical and Materials Transactions. A. - : Springer-Verlag New York. - 1073-5623 .- 1543-1940. ; 48A:10, s. 4525-4538
-
Journal article (peer-reviewed)abstract
- Highly alloyed austenitic stainless steels are promising candidates to replace more expansive nickel-based alloys within the energy-producing industry. The present study investigates the deformation mechanisms by microstructural characterisation, mechanical properties and stress-strain response of three commercial austenitic stainless steels and two commercial nickel-based alloys using uniaxial tensile tests at elevated temperatures from 400 C up to 700 C. The materials showed different influence of temperature on ductility, where the ductility at elevated temperatures increased with increasing nickel and solid solution hardening element content. The investigated materials showed planar dislocation driven deformation at elevated temperature. Scanning electron microscopy showed that deformation twins were an active deformation mechanism in austenitic stainless steels during tensile deformation at elevated temperatures up to 700 C.
|
|
| 8. |
- Calmunger, Mattias, et al.
(author)
-
Creep and Fatigue Interaction Behavior in Sanicro 25 Heat Resistant Austenitic Stainless Steel
- 2016
-
In: Transactions of the Indian Institute of Metals. - : Springer. - 0972-2815 .- 0975-1645. ; 69:2, s. 337-342
-
Journal article (peer-reviewed)abstract
- Sanicro 25 is a newly developed advanced high strength heat resistant austenitic stainless steel. The material shows good resistance to steam oxidation and flue gas corrosion, and has higher creep rupture strength than other austenitic stainless steels available today. It is thus an excellent candidate for superheaters and reheaters for advanced ultra-super critical power plants with efficiency higher than 50 %. This paper provides a study on the creep–fatigue interaction behavior of Sanicro 25 at 700 °C. Two strain ranges, 1 and 2 %, and two dwell times, 10 and 30 min, were used. The influences of dwell time on the cyclic deformation behavior and life has been evaluated. Due to stress relaxation the dwell time causes a larger plastic strain range compared to the tests without dwell time. The results also show that the dwell time leads to a shorter fatigue life for the lower strain range, but has no or small effect on the life for the higher strain range. Fracture investigations show that dwell times result in more intergranular cracking. With the use of the electron channeling contrast imaging technique, the influences of dwell time on the cyclic plastic deformation, precipitation behavior, recovery phenomena and local plasticity exhaustion have also been studied.
|
|
| 9. |
|
|
| 10. |
|
|
