| 1. |
- Bernander, Stig, et al.
(author)
-
Downhill progressive landslides in long natural slopes: triggering agents and landslide phases modeled with a finite difference method
- 2016
-
In: Canadian geotechnical journal (Print). - : Canadian Science Publishing. - 0008-3674 .- 1208-6010. ; 53:10, s. 1565-1582
-
Journal article (peer-reviewed)abstract
- A large landslide in Tuve (Gothenburg, Sweden 1977) initiated the development of a model for slope stability analysis taking the deformation-softening of soft sensitive clays into consideration. The model studies triggering agents and five phases in progressive slope failure are identified: (1) in-situ, (2) disturbance, (3) unstable ‘dynamic’, (4) transitory (or permanent) equilibrium, and (5) ‘global’ failure. The clay resistance in these phases may differ widely; mostly due to different rates of loading. Two time dependent failure criteria are defined: (i) the triggering load condition in the disturbance Phase (2), and (ii) the transitory equilibrium in Phase (4), indicating whether minor downhill displacements or a veritable landslide catastrophe will occur. The analysis explains why downhill landslides tend to spread over vast areas of almost horizontal ground further down-slope. The model has been applied to landslides in Scandinavia and Canada. Three case studies are briefly discussed. The model is a finite difference approach, where local downhill deformations caused by normal forces is maintained compatible with deviatory shear deformations above the potential (or the established) failure surface. Software and an easy-to-use spreadsheet are introduced as well as recent developments. See also Video Abstract.
|
|
| 2. |
- Bouchelaghem, Fatiha, et al.
(author)
-
Fluid flow and effective conductivity calculations on numerical images of bentonite microstructure
- 2017
-
In: Applied Clay Science. - : Elsevier. - 0169-1317 .- 1872-9053. ; 144, s. 9-18
-
Journal article (peer-reviewed)abstract
- Hydraulic conductivities of compacted water-saturated bentonite were computed based on the real microstructure. The Homogenization of Periodic Media approach employed fully acknowledges the heterogeneous and multiscale microstructure of clay, as well as locally varying physical flow properties. Consequently, three levels of description were considered : the microscopic level of clay particles, the mesoscopic level of clay aggregates, mineral grains and inter-aggregate porosity, and the macroscopic level of the sample subjected to fluid pressure gradients in the laboratory. Starting from the local description of fluid flow, the expression of the effective hydraulic conductivity tensor was derived. The soft and dense gels and the open voids may form a connected flow path or remain occluded. The local problems were solved on the microstructure obtained from a digitalized micrograph by image analysis. The contribution to macroscopic flow by the soft and dense gels was investigated in various configurations, and comparisons were made with hydraulic conductivity data for MX-80 bentonite.
|
|
| 3. |
- Chabuk, Ali, et al.
(author)
-
Combining GIS Applications and Method of Multi-Criteria Decision-Making (AHP) for Landfill Siting in Al-Hashimiyah Qadhaa, Babylon, Iraq
- 2017
-
In: Sustainability. - Basel : MDPI. - 2071-1050. ; 9:11
-
Journal article (peer-reviewed)abstract
- Landfill siting is a complex process. It is one of the major problems in waste management, where many factors should be taken into consideration when selecting a suitable site for landfill in any given area. At the present time, there are many random waste disposal sites distributed throughout Al-Hashimiyah Qadhaa in Iraq. In this study, the Geographic Information System (GIS) and the Analytical Hierarchy Process (AHP) were used to select the best sites for landfill. The process of selecting sites for landfill in Al-Hashimiyah Qadhaa comprised two steps. First, fifteen different criteria were mapped and incorporated into overlay analyses within GIS software to produce the final suitability index map for the site. The second step comprises the exclusion of unsuitable areas from the final map to simplify identification of the candidate sites for landfill in the study area. The weightings of criteria were identified using AHP, and the weightings of the sub-criteria of each criterion were determined based on multiple factors. In order to accommodate solid waste from 2020 until 2030, two suitable candidate landfill sites were determined which fulfill the required area of 1.013 km2 with areas of 1.374 km2 and 1.288 km2 respectively.
|
|
| 4. |
- Chabuk, Ali, et al.
(author)
-
GIS-based assessment of combined AHP and SAW methods for selecting suitable sites for landfill in Al-Musayiab Qadhaa, Babylon, Iraq
- 2017
-
In: Environmental Earth Sciences. - : Springer. - 1866-6280 .- 1866-6299. ; 76:5
-
Journal article (peer-reviewed)abstract
- Selecting a landfill site is a difficult task because the process depends on many factors and restrictions. Landfill is an optimal solution for the disposal of solid waste in Al-Musayiab Qadhaa, which is located in the northern part of Babylon Governorate. At the moment, there is no landfill site in that area that follows the scientific selection site criteria. For this reason, in this research, fifteen variables were considered (groundwater depth, rivers, soil types; agriculture lands use, land use, elevation, slope, gas pipelines, oil pipelines, power lines, roads, railways, urban centers, villages and archeological sites) using geographic information system (GIS) to find out the best suitable landfill site. In addition, two methods of multi-criteria decision-making were used to derive weights for criterion’s maps on GIS to obtain potential landfill sites. The first method is analytical hierarchy process (AHP) which was used to identify the weight for each criterion from the matrix of pairwise comparisons. The second method was the simple additive weighting (SAW) which is a simple method to solve the problem of the selection landfill sites. After comparison of the results obtained based on combining two final maps resulted from methods of AHP and SAW using GIS environment to determine the pixels percentage of matching and non-matching for two maps, two suitable candidate landfill sites were identified that satisfy the requirements with an area of 7.965–5.952 km2. Area of these sites can accommodate the solid waste generated from the Qadhaa up to 2030.
|
|
| 5. |
- Chabuk, Ali Jalil
(author)
-
Analysis of Landfill Site Selection-Case Studies Al-Hillah and Al-Qasim Qadhaas, Babylon, Iraq
- 2016
-
Licentiate thesis (other academic/artistic)abstract
- The selection of a landfill site is considered as a complicated task because the whole process is based on many factors and restrictions. This study shows the present status of solid waste management, solid waste sources, staffing for solid waste collection, machinery and equipment used in the waste collection process, finance and financial management at Babylon Governorate and its Qadhaa. The management of collection and disposal of waste in Babylon Governorate and its Qadhaa is done through open dumping of waste and the quality of the collection process is poor. This is the case in Al-Hillah Qadhaa, which is located in the central part of the governorate, Iraq and Al-Qasim Qadhaas, which is situated in the southern part of the Babylon Governorate, Iraq. These sites do not conform to the scientific and environmental criteria applied in the selection of landfill sites. In the first part of the current study, to find out how much solid waste will be produced in the future; two methods were used to calculate the population growth in Al-Hillah and Al-Qasim Qadhaas to the year 2030. The results showed that the total waste in 2030 according to the first and second methods respectively will be 394,081 tonnes and 472,474 tonnes in Al-Hillah Qadhaa, and (54,481 tonnes and 76,374 tonnes) in Al-Qasim Qadhaa. The cumulated quantity of solid waste expected to be produced between 2020 and 2030 according to the first and second methods respectively was 3,757,387 tonnes and 4,300,864 tonnes in Al-Hillah Qadhaa, whilst in Al-Qasim Qadhaa it was 519,456 tonnes and 695,219 tonnes. The generation rate in 2020 will be (0.88 and 0.62) kg/ (capita. day) in Al-Hillah and Al-Qasim Qadhaas respectively; in year 2030, the generation rate will be (0.97 and 0.69) kg/ (capita. day) based on method 2 and an expected incremental increase in generation rate of 1 kg/ (capita. day) per year. The second part of this study aims to find the best sites for landfills in Al-Hillah and Al-Qasim Qadhaas. For this reason, 15 criteria were adopted in this study (groundwater depth, rivers, soil types, agricultural land use, land use, elevation, slope, gas pipelines, oil pipelines, power lines, roads, railways, urban centres, villages and archaeological sites) using GIS (geographic information system), which has a large capacity for managing input data. In addition, the AHP (analytical hierarchy process) method was used to derive the relative weightings for each criterion using pairwise comparison. The suitability index map for candidate landfill sites was obtained. Two suitable candidate landfill sites were found to fulfill the scientific and environmental requirements in each Qadhaa, with areas of 9.153 km2 and 8.204 km2 respectively in Al-Hillah Qadhaa, and with areas of 2.766 km2 and 2.055 km2 respectively in Al-Qasim Qadhaa. The area of these sites can accommodate solid waste from 2020 until 2030 based on the required areas, which were 4.175 km2 and 4.778 km2 (Ali-Hillah Qadhaa) and 0.577 km2 and 0.772 km2 in (Al-Qasim Qadhaa) according to the first and second methods respectively.
|
|
| 6. |
- Chabuk, Ali, et al.
(author)
-
Landfill Final Cover Systems Design for Arid Areas Using the HELP Model : A Case Study in the Babylon Governorate, Iraq
- 2018
-
In: Sustainability. - : MDPI. - 2071-1050. ; 10:12
-
Journal article (peer-reviewed)abstract
- The main purpose of selecting proper designs for landfills is to accommodate quantities of waste without having a negative effect on the surrounding environment and human health. The Babylon Governorate (province) in Iraq was taken as an example of an arid area with very shallow groundwater and where irregular waste disposal sites had developed that had not been subject to international standards when they were selected for landfill use. In the current study, the suggested design for landfills is a base liner and final cover system. In this suggested design, the final cover system allows for three scenarios. The first scenario considers an evapotranspiration soil cover (ET) (capillary barriers type), the second scenario is a modified cover design of “RCRA Subtitle D”, and the third scenario is a combination of the first and second scenarios. The HELP 3.95 D model was applied to the selected landfill sites in the governorate to check if there was any penetration of the leachate that might in future percolate from the landfill’s bottom barrier layer in arid areas. The results from the suggested landfill design showed that there was no leachate percolation from the bottom barrier layer using the second and third scenarios. For the first scenario, however, there was a small amount of leachate through the bottom barrier layer in the years 2013 and 2014.
|
|
| 7. |
- Chabuk, Ali, et al.
(author)
-
Landfill site selection using geographic information system and analytical hierarchy process : A case study Al-Hillah Qadhaa, Babylon, Iraq
- 2016
-
In: Waste Management & Research. - 0734-242X .- 1096-3669. ; 34:5, s. 427-437
-
Journal article (peer-reviewed)abstract
- Al-Hillah Qadhaa is located in the central part of Iraq. It covers an area of 908 km2 with a total population of 856,804 inhabitants. This Qadhaa is the capital of Babylon Governorate. Presently, no landfill site exists in that area based on scientific site selection criteria. For this reason, an attempt has been carried out to find the best locations for landfills. A total of 15 variables were considered in this process (groundwater depth, rivers, soil types, agricultural land use, land use, elevation, slope, gas pipelines, oil pipelines, power lines, roads, railways, urban centres, villages and archaeological sites) using a geographic information system. In addition, an analytical hierarchy process was used to identify the weight for each variable. Two suitable candidate landfill sites were determined that fulfil the requirements with an area of 9.153 km2 and 8.204 km2. These sites can accommodate solid waste till 2030
|
|
| 8. |
- Chabuk, Ali, et al.
(author)
-
Landfill Sites Selection Using Analytical Hierarchy Process and Ratio Scale Weighting : Case Study of Al-Mahawil, Babylon, Iraq
- 2017
-
In: Engineering. - : Scientific Research Publishing. - 1947-3931 .- 1947-394X. ; 9:2, s. 123-141
-
Journal article (peer-reviewed)abstract
- Selecting a landfill site is an optimal solution for the disposal of solid waste inAl-Mahawil Qadhaa, both to fulfill the environmental and scientific requirements,and to comply with regulations and restrictions in this Qadhaa. Presently,there is no landfill site in the area that meets the scientific site selection criteria.Therefore, in this study, two methods of multi-criteria decision-makingand Geographic Information System (GIS) were used to produce a map ofcandidate sites for landfill. Fifteen criteria were entered within GIS: groundwaterdepth, rivers, soil types; agriculture lands use, land use, elevation, slope,gas pipelines, oil pipelines, power lines, roads, railways, urban centers, villagesand archaeological sites. The Analytical Hierarchy Process (AHP) is the firstmethod that was applied to derive criteria weightings using the matrix of pairwisecomparisons. The second method was the Ratio Scale Weighting (RSW),which is based on experts’ opinion, in order to identify the criteria weightingsby giving a ratio score value for each criterion relative to the other criteria.Accuracy assessment (Kappa and Overall Assessment) methods were used tocompare the two raster maps which resulted from the two models, and to determinethe percentage value of matching pixels for the two maps. Two suitablecandidate sites for landfill were identified that satisfy the requirementswith an area of 2.218 km2 - 2.950 km2 in order to accommodate the solidwaste generated from the Qadhaa in the period 2020 to 2030.
|
|
| 9. |
- Chabuk, Ali, et al.
(author)
-
Landfill Sites Selection Using MCDM and Comparing Method of Change Detection for Babylon Governorate, Iraq
- 2019
-
In: Environmental Science and Pollution Research. - : Springer. - 0944-1344 .- 1614-7499. ; 26:35, s. 35325-35339
-
Journal article (peer-reviewed)abstract
- Landfill site`s selection represents a complicated process due to the large number of variables to be adopted. In this study, an arid area (Babylon Governorate as a case study) was selected. It is located in the middle region of Iraq. In this area, the landfills do not satisfy the required international criteria. Fifteen of the most significant criterion were selected for this purpose. For suitable weight for each criterion, the multi criteria decision making (MCDM) methods were applied. These methods are AHP and RSW. In the GIS software 10.5, the raster maps of the chosen criterion were arranged and analysed. The method of change detection was implemented to determine the matching pixels and non-matching pixels. The final results showed that there are two candidate locations for landfills for each district in the governorate (ten sites). The areas of the selected sites were sufficient to contain the cumulative quantity of solid waste from 2020 until 2030.
|
|
| 10. |
- Chabuk, Ali, et al.
(author)
-
Landfill Siting Using GIS and AHP (Analytical Hierarchy Process) : A Case Study Al-Qasim Qadhaa, Babylon, Iraq
- 2016
-
In: Journal of Civil Engineering and Architecture. - : David Publishing Company. - 1934-7359 .- 1934-7367. ; 5, s. 530-543
-
Journal article (peer-reviewed)abstract
- The selection of a landfill site is considered as a complicated task because this process is based on many factors and restrictions. For Al-Qasim Qadhaa, which is situated in the southern part of the Babylon Governorate, Iraq, there is no landfill site in that area that conforms to the scientific criteria for selecting sites for landfill. For this reason, 15 criteria were adopted in this study (groundwater depth, rivers, soil types, agriculture lands use, land use, elevation, slope, gas pipelines, oil pipelines, power lines, roads, railways, urban centers, villages and archaeological sites) using GIS (geographic information system), which has a large ability to manage input data. In addition, the AHP (analytical hierarchy process) method was used to derive the relative weightings for each criterion using pair-wise comparison. To obtain the suitability index for candidate landfill sites, a weighted linear combination method was used. After combining these methods, two suitable candidate landfill sites, with areas of 2.766 km2 and 2.055 km2, respectively, were found to satisfy the scientific and environmental requirements. The area of these sites can accommodate solid waste from 2020 until 2030 based on the required area, which was 0.702 km2.
|
|
