| 1. |
- Laux, M., et al.
(author)
-
Arcing at B4C-covered limiters exposed to a SOL-plasma
- 2003
-
In: Journal of Nuclear Materials. - 0022-3115 .- 1873-4820. ; 313, s. 62-66
-
Journal article (peer-reviewed)abstract
- Plasma sprayed B4C-layers considered as wall coatings for the W7X stellarator have been studied during and after exposure to TEXTOR and after arcing experiments in vacuum. Arcing through the B4C layer occurred favoured by high power fluxes and not restricted to less stable phases. But this arcing implies an especially noisy scrape-off layer (SOL). Instead of moving retrograde in the external magnetic field, the arc spot on the B4C-layer sticks to the same location for its whole lifetime. Consequently, the arc erodes the entire B4C layer, finally burning down to the Cu substrate. In the neighbourhood of craters the surface contains Cu originating from those craters. This material, hauled to the surface by the arc, is subject to subsequent erosion, transport, and redeposition by the SOL-plasma. The behaviour of arcs on B4C is Most probably caused by the peculiar temperature dependences of the electrical and heat conductivity of B4C.
|
|
| 2. |
- Pospieszczyk, A., et al.
(author)
-
B4C-limiter experiments at TEXTOR
- 2003
-
In: Journal of Nuclear Materials. - 0022-3115 .- 1873-4820. ; 313, s. 223-229
-
Journal article (peer-reviewed)abstract
- In the TEXTOR tokamak the five top and five bottom poloidal carbon limiter blocks have been replaced by inertially cooled copper blocks coated with a 170 mum VPS-B4C layer. Similar limiter blocks have been inserted through lock systems, extensively diagnosed in situ as well as ex situ. During the thermal load by the plasma, the surface temperature rose and decayed extremely fast which can be explained by a different thermal conductivity and heat capacity of the coating. For heat loads below 8 MW m(-2) no severe cracking or delamination of the B4C-coating were observed. Due to the insulating behaviour of the layer, distinct craters developed on both limiter types, which reached down to the copper surface and are assumed to be caused by electrical arcs. An oscillation of the evolution of the surface temperature has been observed under certain conditions, which is clearly correlated to the use of the coated test limiter. Particle fluxes as well as hydrogen inventory turned out to be very similar to those from a low-Z surface in a carbon surrounding. No significant impact of the plasma on the coating and vice versa was observed.
|
|
| 3. |
- Tonderski, Karin S., et al.
(author)
-
Våtmarker : Närsaltsfällor och/eller myllrande mångfald?
- 2003
-
In: Vatten: tidskrift för vattenvård. - Nykvarn : Föreningen Vatten. - 0042-2886. ; 59:4, s. 259-270
-
Journal article (peer-reviewed)abstract
- This paper summarizes the state-of-the-art with respect to wetlands for nutrient removal and biodiversity enhancement, as expressed at a research workshop in December 2002. In the end of 2002, 260 and 884 wetlands had been constructed in Sweden with subsidies from LIP and the European Union, respectively. Most frequently, the aims were to remove nutrients from water and enhance biodiversity. The question raised is if we know how to design multifunctional wetlands. Should a wetland be deep or shallow, with or without macrophytes to be an efficient nutrient sink? Diverging opinions are presented, but generally it appears that fairly shallow wetlands at least partly covered by emergent macrophytes are favourable. The importance of extreme high flows and hydraulic short-circuiting is highlighted, and Danish and Norwegian approaches to wetlands construction are presented. Also, there is a risk that nutrient retaining wetlands develop a fairly trivial flora and fauna unless special care is taken. Intentional establishment of desirable and less common species, as well as creation of a variation of depth gradients to favour such species are such measures. Others are allowing for water level variations, as well as vegetation management such as grazing and harvesting.
|
|
| 4. |
|
|
| 5. |
|
|
