1. |
- Abel, I, et al.
(author)
-
Overview of the JET results with the ITER-like wall
- 2013
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Journal article (peer-reviewed)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
2. |
- Romanelli, F, et al.
(author)
-
Overview of the JET results
- 2011
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Journal article (peer-reviewed)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
3. |
- Litnovsky, A., et al.
(author)
-
Overview of material migration and mixing, fuel retention and cleaning of ITER-like castellated structures in TEXTOR
- 2011
-
In: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 415:1, s. S289-S292
-
Journal article (peer-reviewed)abstract
- Plasma-facing components (PFCs) in ITER will be castellated by splitting them into small-size blocks to maintain the thermo-mechanical stability. However, there are concerns in particular on retention of codeposited radioactive fuel in the gaps. An R&D program is underway in TEXTOR addressing this acute issue of castellation. Material migration and fuel inventory are investigated using long- and short-term discharge-resolved experiments with castellated structures in TEXTOR. Significant impurity transport to the gaps was detected and results were in part quantitatively reproduced with 3D-GAPS code. Deposits containing up to 70 at.% of tungsten on the gap areas closest to the plasma were detected in recent experiments. Deposition in the gaps accompanied by metal mixing demand for development of effective cleaning techniques. In experiments with ITER-like castellation, the gaps were cleaned from carbonaceous deposits using oxygen plasmas at 350 degrees C. This contribution contains an overview of experimental and modeling results along with recommendations for PFCs in ITER.
|
|
4. |
- Litnovsky, A., et al.
(author)
-
Dust investigations in TEXTOR : Impact of dust on plasma-wall interactions and on plasma performance
- 2013
-
In: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 438:Suppl., s. S126-S132
-
Journal article (peer-reviewed)abstract
- Dust will have severe impact on ITER performance since the accumulation of tritium in dust represents a safety issue, a possible reaction of dust with air and steam imposes an explosion hazard and the penetration of dust in core plasmas may degrade plasma performance by increasing radiative losses. Investigations were performed in TEXTOR where known amounts of pre-characterized carbon, diamond and tungsten dust were mobilized into plasmas using special dust holders. Mobilization of dust changed a balance between plasma-surface interactions processes, significantly increasing net deposition. Immediately after launch dust was dominating both core and edge plasma parameters. Remarkably, in about 100 ms after the launch, the effect of dust on edge and core plasma parameters was vanished: no increase of carbon and tungsten concentrations in the core plasmas was detected suggesting a prompt transport of dust to the nearby plasma-facing components without further residence in the plasma.
|
|
5. |
- Möller, S., et al.
(author)
-
Thermo-chemical fuel removal from porous materials by oxygen and nitrogen dioxide
- 2014
-
In: Physica Scripta. - 0031-8949 .- 1402-4896. ; T159, s. 014065-
-
Journal article (peer-reviewed)abstract
- Thermo-chemical removal (TCR), or baking in reactive gases, is a candidate method to control the co-deposit related tritium inventory in fusion devices. TCR can be understood as reaction-diffusion processes in a porous material. O-2-TCR was applied to 150-550 nm thick a-C:D layers with similar textures. A linear relation between the integral TCR rate and the layer thickness, as predicted by the understanding, was observed in the experiment, i.e. the time to remove the hydrogen inventory is independent of its initial amount. TCR with nitrogen dioxide (NO2) at temperatures of 200-350 degrees C was conducted with a set of a-C:D and W-C-H layers. At 350 degrees C NO2 removed similar to 15% porosity a-C:D within 3 min. The O retention in remaining a-C:D was approximate to 10(17) Ocm(-2). An activation energy of approximate to 0.78 eV for reactions of NO2 with D and C was determined. The results were applied for predictions of the TCR effectivity in ITER. The treatment of W-C-H led to O uptake (O/W approximate to 2-3), while W and C contents remained unchanged.
|
|