1. |
- Joffrin, E., et al.
(author)
-
Overview of the JET preparation for deuterium-tritium operation with the ITER like-wall
- 2019
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 59:11
-
Research review (peer-reviewed)abstract
- For the past several years, the JET scientific programme (Pamela et al 2007 Fusion Eng. Des. 82 590) has been engaged in a multi-campaign effort, including experiments in D, H and T, leading up to 2020 and the first experiments with 50%/50% D-T mixtures since 1997 and the first ever D-T plasmas with the ITER mix of plasma-facing component materials. For this purpose, a concerted physics and technology programme was launched with a view to prepare the D-T campaign (DTE2). This paper addresses the key elements developed by the JET programme directly contributing to the D-T preparation. This intense preparation includes the review of the physics basis for the D-T operational scenarios, including the fusion power predictions through first principle and integrated modelling, and the impact of isotopes in the operation and physics of D-T plasmas (thermal and particle transport, high confinement mode (H-mode) access, Be and W erosion, fuel recovery, etc). This effort also requires improving several aspects of plasma operation for DTE2, such as real time control schemes, heat load control, disruption avoidance and a mitigation system (including the installation of a new shattered pellet injector), novel ion cyclotron resonance heating schemes (such as the three-ions scheme), new diagnostics (neutron camera and spectrometer, active Alfven eigenmode antennas, neutral gauges, radiation hard imaging systems...) and the calibration of the JET neutron diagnostics at 14 MeV for accurate fusion power measurement. The active preparation of JET for the 2020 D-T campaign provides an incomparable source of information and a basis for the future D-T operation of ITER, and it is also foreseen that a large number of key physics issues will be addressed in support of burning plasmas.
|
|
2. |
- Bombarda, F., et al.
(author)
-
Runaway electron beam control
- 2019
-
In: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 1361-6587 .- 0741-3335. ; 61:1
-
Journal article (peer-reviewed)
|
|
3. |
|
|
4. |
|
|
5. |
- Tala, T., et al.
(author)
-
Density peaking in JET-determined by fuelling or transport?
- 2019
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 59:12
-
Journal article (peer-reviewed)abstract
- Core density profile peaking and electron particle transport have been extensively studied by performing several dimensionless collisionality (upsilon*) scans with other matched dimensionless profiles in various plasma operation scenarios on the Joint European Torus (JET). This is the first time when electron particle transport coefficients in the H-mode have been measured on JET with high resolution diagnostics, and therefore we are in a position to distinguish between the neutral beam injection (NBI) source and inward electron particle pinch in contributing to core density peaking. The NBI particle source is found to contribute typically 50%-60% to the electron density peaking in JET H-mode plasmas where T-e/T-i similar to 1 or smaller and at upsilon* = 0.1-0.5 (averaged between r/a = 0.3-0.8), and being independent of upsilon* within that range. In these H-mode plasmas, the electron particle transport coefficients, D-e and v(e), are small, thus giving rise to the large influence of NBI fueling with respect to transport effect on peaking. In L-mode plasma conditions, the role of the NBI source is small, typically 10%-20%, and the electron particle transport coefficients are large. These dimensionless upsilon* scans give the best possible data for model validation. TGLF simulations are in good agreement with the experimental results with respect to the role of NBI particle source versus inward pinch in affecting density peaking, both for the H-mode and L-mode upsilon* scans. It predicts, similarly to experimental results, that typically about half of the peaking originates from the NBI fuelling in the H-mode and 10%-20% in the L-mode. GENE simulation results also support the key role of NBI fuelling in causing a peaked density profile in JET H-mode plasma (T-e/T-i similar to 1 and upsilon* = 0.1-0.5) and, in fact, give an even higher weight on NBI fuelling than that experimentally observed or predicted by TGLF. For the non-fuelled H-mode plasma at higher T-e/T-i = 1.5 and lower beta(N) and upsilon*, both TGLF and GENE predict peaked density profiles, therefore agreeing well with experimental steady-state density peaking. Overall, the various modelling results give a fairly good confidence in using TGLF and GENE in predicting density peaking in quite a wide range of plasma conditions in JET.
|
|