| 1. |
- Överstam, Henrik, 1975-
(författare)
-
The interdependence of plastic behaviour and final properties of steel wire, analysed by the finite element method
- 2004
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The finite element method (FEM) has been used in order to study the interdependence of plastic behaviour and final properties in steel wire. Three processes metal forming have been studied: billet forging, wire rod rolling, and cold drawing. The forging study focuses on the possibilities to eliminate voids, pores and pipes by altering the bite ratio in open die forging. Forging is used in wire manufacturing when dealing with materials that are difficult or impossible to roll, e.g. tool steels like high-speed steels, and powder metallurgically manufactured materials like tungsten-molybdenum filament wire. The elimination of inner defects by forging were successfully simulated by the FEM. The rolling study focuses on the problems due of the extreme finish rolling velocities in modern wire rod mills and modern technologies such as thermo-mechanical rolling and sizing. A design for a high-speed laboratory mill for studies of material behaviour at extreme strain rates was made. With a combination of two-high stands and three-roll units is it possible to obtain a smoother temperature distribution in the bar cross section. Two studies of the cold drawing process were made. The first describes the distribution of the plastic deformation due to the die geometry. It was found that the influence of the die angle on the amount of inhomogeneous deformation decreases with increasing area reduction. The frictional behaviour was also studied. The second study describes how the bearing geometry affects the residual stress-state in the wire. It was found that a small taper could change the residual stress state in the surface immensely. This was shown with FE simulations and verified by X-ray diffraction measurements. The results in this paper gives a tool for control of the residual stress-state in the wire. This gives a possibility to increase e.g. the fatigue strength in the final product.
|
|
| 2. |
- A Atlasov, Kirill, et al.
(författare)
-
1D photonic band formation and photon localization in finite-size photonic-crystal waveguides
- 2010
-
Ingår i: OPTICS EXPRESS. - 1094-4087. ; 18:1, s. 117-122
-
Tidskriftsartikel (refereegranskat)abstract
- A transition from discrete optical modes to 1D photonic bands is experimentally observed and numerically studied in planar photonic-crystal (PhC) L-N microcavities of length N. For increasing N the confined modes progressively acquire a well-defined momentum, eventually reconstructing the band dispersion of the corresponding waveguide. Furthermore, photon localization due to disorder is observed experimentally in the membrane PhCs using spatially resolved photoluminescence spectroscopy. Implications on single-photon sources and transfer lines based on quasi-1D PhC structures are discussed.
|
|
| 3. |
- A Herrera, I, et al.
(författare)
-
Comparing a multi-linear (STEP) and systemic (FRAM) method for accident analysis
- 2010
-
Ingår i: RELIABILITY ENGINEERING and SYSTEM SAFETY. - London, UK : Elsevier Science B.V., Amsterdam.. - 0951-8320. ; 95:12, s. 1269-1275, s. 19-26
-
Tidskriftsartikel (refereegranskat)abstract
- Accident models and analysis methods affect what accident investigators look for, which contributory factors are found, and which recommendations are issued. This paper contrasts the Sequentially Timed Events Plotting (STEP) method and the Functional Resonance Analysis Method (FRAM) for accident analysis and modelling. The main issue addressed in this paper is the comparison of the established multi-linear method STEP with the new systemic method FRAM and which new insights the latter provides for accident analysis in comparison to the former established multi-linear method. Since STEP and FRAM are based on a different understandings of the nature of accidents, the comparison of the methods focuses on what we can learn from both methods, how, when, and why to apply them. The main finding is that STEP helps to illustrate what happened, involving which actors at what time, whereas FRAM illustrates the dynamic interactions within socio-technical systems and lets the analyst understand the how and why by describing non-linear dependencies, performance conditions, variability, and their resonance across functions.
|
|
| 4. |
- Aalberg, L, et al.
(författare)
-
Development of a harmonised method for the profiling of amphetamines : II. Stability of impurities in organic solvents
- 2005
-
Ingår i: Forensic Science International. - : Elsevier. - 0379-0738 .- 1872-6283. ; 149:03-Feb, s. 231-241
-
Tidskriftsartikel (refereegranskat)abstract
- The present study focused on the stability of 22 amphetamine impurities dissolved in six organic solvents: isooctane, toluene, ethanol, dichloromethane, ethyl acetate, and diethyl ether. The aim was to find the most inert, and thereby most suitable, solvent for amphetamine profiling. Mixtures of the impurities were prepared in the different solvents, and changes in the concentrations of the individual compounds over-time were monitored by gas chromatographic analysis after 0, 4, 12, 24, 48, and 96 h. Isooctane and toluene provided the most inert conditions, although, a few of the impurities were insufficiently stable in these two solvents. The present experiments were performed as a part of the development of a harmonised method for profiling of amphetamine. The results can be used to support the choice of organic solvents for sample preparation. They also provide information about the stability of the impurities that are found in profiles of illicit amphetamine. This is essential due to the fact, that unstable compounds can have a negative influence on the comparison of profiles.
|
|
| 5. |
- Aarao, J, et al.
(författare)
-
Numerical implementation of the EDEM for modified Helmholtz BVPs on annular domains
- 2011
-
Ingår i: JOURNAL OF COMPUTATIONAL AND APPLIED MATHEMATICS. - : Elsevier Science B.V., Amsterdam.. - 0377-0427. ; 235:5, s. 1342-1353
-
Tidskriftsartikel (refereegranskat)abstract
- In a recent paper by the current authors a new methodology called the Extended-Domain-Eigenfunction-Method (EDEM) was proposed for solving elliptic boundary value problems on annular-like domains. In this paper we present and investigate one possible numerical algorithm to implement the EDEM. This algorithm is used to solve modified Helmholtz BVPs on annular-like domains. Two examples of annular-like domains are studied. The results and performance are compared with those of the well-known boundary element method (BEM). The high accuracy of the EDEM solutions and the superior efficiency of the EDEM over the BEM, make EDEM an excellent alternate candidate to use in the animation industry, where speed is a predominant requirement, and by the scientific community where accuracy is the paramount objective.
|
|
| 6. |
- Aarao, J, et al.
(författare)
-
The extended-domain-eigenfunction method for solving elliptic boundary value problems with annular domains
- 2010
-
Ingår i: JOURNAL OF PHYSICS A-MATHEMATICAL AND THEORETICAL. - : Iop. - 1751-8113 .- 1751-8121. ; 43:18, s. 185202-
-
Tidskriftsartikel (refereegranskat)abstract
- Standard analytical solutions to elliptic boundary value problems on asymmetric domains are rarely, if ever, obtainable. In this paper, we propose a solution technique wherein we embed the original domain into one with simple boundaries where the classical eigenfunction solution approach can be used. The solution in the larger domain, when restricted to the original domain, is then the solution of the original boundary value problem. We call this the extended-domain-eigenfunction method. To illustrate the methods strength and scope, we apply it to Laplaces equation on an annular-like domain.
|
|
| 7. |
- Aarnio, Harri, et al.
(författare)
-
Spontaneous Charge Transfer and Dipole Formation at the Interface Between P3HT and PCBM
- 2011
-
Ingår i: Advanced Energy Materials. - : Wiley-VCH Verlag Berlin. - 1614-6832 .- 1614-6840. ; 1:5, s. 792-797
-
Tidskriftsartikel (refereegranskat)abstract
- In the pursuit of developing new materials for more efficient bulk-heterojunction solar cells, the blend poly (3-hexylthiophene):[ 6,6]-phenyl-C(61)-butyric acid methyl ester (P3HT:PCBM) serves as an important model system. The success of the P3HT: PCBM blend comes from efficient charge generation and transport with low recombination. There is not, however, a good microscopic picture of what causes these, hindering the development of new material systems. In this report UV photoelectron spectroscopy measurements on both regiorandom-(rra) and regioregular-(rr) P3HT are presented, and the results are interpreted using the Integer Charge Transfer model. The results suggest that spontaneous charge transfer from P3HT to PCBM occurs after heat treatment of P3HT: PCBM blends. The resulting formation of an interfacial dipole creates an extra barrier at the interface explaining the reduced (non-)geminate recombination with increased charge generation in heat treated rr-P3HT: PCBM blends. Extensive photoinduced absorption measurements using both above-and below-bandgap excitation light are presented, in good agreement with the suggested dipole formation.
|
|
| 8. |
- Aasmundtveit, K.E., et al.
(författare)
-
Structural anisotropy of poly(alkylthiophene) films
- 2000
-
Ingår i: Macromolecules. - : American Chemical Society (ACS). - 0024-9297 .- 1520-5835. ; 33:8, s. 3120-3127
-
Tidskriftsartikel (refereegranskat)abstract
- The structural anisotropy of various poly(alkylthiophene) films have been studied by X-ray diffraction, using both conventional methods and synchrotron radiation at grazing incidence. Solution-cast films orient with the side chains preferably normal to the film surface, whereas spin-cast films of nonstereoregular material orient with both the main and the side chains in the film plane. For thick (10-50 µm) solution-cast films, the degree of orientation depends strongly on the solvent used for casting, and on the stereoregularity of the polymer, films of stereoregular materials being more oriented than those of nonregular materials. The most oriented nonregular films are those cast from mixtures of chloroform and tetrahydrofuran. Thin (50-500 nm) solution-cast films are more oriented than the thicker ones, and the effects of different stereoregularity or different casting solvents are small. For spin-cast films, the degree of orientation is independent of substrate and solvent. Spin-cast films of stereoregular material have two different phases: One with the side chains normal to the substrate, and another where they are parallel to the substrate. The diffraction peaks of spin-cast poly(octylthiophene) narrow considerably upon heating.
|
|
| 9. |
- Aasmundtveit, K.E., et al.
(författare)
-
Structural aspects of electrochemical doping and dedoping of poly(3,4-ethylenedioxythiophene)
- 2000
-
Ingår i: Synthetic metals. - 0379-6779 .- 1879-3290. ; 113:1, s. 93-97
-
Tidskriftsartikel (refereegranskat)abstract
- Electrochemical dedoping and redoping of p-toluene sulfonate doped poly(3,4-ethylenedioxythiophene) (PEDOT) has been studied with in situ grazing incidence diffraction with water used as an electrolyte. The diffraction peak positions and integrated intensities do not change significantly during doping and dedoping, while the peak widths increase upon dedoping and decrease upon doping. This implies that the lattice parameters and the relative positions of the polymer chains and the p-toluene sulfonate ions remain unchanged, the redox processes being carried out by the motion of smaller ions between the polymer and the electrolyte, and that the structural order decreases upon dedoping and increases upon doping in a reversible manner.
|
|
| 10. |
- Aasmundtveit, K.E., et al.
(författare)
-
Structural ordering in phenyl-substituted polythiophenes
- 2000
-
Ingår i: Macromolecules. - : American Chemical Society (ACS). - 0024-9297 .- 1520-5835. ; 33:15, s. 5481-5489
-
Tidskriftsartikel (refereegranskat)abstract
- Various substituted poly(phenylthiophene)s have been studied by X-ray diffraction. They are semicrystalline, with very different degrees of crystallinity. Those with para-substituted phenyl groups have a low degree of crystallinity, whereas those with ortho-substituted phenyl groups are more crystalline. The most crystalline materials in this study have two equally long substituents on the phenyl ring, one at the ortho position and the other at the ortho or meta position on the opposite side of the phenyl ring. Poly(3-(2,5-dioctylphenyl)thiophene) (PDOPT) was most thoroughly studied, and a structural model is proposed. The structure of PDOPT is quite different from previously studied substituted polythiophenes in that the octyl side chains are directed normal to the thiophene planes. In this way, the conjugated polymer chains are kept separated from each other. Solution-cast and spin-cast PDOPT films are anisotropic, with the octyl side chains oriented normal to the film surface in both cases. This is contrary to the situation for poly(3-alkylthiophene)s, where solution-cast and spin-cast films orient in different ways.
|
|
| 11. |
- Aavikko, R, et al.
(författare)
-
Observation of vacancy clusters in HTCVD grown SiC
- 2005
-
Ingår i: Materials Science Forum, Vols. 483-485. ; , s. 469-472
-
Konferensbidrag (refereegranskat)abstract
- Positron lifetime spectroscopy was used to study defects in semi-insulating (SI) silicon carbide (SiC) substrates grown by high-temperature chemical vapor deposition (HTCVD). The measured positron lifetime spectra can be decomposed into two components, of which the longer corresponds to vacancy clusters. We have carried out atomic superposition calculations to estimate the size of these clusters.
|
|
| 12. |
- Aazh, H, et al.
(författare)
-
Influence of ear canal occlusion and static pressure difference on bone conduction thresholds: Implications for mechanisms of bone conduction
- 2005
-
Ingår i: International Journal of Audiology. - : Informa Healthcare. - 1499-2027 .- 1708-8186. ; 44:5, s. 302-306
-
Tidskriftsartikel (refereegranskat)abstract
- The effect of air pressure change on bone conduction (BC) hearing thresholds in the occluded ear was investigated. The pump manometer system of an impedance bridge was used to change the air pressure in the ear canal of twenty-two normally hearing subjects. BC thresholds were measured with: (1) open ear; (2) the ear canal occluded with a probe tube and application of 0 daPa air pressure; and (3) the ear canal occluded with a probe tube and application of -350 daPa air pressure. Thresholds were lower in condition 2 than in condition 1, the difference decreasing from 27 dB at 2500 Hz to 4.5 dB at 2000 Hz. Thresholds were higher in condition 3 than in condition 2. The results are interpreted in terms of changes in the relative contribution of the three routes of transmission for BC sound produced by occlusion and by a static pressure difference.
|
|
| 13. |
- Abad, Manuel David, et al.
(författare)
-
Identification of Ternary Phases in TiBC/a-C Nanocomposite Thin Films : Influence on the Electrical and Optical Properties
- 2011
-
Ingår i: Plasma Processes and Polymers. - : Wiley. - 1612-8850 .- 1612-8869. ; 8:7, s. 579-588
-
Tidskriftsartikel (refereegranskat)abstract
- The local structure of TiBC and amorphous carbon (a-C) nanocomposite films (TiBC/a-C) was correlated with their optical and electrical properties. TiBC/a-C films with increasing C content were deposited by magnetron co-sputtering from TiC:TiB(2) (60: 40) and graphite targets. Chemical composition is determined by electron energy-loss spectroscopy. Grazing incidence X-ray diffraction reveals that the microstructure of the films is amorphous with small nanocrystallites emerging by increasing the C content that could be attributed to the formation of ternary (TiB(x)C(y)) or mixed binary (TiB(2) and TiC) phases. Further information was then obtained by studying the chemical bonding by measuring the near-edge fine structure (NES) by electron energy-loss (B K-, C K-, and Ti L-edges) and X-ray absorption (B K-and Ti L-edges) spectroscopies. The NES analysis indicates the formation of a nanocrystalline ternary TiB(x)C(y) compound concomitant with the segregation of an a-C phase as the carbon content is increased. The optical properties were studied by spectroscopic ellipsometry and the electrical resistivity was measured by the Van der Pauw method between 20 and 300 K. The films continuously lose their metallic character in terms of optical constants and resistivity with increasing carbon content. Theoretical fitting of the electrical properties using the grain-boundary scattering model supported the formation of a nanocomposite structure based on a ternary TiB(x)C(y) phase embedded in a matrix of a-C. The electron transport properties are mainly limited by the high density of point defects, grain size, and transmission probability.
|
|
| 14. |
- Abadei, S., et al.
(författare)
-
Microwave properties of tunable capacitors basee on magnetron sputtered ferroelectric Na0.5K0.5NbO3 film on low and high resistivity silicon substrates
- 2001
-
Ingår i: Integrated Ferroelectrics. - : Informa UK Limited. - 1058-4587 .- 1607-8489. ; 39:1-4, s. 359-366
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- In this work, small signal DC voltage dependent dielectric permittivity, loss tangent, and tuneability of magnetron sputtered epitaxial Na0.5K0.5NO3 films are studied experimentally. (100)-oriented Na0.5K0.5NbO3 films are deposited onto SiO2-buffered CMOS grade low resistivity (p = 10-20 cm) and high resistivity (p = 15-45 kcm) silicon substrates. Planar capacitors with 2 or 4 m gaps between electrodes have been fabricated on top of ferroelectric films. These devices have been characterized in the frequency range 1.0 MHz to 50 GHz at temperatures 30 - 300K. Na0.5K0.5NbO3/SiO2/Si structures on high resistivity silicon substrate exhibit C-V performances typical for Metal-Insulator- Semiconductor (MIS) capacitors. At low frequencies, f 1.0 GHz, the large tuneability and large losses are associated with the MIS structure, while at higher microwave frequencies the tuneability is mainly associated with the ferroelectric, film. At 1.0 MHz and room temperature, the tuneability of Na0.5K0.5NbO3/SiO2/Si structures more than 90%, reducing to 10-15 % at 50 GHz. The losses decrease with increasing the DC bias and frequency. A Q-factor more than 15 at 50 GHz is observed. The dielectric permittivity of the Na0.5K0.5NbO3 film is in the range 50-150 at frequencies 0.045-50 GHz. On low resistivity substrate the performance of Na0.5K0.5NbO3 films is completely screened by the high losses in silicon, and the tuneability is negligible. © 2001 Taylor and Francis.
|
|
| 15. |
- Abbas, Ghazanfar, et al.
(författare)
-
Preparation and Characterization of Nanocomposite Calcium Doped Ceria Electrolyte With Alkali Carbonates (NK-CDC) for SOFC
- 2011
-
Ingår i: Journal of Fuel Cell Science and Technology. - : ASME International. - 1550-624X .- 1551-6989. ; 8:4, s. 041013-
-
Tidskriftsartikel (refereegranskat)abstract
- The entire world's challenge is to find out the renewable energy sources due to rapid depletion of fossil fuels because of their high consumption. Solid oxide fuel cells (SOFCs) are believed to be the best alternative source, which converts chemical energy into electricity without combustion. Nanostructure study is required to develop highly ionic conductive electrolytes for SOFCs. In this work, the calcium doped ceria (Ce0.8Ca0.2O1.9) coated with 20% molar ratio of two alkali carbonates (CDC-M: MCO3, where M = Na and K) electrolyte was prepared by coprecipitation method. Ni based electrode was used to fabricate the cell by dry pressing technique. The crystal structure and surface morphology were characterized by an X-ray diffractometer, scanning electron microscopy (SEM), and high resolution transmission electron microscopy (TEM). The particle size was calculated in the range 10-20 nm by Scherer's formula and compared with SEM and TEM results. The ionic conductivity was measured by using ac electrochemical impedance spectroscopy method. The activation energy was also evaluated. The performance of the cell was measured 0.567 W/cm(2) at temperature 550 degrees C with hydrogen as a fuel.
|
|
| 16. |
- Abbas, Muhammad, et al.
(författare)
-
Comparison of Multiplierless Implementation of Nonlinear-Phase Versus Linear-Phase FIR filters
- 2008
-
Konferensbidrag (refereegranskat)abstract
- FIR filters are often used because of their linear-phase response. However, there are certain applications where the linear-phase property is not required, such as signal energy estimation, but IIR filters can not be used due to the limitation of sample rate imposed by the recursive algorithm. In this work, we discuss multiplierless implementation of minimum order, and therefore nonlinear-phase, FIR filters and compare it to the linear-phase counterpart.
|
|
| 17. |
- Abbas, Muhammad, et al.
(författare)
-
Low-Complexity Parallel Evaluation of Powers Exploiting Bit-Level Redundancy
- 2010
-
Ingår i: Conference Record of the Forty Fourth Asilomar Conference on Signals, Systems and Computers (ASILOMAR), 2010, 7-10 Nov. 2010. - Washington, DC, USA : IEEE Computer Society. - 9781424497225 ; , s. 1168-1172
-
Konferensbidrag (refereegranskat)abstract
- In this work, we investigate the problem of computing any requested set of power terms in parallel using summations trees. This problem occurs in applications like polynomial approximation, Farrow filters (polynomial evaluation part) etc. In the proposed technique, the partial product of each power term is initially computed independently. A redundancy check is then made in each and among all partial products matrices at bit level. The redundancy here relates to the fact that same three partial products may be present in more than one columns, and, hence, can be mapped to the same full adder. The proposed algorithm is tested for different sets of powers and wordlengths to exploit the sharing potential.
|
|
| 18. |
- Abbas, Muhammad, et al.
(författare)
-
On the Fixed-Point Implementation of Fractional-Delay Filters Based on the Farrow Structure
- 2013
-
Ingår i: IEEE Transactions on Circuits and Systems Part 1. - : Institute of Electrical and Electronics Engineers (IEEE). - 1549-8328 .- 1558-0806. ; 60:4, s. 926-937
-
Tidskriftsartikel (refereegranskat)abstract
- In this paper, the fixed-point implementation of adjustable fractional-delay filters using the Farrow structure is considered. Based on the observation that the sub-filters approximate differentiators, closed-form expressions for the L-2-norm scaling values at the outputs of each sub-filter as well as at the inputs of each delay multiplier are derived. The scaling values can then be used to derive suitable word lengths by also considering the round-off noise analysis and optimization. Different approaches are proposed to derive suitable word lengths including one based on integer linear programming, which always gives an optimal allocation. Finally, a new approach for multiplierless implementation of the sub-filters in the Farrow structure is suggested. This is shown to reduce register complexity and, for most word lengths, require less number of adders and subtracters when compared to existing approaches.
|
|
| 19. |
- Abbas, Muhammad, et al.
(författare)
-
Power Estimation of Recursive and Non-Recursive CIC Filters Implemented in Deep-Submicron Technology
- 2010
-
Ingår i: Proceedings of International Conference on Green Circuits and Systems (ICGCS), 2010, Date: 21-23 June, 2010. - : IEEE. - 9781424468775 - 9781424468768 ; , s. 221-225
-
Konferensbidrag (refereegranskat)abstract
- The power modeling of different realizations of cascaded integrator-comb (CIC) decimation filters has been a subject of several recent works. In this work we have extended these with modeling of leakage power, which is an important factor since the input sample rate may differ several orders of magnitude. Furthermore, we have pointed out the importance of the input wordlength on the comparison of recursive and nonrecursive implementations.
|
|
| 20. |
- Abbas, Muhammad, et al.
(författare)
-
Switching Activity Estimation of CIC Filter Integrators
- 2010
-
Ingår i: Proceedings of Asia Pacific Conference on Postgraduate Research in Microelectronics and Electronics (PrimeAsia), 2010, Date:22-24 Sept. 2010. - : IEEE. - 9781424467365 - 9781424467358 ; , s. 21-24
-
Konferensbidrag (refereegranskat)abstract
- In this work, a method for estimation of the switching activity in integrators is presented. To achieve low power, it is always necessary to develop accurate and efficient methods to estimate the switching activity. The switching activities are then used to estimate the power consumption. In our work, the switching activity is first estimated for the general purpose integrators and then it is extended for the estimation of switching activity in cascaded integrators in CIC filters.
|
|
| 21. |
- Abbasi, Mazhar Ali, et al.
(författare)
-
Anions effect on the low temperature growth of ZnO nanostructures
- 2012
-
Ingår i: Vacuum. - : Elsevier. - 0042-207X .- 1879-2715. ; 86:12, s. 1998-2001
-
Tidskriftsartikel (refereegranskat)abstract
- Seed mediated aqueous chemical growth (ACG) route was used for the growth of ZnO nanostructures on Si substrate in four different growth mediums. The growth medium has shown to affect the morphology and the size of the different nanostructures. We observed that the medium containing zinc nitrate anions yields the nanorods, in a medium containing zinc acetate anions nano-candles are obtained. While in a medium containing zinc chloride anions ZnO nano-discs were obtained and in a medium containing zinc sulfate anions nano-flakes are achieved. Growth in these different mediums has also shown effect on the optical emission characteristics of the different ZnO nanostructures.
|
|
| 22. |
- Abbasi, Mazhar Ali, et al.
(författare)
-
Fabrication of UV photo-detector based on coral reef like p-NiO/n-ZnO nanocomposite structures
- 2013
-
Ingår i: Materials letters (General ed.). - : Elsevier. - 0167-577X .- 1873-4979. ; 108, s. 149-152
-
Tidskriftsartikel (refereegranskat)abstract
- In this research work, a UV photo-detector is fabricated on fluorine doped tin oxide (FTO) glass substrate by exploiting the advantageous features of p-n heterojunctions based on p-NiO and n-ZnO composite nanostructures forming a coral-reef like structures. Scanning electron microscopy (SEM) and X-ray diffraction results showed uniform morphology and good crystal quality of the synthesised nanostructures respectively. I-V measurements have shown nonlinear and rectifying response of the p-NiO/n-ZnO heterojunction. The proposed photodiode exhibited excellent UV response with acceptable photocurrent generation of about 3.4 mA and the responsivity of 2.27 A/W at -3 biasing voltage.
|
|
| 23. |
- Abbasi, Mazhar Ali, et al.
(författare)
-
Iron (III) Ion Sensor Based on the Seedless Grown ZnO Nanorods in 3 Dimensions Using Nickel Foam Substrate
- 2013
-
Ingår i: Journal of Sensors. - : Hindawi Publishing Corporation. - 1687-725X .- 1687-7268. ; :382726
-
Tidskriftsartikel (refereegranskat)abstract
- In the present work, the seedless, highly aligned and vertical ZnO nanorods in 3 dimensions (3D) were grown on the nickel foam substrate. The seedless grown ZnO nanorods were characterised by field emission scanning electron microscopy (FESEM), high resolution transmission electron microscopy (HRTEM), and X-ray diffraction (XRD) techniques. The characterised seedless ZnO nanorods in 3D on nickel foam were highly dense, perpendicular to substrate, grown along the (002) crystal plane, and also composed of single crystal. In addition to this, these seedless ZnO nanorods were functionalized with trans-dinitro-dibenzo-18-6 crown ether, a selective iron (III) ion ionophore, along with other components of membrane composition such as polyvinyl chloride (PVC), 2-nitopentylphenyl ether as plasticizer (NPPE), and tetrabutyl ammonium tetraphenylborate (TBATPB) as conductivity increaser. The sensor electrode has shown high linearity with a wide range of detection of iron (III) ion concentrations from 0.005 mM to 100 mM. The low limit of detection of the proposed ion selective electrode was found to be 0.001 mM. The proposed sensor also described high storage stability, selectivity, reproducibility, and repeatability and a quick response time of less than 10 s.
|
|
| 24. |
- Abbasi, Mazhar Ali, et al.
(författare)
-
Potentiometric Zinc Ion Sensor Based on Honeycomb-Like NiO Nanostructures
- 2012
-
Ingår i: Sensors. - : MDPI. - 1424-8220. ; 12:11, s. 15424-15437
-
Tidskriftsartikel (refereegranskat)abstract
- In this study honeycomb-like NiO nanostructures were grown on nickel foam by a simple hydrothermal growth method. The NiO nanostructures were characterized by field emission electron microscopy (FESEM), high resolution transmission electron microscopy (HRTEM) and X-ray diffraction (XRD) techniques. The characterized NiO nanostructures were uniform, dense and polycrystalline in the crystal phase. In addition to this, the NiO nanostructures were used in the development of a zinc ion sensor electrode by functionalization with the highly selective zinc ion ionophore 12-crown-4. The developed zinc ion sensor electrode has shown a good linear potentiometric response for a wide range of zinc ion concentrations, ranging from 0.001 mM to 100 mM, with sensitivity of 36 mV/decade. The detection limit of the present zinc ion sensor was found to be 0.0005 mM and it also displays a fast response time of less than 10 s. The proposed zinc ion sensor electrode has also shown good reproducibility, repeatability, storage stability and selectivity. The zinc ion sensor based on the functionalized NiO nanostructures was also used as indicator electrode in potentiometric titrations and it has demonstrated an acceptable stoichiometric relationship for the determination of zinc ion in unknown samples. The NiO nanostructures-based zinc ion sensor has potential for analysing zinc ion in various industrial, clinical and other real samples.
|
|
| 25. |
- Abdo, A. A., et al.
(författare)
-
A change in the optical polarization associated with a gamma-ray flare in the blazar 3C 279
- 2010
-
Ingår i: Nature. - : Springer Science and Business Media LLC. - 0028-0836 .- 1476-4687. ; 463:7283, s. 919-923
-
Tidskriftsartikel (refereegranskat)abstract
- It is widely accepted that strong and variable radiation detected over all accessible energy bands in a number of active galaxies arises from a relativistic, Doppler-boosted jet pointing close to our line of sight(1). The size of the emitting zone and the location of this region relative to the central supermassive black hole are, however, poorly known, with estimates ranging from light-hours to a light-year or more. Here we report the coincidence of a gamma (gamma)-ray flare with a dramatic change of optical polarization angle. This provides evidence for co-spatiality of optical and gamma-ray emission regions and indicates a highly ordered jet magnetic field. The results also require a non-axisymmetric structure of the emission zone, implying a curved trajectory for the emitting material within the jet, with the dissipation region located at a considerable distance from the black hole, at about 10(5) gravitational radii.
|
|
