1. |
- Bruzzi, M, et al.
(author)
-
Radiation-hard semiconductor detectors for SuperLHC
- 2005
-
In: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 541:1-2, s. 189-201
-
Journal article (peer-reviewed)abstract
- An option of increasing the luminosity of the Large Hadron Collider (LHC) at CERN to 1035 cm-2 s-1 has been envisaged to extend the physics reach of the machine. An efficient tracking down to a few centimetres from the interaction point will be required to exploit the physics potential of the upgraded LHC. As a consequence, the semiconductor detectors close to the interaction region will receive severe doses of fast hadron irradiation and the inner tracker detectors will need to survive fast hadron fluences of up to above 1016cm-2. The CERN-RD50 project "Development of Radiation Hard Semiconductor Devices for Very High Luminosity Colliders" has been established in 2002 to explore detector materials and technologies that will allow to operate devices up to, or beyond, this limit. The strategies followed by RD50 to enhance the radiation tolerance include the development of new or defect engineered detector materials (SiC, GaN, Czochralski and epitaxial silicon, oxygen enriched Float Zone silicon), the improvement of present detector designs and the understanding of the microscopic defects causing the degradation of the irradiated detectors. The latest advancements within the RD50 collaboration on radiation hard semiconductor detectors will be reviewed and discussed in this work.
|
|
2. |
- Hellsten, Torbjörn, et al.
(author)
-
Fast wave current drive in JET ITB-plasma
- 2005
-
In: AIP Conference Proceedings. - : AIP. - 0094-243X. ; , s. 273-278
-
Conference paper (peer-reviewed)abstract
- Fast wave current drive has been performed in JET plasmas with internal transport barriers, ITBs, and strongly reversed magnetic shear. Although the current drive efficiency of the power absorbed on the electrons is fairly high, only small effects are seen in the central current density. The main reasons are the parasitic absorption of RF power, the strongly inductive nature of the plasma and the interplay between the fast wave driven current and bootstrap current. The direct electron heating in the FWCD experiments is found to be strongly degraded compared to that with the dipole phasing.
|
|
3. |
- Lamalle, P.U, et al.
(author)
-
Expanding the operating space of ICRF on JET with a view to ITER
- 2006
-
In: Nucl. Fusion. ; 46, s. 391-
-
Journal article (peer-reviewed)abstract
- Mercury (Hg) has been used for millennia in many applications, primarily in artisanal mining and as an electrode in the chlor–alkali industry. It is anthropogenically emitted as a pollutant from coal fired power plants and naturally emitted, primarily from volcanoes. Its unique chemical characteristics enable global atmospheric transport and it is deposited after various processes, ultimately ending up in one of its final sinks, such as incorporated into deep sediment or bioaccumulated, primarily in the marine environment. All forms of Hg have been established as toxic, and there have been no noted biological benefits from the metal.Throughout time, there have been notable incidents of Hg intoxication documented, and the negative health effects have been documented to those chronically or acutely exposed. Today, exposure to Hg is largely diet or occupationally dependent, however, many are exposed to Hg from their amalgam fillings. This paper puts a tentative monetary value on Hg polluted food sources in the Arctic, where local, significant pollution sources are limited, and relates this to costs for strategies avoiding Hg pollution and to remediation costs of contaminated sites in Sweden and Japan. The case studies are compiled to help policy makers and the public to evaluate whether the benefits to the global environment from banning Hg and limiting its initial emission outweigh the benefits from its continued use or lack of control of Hg emissions. The cases we studied are relevant for point pollution sources globally and their remediation costs ranged between 2500 and 1.1 million US$ kg−1 Hg isolated from the biosphere. Therefore, regulations discontinuing mercury uses combined with extensive flue gas cleaning for all power plants and waste incinerators is cost effective.
|
|
4. |
- Stork, D., et al.
(author)
-
Overview of transport, fast particle and heating and current drive physics using tritium in JET plasmas
- 2005
-
In: Nuclear Fusion. - 0029-5515 .- 1741-4326. ; 45:10, s. S181-S194
-
Journal article (peer-reviewed)abstract
- Results are presented from the JET Trace Tritium Experimental (TTE) campaign using minority tritium (T) plasmas (n(T)/n(D) < 3%). Thermal tritium particle transport coefficients (D-T, nu(T)) are found to exceed neo-classical values in all regimes, except in ELMy H-modes at high densities and in the region of internal transport barriers (ITBs) in reversed shear plasmas. In ELMy H-mode dimensionless parameter scans, at q(95) 2.8 and triangularity delta = 0.2, the T particle transport scales in a gyro-Bohm manner in the inner plasma (r/a < 0.4), whilst the outer plasma particle transport scaling is more Bohm-like. Dimensionless parameter scans show contrasting behaviour for the trace particle confinement (increases with collisionality, nu* and beta) and bulk energy confinement (decreases with nu* and is independent of beta). In an extended ELMy H-mode data set, with rho*, nu*, and q varied but with neo-classical tearing modes (NTMs) either absent or limited to weak, benign core modes (4/3 or above), the multiparameter fit to the normalized diffusion coefficient in the outer plasma (0.65 < r/a < 0.8) gives D-T/B-phi similar to rho*(2.46) nu*(-0.23) beta(-1.01) q(2.03). In hybrid scenarios (q(min) similar to 1, low positive shear, no sawteeth), the T particle confinement is found to scale with increasing triangularity and plasma current. Comparing regimes (ELMy H-mode, ITB plasma and hybrid scenarios) in the outer plasma region, a correlation of high values of D-T with high values Of nu(T) is seen. The normalized diffusion coefficients for the hybrid and ITB scenarios do not fit the scaling derived for ELMy H-modes. The normalized tritium diffusion scales with normalized poloidal Larmor radius (rho(theta)* = q rho*) in a manner close to gyro-Bohm (similar to rho(sigma)*(3)), with an added inverse P dependence. The effects of ELMs, sawteeth and NTMs on the T particle transport are described. Fast-ion confinement in current-hole (CH) plasmas was tested in TTE by tritium neutral beam injection into JET CH plasmas. gamma-rays from the reactions of fusion alpha and beryllium impurities (Be-9(alpha, n gamma)C-12) characterized the fast fusion-alpha population evolution. The gamma-decay times are consistent with classical alpha plus parent fast triton slowing down times (tau(Ts) + tau(alpha s)) for high plasma currents (I-p > 2 MA) and monotonic q-profiles. In CH discharges the gamma-ray emission decay times are much lower than classical (tau(Ts) + tau(alpha s)), indicating alpha confinement degradation, due to the orbit losses and particle orbit drift predicted by a 3-D Fokker-Planck numerical code and modelled using TRANSP.
|
|
5. |
- Lamalle, P. U., et al.
(author)
-
Expanding the operating space of ICRF on JET with a view to ITER
- 2006
-
In: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 46:2, s. 391-400
-
Journal article (peer-reviewed)abstract
- This paper reports on ITER-relevant ion cyclotron resonance frequency (ICRF) physics investigated on JET in 2003 and early 2004. Minority heating of helium three in hydrogen plasmas-(He-3)H-was systematically explored by varying the 3 He concentration and the toroidal phasing of the antenna arrays. The best heating performance (a maximum electron temperature of 6.2 keV with 5 MW of ICRF power) was obtained with a preferential wave launch in the direction of the plasma current. A clear experimental demonstration was made of the sharp and reproducible transition to the mode conversion heating regime when the 3 He concentration increased above similar to 2%. In the latter regime the best heating performance (a maximum electron temperature of 8 keV with 5 MW of ICRF power) was achieved with dipole array phasing, i.e. a symmetric antenna power spectrum. Minority heating of deuterium in hydrogen plasmas-(D)H-was also investigated but was found inaccessible because this scenario is too sensitive to impurity ions with Z/A = 1/2 such as C6+, small amounts of which directly lead into the mode conversion regime. Minority heating of up to 3% of tritium in deuterium plasmas was systematically investigated during the JET trace tritium experimental campaign (TTE). This required operating JET at its highest possible magnetic field (3.9 to 4 T) and the ICRF system at its lowest frequency (23 MHz). The interest of this scenario for ICRF heating at these low concentrations and its efficiency at boosting the suprathermal neutron yield were confirmed, and the measured neutron and gammay ray spectra permit interesting comparisons with advanced ICRF code simulations. Investigations of finite Larmor radius effects on the RF-induced high-energy tails during second harmonic (omega = 2 omega(c)) heating of a hydrogen minority in D plasmas clearly demonstrated a strong decrease in the RF diffusion coefficient at proton energies similar to 1 MeV in agreement with theoretical expectations. Fast wave heating and current drive experiments in deuterium plasmas showed effective direct electron heating with dipole phasing of the antennas, but only small changes of the central plasma current density were observed with the directive phasings, in particular at low single pass damping. New investigations of the heating efficiency of ICRF antennas confirmed its strong dependence on the parallel wavenumber spectrum. Advances in topics of a more technological nature are also summarized: ELM studies using fast RF measurements, the successful experimental demonstration of a new ELM-tolerant antenna matching scheme and technical enhancements planned on the JET ICRF system for 2006, they being equally strongly driven by the preparation for ITER.
|
|
6. |
|
|
7. |
- de Vries, P. C., et al.
(author)
-
Effect of toroidal field ripple on the formation of internal transport barriers
- 2008
-
In: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 50:6
-
Journal article (peer-reviewed)abstract
- The effect of a toroidal field (TF) ripple on the formation and performance of internal transport barriers (ITBs) has been studied in JET. It was found that the TF ripple had a profound effect on the toroidal plasma rotation. An increased TF ripple up to delta = 1% led to a lower rotation and reduced the rotational shear in the region where the ITBs were formed. ITB triggering events were observed in all cases and it is thought that the rotational shear may be less important for this process than, for example, the q-profile. However, the increase in the pressure gradient following the ITB trigger was reduced in discharges with a larger TF ripple and consequently a lower rotational shear. This suggests that toroidal rotation and its shear play a role in the growth of the ITB once it has been triggered.
|
|
8. |
- Eriksson, L. -G, et al.
(author)
-
Toroidal rotation in RF heated JET plasmas
- 2007
-
In: RADIO FREQUENCY POWER IN PLASMAS. - : AIP. - 9780735404441 ; , s. 59-62
-
Conference paper (peer-reviewed)abstract
- Experiments have been carried out on JET aimed at studying rotation in RF heated plasmas with low external momentum input. Both plasmas with Ion Cyclotron Resonance Frequency (ICRF) heating and Lower Hybrid Current Drive (LHCD) have been investigated. The rotation profiles are measured by Charge Exchange recombination spectroscopy, using short diagnostic Neutral Beam Injection (NBI) pulses. Moreover, the temporal evolution of the central rotation could in some cases be deduced from MHD activity. While most of the measurements were focussed on ICRF heating, the profiles measured in plasmas with LHCD are interesting since they are the first reported from JET in such plasmas. In particular, they allowed for studies of rotation in RF heated plasmas with q>1. The experimental results are presented together with an analysis of the torque from ICRF heated fast ions.
|
|
9. |
|
|
10. |
- Loarer, T., et al.
(author)
-
Fuel retention in L and H mode experiments in JET
- 2007
-
In: 34th EPS Conference on Plasma Physics 2007, EPS 2007 - Europhysics Conference Abstracts. - 9781622763344 ; , s. 13-16
-
Conference paper (peer-reviewed)abstract
- The fuel retention has been studied out in JET in L mode, Type III and Type I ELMy H-modes using gas balance in series of repetitive pulses with an overall accuracy of about 1.2%. The short term (dynamic) retention is important for both L mode and Type III ELMy H-mode over the heating phases (respectively 13 and 17 sec) but decreases already significantly during the pulse. It becomes small already after 6 sec for the Type I ELMy H-mode conditions. In all the cases, the recovery after the pulse contributes for a weak part in the gas balance and in the overall fuel retention. The absolute long term fuel retention (on the time basis of typically 5 hours) for the different plasma conditions is between 1.3 and 2.8 1021Ds-1 (averaged over the plasma heating time) and in reasonable agreement with the value deduced from post mortem tile analysis of about 5 1020Ds-1 considering the additional long term outgassing, conditioning and disruptions included in the post mortem analysis. The increase of the long term retention observed from L mode to Type I ELMy H-mode is associated to the increase of the recycling flux and the ELM energy. This larger long term retention is attributed to an enhanced carbon erosion and transport in the SOL leading to stronger carbon deposition and fuel codeposition. The results confirm the strong concerns about fuel retention in a carbon clad tokamak and a possible full carbon wall ITER which could reach the T-inventory limit in only a small number of high performance shots. A reasonable ITER operation time depends thus on a significant reduced T codeposition under the different ITER material conditions (which has to be confirmed in a relevant tokamak experiment such as the JET ILW project) and an effective routine T removal technique.
|
|
11. |
|
|
12. |
- Santala, M. I. K., et al.
(author)
-
Proton-triton nuclear reaction in ICRF heated plasmas in JET
- 2006
-
In: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 48:8, s. 1233-1253
-
Journal article (peer-reviewed)abstract
- Fast protons can react with tritons in an endothermic nuclear reaction which can act as a source of neutrons in magnetically confined fusion plasmas. We have performed an experiment to systematically study this reaction in low tritium concentration (approximate to 1%) plasmas in the Joint European Torus. A linear dependence is found between excess neutron rate and tritium concentration when the DT fusion rate is low. We discuss the properties of the neutron emission, including anisotropy, from the proton-triton reaction in a fusion reactor environment and derive simple models for the calculation of the neutron yield from this reaction in terms of tritium density, fast ion temperature and fast ion energy content.
|
|
13. |
|
|
14. |
- Eriksson, L. G., et al.
(author)
-
Toroidal rotation in RF heated JET plasmas
- 2009
-
In: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 51:4
-
Journal article (peer-reviewed)abstract
- Observations of bulk plasma rotation in radio frequency (RF) heated JET discharges are reported. This study is concentrated on RF heated L-mode plasmas. In particular, the toroidal rotation profiles in plasmas heated by ion cyclotron resonance frequency (ICRF) waves and lower hybrid (LH) waves have been analysed. It is the first time that rotation profiles in JET plasmas with LH waves have been measured in dedicated discharges. It is found that the toroidal plasma rotation in the outer region of the plasmas is in the co-current direction irrespective of the heating scenario. An interesting feature is that the toroidal rotation profile appears to be hollow in many discharges at low plasma current, but a low current in itself does not seem to be a sufficient condition for finding such profiles. Fast ion transport and finite orbit width effects are mechanisms that could explain hollow rotation profiles. This possibility has been investigated by numerical simulations of the torque on the bulk plasma due to fast ICRF accelerated ions. The obtained torque is used in a transport equation for the toroidal momentum density to estimate the effect on the thermal bulk plasma rotation profile.
|
|
15. |
- Moreau, D., et al.
(author)
-
A two-time-scale dynamic-model approach for magnetic and kinetic profile control in advanced tokamak scenarios on JET
- 2008
-
In: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 48:10
-
Journal article (peer-reviewed)abstract
- Real-time simultaneous control of several radially distributed magnetic and kinetic plasma parameters is being investigated on JET, in view of developing integrated control of advanced tokamak scenarios. This paper describes the new model-based profile controller which has been implemented during the 2006-2007 experimental campaigns. The controller aims to use the combination of heating and current drive (H&CD) systems-and optionally the poloidal field (PF) system-in an optimal way to regulate the evolution of plasma parameter profiles such as the safety factor, q(x), and gyro-normalized temperature gradient,. rho*(Te)(x). In the first part of the paper, a technique for the experimental identification of a minimal dynamic plasma model is described, taking into account the physical structure and couplings of the transport equations, but making no quantitative assumptions on the transport coefficients or on their dependences. To cope with the high dimensionality of the state space and the large ratio between the time scales involved, the model identification procedure and the controller design both make use of the theory of singularly perturbed systems by means of a two-time-scale approximation. The second part of the paper provides the theoretical basis for the controller design. The profile controller is articulated around two composite feedback loops operating on the magnetic and kinetic time scales, respectively, and supplemented by a feedforward compensation of density variations. For any chosen set of target profiles, the closest self-consistent state achievable with the available actuators is uniquely defined. It is reached, with no steady state offset, through a near-optimal
|
|
16. |
- Murari, A., et al.
(author)
-
JET new diagnostic capability on the route to ITER
- 2007
-
In: Fusion engineering and design. - : Elsevier BV. - 0920-3796 .- 1873-7196. ; 82:14-maj, s. 1161-1166
-
Journal article (peer-reviewed)abstract
- The JET scientific programme is directed towards the development of ITER relevant scenarios. In support of this, significant effort has been made to develop diagnostics to better characterise the power deposition on the plasma facing components, to investigate in more detail the radiation losses particularly in the divertor region and to better detect Magneto Hydrodynamic Modes (MHD) instabilities and their effects on fast ion confinement. A new wide-angle infrared camera provides for the first time the opportunity to perform infrared thermography in the JET main chamber, even during fast events like ELMs and disruptions. A completely new bolometric system, with better spatial resolution particularly in the divertor, is now used to investigate the total radiation losses and their influence on the ELM behaviour. A new set of microwave waveguides has improved by 20 dB the signal to noise ratio of the JET X-mode reflectometers, that are now routinely used to detect MHD instabilities and in particular to localise the location of Alfven Eigenmodes. This improved diagnostic capability to monitor MHD instabilities is complemented by two new diagnostics to detect lost fast particles. Both the new scintillator probe and a poloidal array of Faraday cups have already shown clear correlations between MHD activity and ion losses at the edge.
|
|
17. |
- Murari, A., et al.
(author)
-
Measuring the radiation field and radiation hard detectors at JET : Recent developments
- 2008
-
In: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 593:3, s. 492-504
-
Journal article (peer-reviewed)abstract
- Since in ITER the radiation field will be much more demanding than that of present day devices, research programmes at JET are aimed at developing radiation hard diagnostics and related components. Initially, significant efforts are devoted to determining the radiation field of both the plasma and in the immediate environment with better accuracy. New developments in MCNP calculations and dedicated measurements provide useful information about the radiation field in the Torus Hall, even during non-operational periods. The effect of using Beryllium in the near future for JET first wall, is being assessed. New materials for activation samples are under consideration and will be tested to improve the calibration accuracy of JET neutron diagnostics. The long-term goal of this work is to obtain spectrometric information from an appropriate combination of different materials. Several studies are under way to modify the radiation field at the detectors by using LiH or pure water as neutron filters, to alleviate the problem of the background in gamma-ray measurements. A suite of radiation hard detectors for neutrons, magnetic field and charged particles are being developed. Super-heated fluid neutron detectors, used for yield and imaging, are being upgraded, in order to provide a broadband spectrometric capability. Chemical vapour deposited diamond diodes are being qualified as counters and as spectrometers. Prototypes of Hall probes made of InSb have been installed on the machine and have provided some preliminary results. Si-on-insulator detectors are under development for use in neutral particle analysers and are currently being bench-tested. Some attention is being devoted to optical components, fibres and mirrors, and to investigating radiation hard electronics using reconfigurable Field Programmable Gate Arrays.
|
|
18. |
- Murari, A., et al.
(author)
-
New diagnostic techniques and technologies at JET (invited)
- 2006
-
In: Review of Scientific Instruments. - : AIP Publishing. - 0034-6748 .- 1089-7623. ; 77:10
-
Journal article (peer-reviewed)abstract
- The European Fusion Development Agreement's mission for JET is the development of ITER scenarios exploiting the specific properties of the device. This task requires significant improvements in the measuring techniques. The most innovative diagnostic upgrades are in the fields of edge measurements, detection of fast magnetohydrodynamics modes and burning plasma diagnostics. The importance of plasma-wall interactions, and, in particular, the issue of tritium inventory promoted the development of the quartz microbalance, a detector with improved time resolution to measure material redeposition in the remote areas of the inner divertor. Measurement of Alfven cascades with unprecedented spectral resolution, reaching a toroidal n number of up to 16, was obtained using an O-mode microwave reflectometer as an interferometer. For the diagnosis of the fusion products, a new approach is being developed to measure the He ash based on double charge exchange between thermalized particles and neutrals from JET beams. There have been several upgrades of the neutron diagnostic systems, one of which, the new time of flight neutron spectrometer designed for high counting rates is described.
|
|