| 1. |
- Abate, E., et al.
(author)
-
Combined performance tests before installation of the ATLAS Semiconductor and Transition Radiation Tracking Detectors
- 2008
-
In: Journal of Instrumentation. - 1748-0221. ; 3
-
Journal article (peer-reviewed)abstract
- The ATLAS (A Toroidal LHC ApparatuS) Inner Detector provides charged particle tracking in the centre of the ATLAS experiment at the Large Hadron Collider (LHC). The Inner Detector consists of three subdetectors: the Pixel Detector, the Semiconductor Tracker (SCT), and the Transition Radiation Tracker (TRT). This paper summarizes the tests that were carried out at the final stage of SCT+TRT integration prior to their installation in ATLAS. The combined operation and performance of the SCT and TRT barrel and endcap detectors was investigated through a series of noise tests, and by recording the tracks of cosmic rays. This was a crucial test of hardware and software of the combined tracker detector systems. The results of noise and cross-talk tests on the SCT and TRT in their final assembled configuration, using final readout and supply hardware and software, are reported. The reconstruction and analysis of the recorded cosmic tracks allowed testing of the offline analysis chain and verification of basic tracker performance parameters, such as efficiency and spatial resolution, in combined operation before installation.
|
|
| 2. |
- Abdesselam, A., et al.
(author)
-
The ATLAS semiconductor tracker end-cap module
- 2007
-
In: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 575:3, s. 353-389
-
Journal article (peer-reviewed)abstract
- The challenges for the tracking detector systems at the LHC are unprecedented in terms of the number of channels, the required read-out speed and the expected radiation levels. The ATLAS Semiconductor Tracker. (SCT) end-caps have a total of about 3 million electronics channels each reading out every 25 ns into its own on-chip 3.3 mu s buffer. The highest anticipated dose after 10 years operation is 1.4x10(14) cm(-2) in units of 1 MeV neutron equivalent (assuming the damage factors scale with the non-ionising energy loss). The forward tracker has 1976 double-sided modules, mostly of area similar to 70 cm(2), each having 2 x 768 strips read out by six ASICs per side. The requirement to achieve an average perpendicular radiation length of 1.5% X-0, while coping with up to 7 W dissipation per module (after irradiation), leads to stringent constraints on the thermal design. The additional requirement of 1500e(-) equivalent noise charge (ENC) rising to only 1800e(-) ENC after irradiation, provides stringent design constraints on both the high-density Cu/Polyimide flex read-out circuit and the ABCD3TA read-out ASICs. Finally, the accuracy of module assembly must not compromise the 16 mu m (r phi) resolution perpendicular to the strip directions or 580 mu m radial resolution coming from the 40 mrad front-back stereo angle. A total of 2210 modules were built to the tight tolerances and specifications required for the SCT. This was 234 more than the 1976 required and represents a yield of 93%. The component flow was at times tight, but the module production rate of 40-50 per week was maintained despite this. The distributed production was not found to be a major logistical problem and it allowed additional flexibility to take advantage of where the effort was available, including any spare capacity, for building the end-cap modules. The collaboration that produced the ATLAS SCT end-cap modules kept in close contact at all times so that the effects of shortages or stoppages at different sites could be rapidly resolved.
|
|
| 3. |
- Abdesselam, A., et al.
(author)
-
Engineering for the ATLAS SemiConductor Tracker (SCT) end-cap
- 2008
-
In: Journal of Instrumentation. - 1748-0221. ; 3
-
Journal article (peer-reviewed)abstract
- The ATLAS SemiConductor Tracker (SCT) is a silicon-strip tracking detector which forms part of the ATLAS inner detector. The SCT is designed to track charged particles produced in proton-proton collisions at the Large Hadron Collider (LHC) at CERN at an energy of 14 TeV. The tracker is made up of a central barrel and two identical end-caps. The barrel contains 2112 silicon modules, while each end-cap contains 988 modules. The overall tracking performance depends not only on the intrinsic measurement precision of the modules but also on the characteristics of the whole assembly, in particular, the stability and the total material budget. This paper describes the engineering design and construction of the SCT end-caps, which are required to support mechanically the silicon modules, supply services to them and provide a suitable environment within the inner detector. Critical engineering choices are highlighted and innovative solutions are presented - these will be of interest to other builders of large-scale tracking detectors. The SCT end-caps will be fully connected at the start of 2008. Further commissioning will continue, to be ready for proton-proton collision data in 2008.
|
|
| 4. |
- Abdesselam, A., et al.
(author)
-
The barrel modules of the ATLAS semiconductor tracker
- 2006
-
In: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 568:2, s. 642-671
-
Journal article (peer-reviewed)abstract
- This paper describes the silicon microstrip modules in the barrel section of the SemiConductor Tracker (SCT) of the ATLAS experiment at the CERN Large Hadron Collider (LHC). The module requirements, components and assembly techniques are given, as well as first results of the module performance on the fully assembled barrels that make up the detector being installed in the ATLAS experiment.
|
|
| 5. |
|
|
| 6. |
- Carninci, P, et al.
(author)
-
The transcriptional landscape of the mammalian genome
- 2005
-
In: Science (New York, N.Y.). - : American Association for the Advancement of Science (AAAS). - 1095-9203 .- 0036-8075. ; 309:5740, s. 1559-1563
-
Journal article (peer-reviewed)abstract
- This study describes comprehensive polling of transcription start and termination sites and analysis of previously unidentified full-length complementary DNAs derived from the mouse genome. We identify the 5′ and 3′ boundaries of 181,047 transcripts with extensive variation in transcripts arising from alternative promoter usage, splicing, and polyadenylation. There are 16,247 new mouse protein-coding transcripts, including 5154 encoding previously unidentified proteins. Genomic mapping of the transcriptome reveals transcriptional forests, with overlapping transcription on both strands, separated by deserts in which few transcripts are observed. The data provide a comprehensive platform for the comparative analysis of mammalian transcriptional regulation in differentiation and development.
|
|
| 7. |
- Doornenbal, P., et al.
(author)
-
Spectroscopy of 32Ne and the "œIsland of Inversion"
- 2009
-
In: Physical Review Letters. - American Physical Society. - 0031-9007 .- 1079-7114. ; 103:3, s. 032501-1-032501-4
-
Journal article (peer-reviewed)abstract
- We report on the first spectroscopic study of the N = 22 nucleus 32Ne at the newly completed RIKEN Radioactive Ion Beam Factory. A single γ-ray line with an energy of 722(9) keV was observed in both inelastic scattering of a 226 MeV=u 32Ne beam on a carbon target and proton removal from 33Na at 245 MeV=u. This transition is assigned to the deexcitation of the first Jπ = 2+ state in 32Ne to the 0+ ground state. Interpreted through comparison with state-of-the-art shell-model calculations, the low excitation energy demonstrates that the ‘‘island of inversion’’ extends to at least N = 22 for the Ne isotopes.
|
|
| 8. |
- Pirozhkov, A. S., et al.
(author)
-
Diagnostic of laser contrast using target reflectivity
- 2009
-
In: Applied Physics Letters. - : AIP Publishing. - 0003-6951 .- 1077-3118. ; 94:24
-
Journal article (peer-reviewed)abstract
- Using three different laser systems, we demonstrate a convenient and simple plasma based diagnostic of the contrast of high-power short-pulse lasers. The technique is based on measuring the specular reflectivity from a solid target. The reflectivity remains high even at relativistic intensities above 10(19) W/cm(2) in the case of a high-contrast prepulse-free laser. On the contrary, the specular reflectivity drops with increasing intensities in the case of systems with insufficient contrast due to beam breakup and increased absorption caused by preplasma.
|
|
| 9. |
- Jimenez, J. L., et al.
(author)
-
Evolution of Organic Aerosols in the Atmosphere
- 2009
-
In: Science. - : American Association for the Advancement of Science (AAAS). - 0036-8075 .- 1095-9203. ; 326:5959, s. 1525-1529
-
Journal article (peer-reviewed)abstract
- Organic aerosol (OA) particles affect climate forcing and human health, but their sources and evolution remain poorly characterized. We present a unifying model framework describing the atmospheric evolution of OA that is constrained by high-time-resolution measurements of its composition, volatility, and oxidation state. OA and OA precursor gases evolve by becoming increasingly oxidized, less volatile, and more hygroscopic, leading to the formation of oxygenated organic aerosol (OOA), with concentrations comparable to those of sulfate aerosol throughout the Northern Hemisphere. Our model framework captures the dynamic aging behavior observed in both the atmosphere and laboratory: It can serve as a basis for improving parameterizations in regional and global models.
|
|
| 10. |
- Yamamoto, A., et al.
(author)
-
The ATLAS central solenoid
- 2008
-
In: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 584:1, s. 53-74
-
Journal article (peer-reviewed)abstract
- The ATLAS detector at the CERN LHC is equipped with a superconducting magnet system consisting of three large toroids and a solenoid. The 2.3 m diameter, 5.3 m long solenoid is located at the heart of the experiment where it provides a 2 T field for spectrometry of the particles emanating from the interaction of the counter-rotating beams of hadrons. As the electromagnetic calorimeter of the experiment is situated outside the solenoid, the coil must be as transparent as possible to traversing particles. The magnet, which was designed at KEK, incorporates progress in technology coming from the development of previous solenoids of this type, in particular that of a new type of reinforced superconductor addressing the requirement of transparency. Special attention has been paid to ensuring reliability and ease of operation of the magnet, through the application of sufficiently conservative guidelines for the mechanical and electrical design, stringent testing during manufacture, and a comprehensive commissioning program. This report gives an overview of the design, manufacture, test, installation and commissioning of the ATLAS central solenoid.
|
|
| 11. |
- Klionsky, Daniel J., et al.
(author)
-
Guidelines for the use and interpretation of assays for monitoring autophagy in higher eukaryotes
- 2008
-
In: Autophagy. - : Landes Bioscience. - 1554-8627 .- 1554-8635. ; 4:2, s. 151-175
-
Research review (peer-reviewed)abstract
- Research in autophagy continues to accelerate,1 and as a result many new scientists are entering the field. Accordingly, it is important to establish a standard set of criteria for monitoring macroautophagy in different organisms. Recent reviews have described the range of assays that have been used for this purpose.2,3 There are many useful and convenient methods that can be used to monitor macroautophagy in yeast, but relatively few in other model systems, and there is much confusion regarding acceptable methods to measure macroautophagy in higher eukaryotes. A key point that needs to be emphasized is that there is a difference between measurements that monitor the numbers of autophagosomes versus those that measure flux through the autophagy pathway; thus, a block in macroautophagy that results in autophagosome accumulation needs to be differentiated from fully functional autophagy that includes delivery to, and degradation within, lysosomes (in most higher eukaryotes) or the vacuole (in plants and fungi). Here, we present a set of guidelines for the selection and interpretation of the methods that can be used by investigators who are attempting to examine macroautophagy and related processes, as well as by reviewers who need to provide realistic and reasonable critiques of papers that investigate these processes. This set of guidelines is not meant to be a formulaic set of rules, because the appropriate assays depend in part on the question being asked and the system being used. In addition, we emphasize that no individual assay is guaranteed to be the most appropriate one in every situation, and we strongly recommend the use of multiple assays to verify an autophagic response.
|
|
| 12. |
- Abd-Alla, E. S. M ., et al.
(author)
-
New wheel tracking test to analyze movements of aggregates in multi-layered asphalt specimens
- 2006
-
In: Journal of the Japan Petroleum Institute. - : Japan Petroleum Institute. - 1346-8804 .- 1349-273X. ; 49:5, s. 274-279
-
Journal article (peer-reviewed)abstract
- This paper describes a new wheel tracking test for analyzing movements of aggregates in mixtures. The test device is conducted using as examples four-layered specimens taken from two Swiss national motorways, where severe rutting (G section) and longitudinal cracking (H section) were observed. This test method was developed by Moriyoshi. Tests can be carried out under temperature distributions similar to field situation. Two-dimensional movements and strains between aggregates for four-layered specimens due to the moving wheel loads were analyzed by right angle for direction of wheel pass. For this purpose, the cross section of the slabs with a width of 30 cm was divided optically into 5 vertical subsections. The transverse permanent surface deformations, the area changes in the transversal subsections as well as the maximum deformation of the surface and layer-interface through the centerline of the applied wheel load were determined. Strain distributions between aggregates in mixtures at high temperature (45 degrees C) under 600 passes were also measured by photo analysis. Test results show consolidation of the asphalt mixtures and material flow on the surface near the wheel load. The results also demonstrate that the aggregates (size of aggregate: 2 mm or larger) in each mixture move mainly in vertical direction. Large strains (40% or larger) between aggregates at summer condition were measured in the surface mixture near wheel track after 600 passes.
|
|
| 13. |
- Achtert, Peggy, 1982-, et al.
(author)
-
Hygroscopic growth of tropospheric particle number size distributions over the North China Plain
- 2009
-
In: Journal of Geophysical Research. - 0148-0227 .- 2156-2202. ; 114, s. D00G07-
-
Journal article (peer-reviewed)abstract
- The hygroscopic growth of atmospheric submicrometer particle size distributions (diameter D-p ranging from 22 to 900 nm) was studied at a rural/suburban site in the North China Plain within the framework of the international Campaigns of Air Quality Research in Beijing and Surrounding Region 2006 (CAREBeijing-2006) research project. The goal was to characterize the regional aerosol in the polluted northeastern plain in China. Size descriptive hygroscopic growth factors (DHGFs) were determined as a function of relative humidity (RH) by relating the particle number size distribution at a dry condition ( 100 nm), the DHGF are substantially higher than in the Aitken particle mode (D-p < 100 nm) as a result of different chemical composition. The size-dependent behavior of the DHGF highlights the relevance of particulate sulfate production over the North China Plain, accomplished by secondary formation from the gas phase and, potentially, liquid phase processes in convective clouds. Furthermore, all results concerning the DHGF show a significant dependency on meteorological air masses. The hygroscopic growth of accumulation mode particles correlates significantly with the PM1-mass fraction of sulfate ions determined by chemical analysis. Finally, this investigation provides a parameterization of the hygroscopic growth of 250-nm particles, which might be useful when predicting visibility and radiative forcing and performing atmospheric aerosol model validations.
|
|
| 14. |
|
|
