1. |
- Akbarpour, Sahar, 1980-
(author)
-
Enhanced Composite Joint Performance through Interlacement of Metal Inserts
- 2021
-
Doctoral thesis (other academic/artistic)abstract
- The work in this thesis investigates bolted joints in fibre reinforced composites with particular focus on a novel insert concept. The concept is characterised by replacing all composite plies with stacked metal patches, locally around a bolt hole, so that they jointly form a solid metal reinforcement. An extensive experimental study is presented together with finite element analysis of the studied cases.Reinforcing bolt holes with high-strength metals improves the bearing load capacity of the composite laminates. True enhancement of the joint performance however requires that the open-hole tensile strength is improved as well. The work started with tests of pin-loaded and open-hole tensile specimens with inserts, and significant improvement of the bearing load capacity was found. The initial tests enabled more informed design, and insert configurations having sufficient open-hole tensile strength could thereby be manufactured and tested. In parallel, composite-metal joints were numerically modelled to simulate and analyse the mechanical performance of the joints and gain a better understanding of the governing damage mechanisms.The performance of the joints was eventually investigated by means of experiments on single-shear, single- and double-bolt specimens, with and without inserts. The allowable bolt distance and the influence from the bolt tightening torque were also examined.The initial samples had inserts of stainless steel. Later, specimens with titanium alloy inserts were also included in the test series. Various insert configurations were designed to study the effects of different features in the composite-metal bond lines. The numerical simulations of the composite--metal interfaces were performed with two types of models, one joining the two materials directly to each other, without modelling any adhesive film in between, and the other including an elastic representation of the adhesive layer. The experimental results were then used to support verification of the results from the simulations.The final assessment of the concept was performed on insert configurations designed either for pure tensile loading or for more general (bi-directional) loading conditions, and the bearing load capacity, open-hole tensile strength and the performance of bolted joints were compared for cases with different inserts. While higher bearing strength improvement was achieved when the holes were reinforced with inserts of stainless steel, reinforcement with inserts of titanium was even more successful since it improved virtually all studied aspects of the joints considerably.
|
|
2. |
- Akbarpour, Sahar, et al.
(author)
-
Enhancing the performance of bolted joints in composites by use of patched steel or titanium inserts
- 2021
-
Reports (other academic/artistic)abstract
- A new insert concept that interlaces metal inserts into composite laminates has earlier been shown to improve the relatively poor bearing strength of holes in fibre reinforced polymer composites, and it is here further and more thoroughly investigated. The concept was invented to increase the efficiency of joints with mechanical fasteners in composite materials and this work presents experiments on double bolt joints with inserts made of either stainless steel or a titanium (Ti) alloy. In particular the work compares different implementations of the insert concept by reinforcing one or two holes in double bolt joints, and the effect of using different metals in the inserts. Some complementary tests on pin-loaded specimens and open hole tensile specimens are also performed and compared, also with some results reported previously. Considerable improvements in the bearing load capacity, i.e. 50%-60% or 35%-45%, is attained. The open-hole tensile strength is also improved considerably (almost 30%) when the holes are reinforced with Ti inserts. The fact that the inserts can improve not only the bearing strength but also the performance in open-hole tension implies that the Ti inserts bring nothing but positive effects to the strength of the joints. The test results from single-shear double-bolt specimens with inserts at one hole showed improved strengths of 30% and 20% for specimens with steel and Ti inserts, respectively. Finally, an impressive strength improvement of 40-45% is achieved for single-shear double-bolt specimens having both holes reinforced with inserts of either steel or Ti.
|
|
3. |
- Akbarpour, Sahar, et al.
(author)
-
Enhancing the performance of bolted joints in composites by use of patched steel or titanium inserts
- 2021
-
In: Composite structures. - : Elsevier BV. - 0263-8223 .- 1879-1085. ; 275
-
Journal article (peer-reviewed)abstract
- A new insert concept that interlaces metal inserts into composite laminates has earlier been shown to improve the relatively poor bearing strength of holes in fibre reinforced polymer composites, and it is here further and more thoroughly investigated. The concept was invented to increase the efficiency of joints with mechanical fasteners in composite materials and this work presents experiments on double-bolt joints with inserts made of either stainless steel or a titanium (Ti) alloy. In particular the work compares different implementations of the insert concept by reinforcing one or two holes in double bolt joints, and the effect of using different metals in the inserts. Some complementary tests on pin-loaded specimens and open hole tensile specimens are also performed and compared, partly with results that were reported previously. Considerable improvements of the bearing load capacity are attained, i.e. 50%-60% for steel and 35%-45% for Ti, compared to references. The open-hole tensile strength is also improved considerably (almost 30%) when the holes are reinforced with Ti inserts. The fact that the inserts can improve not only the bearing strength but also the performance in open-hole tension implies that the Ti inserts bring nothing but positive effects to the strength of the joints. The test results from single-shear double-bolt specimens with inserts at one hole showed improved strengths of 30% and 20% for specimens with steel and Ti inserts, respectively. Finally, an impressive strength improvement of 40-45% is achieved for single-shear double-bolt specimens having both holes reinforced with inserts of either steel or Ti.
|
|
4. |
- Akbarpour, Sahar, et al.
(author)
-
Experimental investigation and numerical analysis of multi-material interfaces related to a composite joint concept
- 2021
-
Reports (other academic/artistic)abstract
- An insert concept for reinforcing bolt-holes with high strength metals was previously introduced by the authors, where inserts are anchored in composite laminates through interlacement of composite plies and thin metal patches. The resulting finger-joints must be strong enough to avoid composite-metal debonding happening before bearing failure at the bolt-hole. The strength of the composite-metal interfaces is thus crucial for successful implementation of the insert concept. The paper presents an experimental study investigating the strength of various interface geometries between a prepreg composite material and stainless steel or titanium alloy inserts. In addition to the experimental work, finite element simulations are performed to analyse the stresses at the interfaces. The results indicate that the stress concentrations at multi-material corner points govern the failure and that the strength can be enhanced by expedient design.
|
|
5. |
- Akbarpour, Sahar, et al.
(author)
-
Reinforcement around holes in composite materials by use of patched metal inserts
- 2019
-
In: Composite structures. - : Elsevier. - 0263-8223 .- 1879-1085. ; 225
-
Journal article (peer-reviewed)abstract
- Metal inserts are sometimes used to improve the load carrying capacity of bolted joints in composite materials. In this paper a new concept is introduced where inserts are built during composite manufacturing by integrating stacked metal patches at locations where holes are to be made after consolidation. Initial tests and a parameter study enable more informed design, and specimens with improved stacked inserts are then produced and tested. The specimens with inserts show up to 60% strength improvement in pin-loaded tests. In addition to the experimental work, finite element analysis is performed to investigate the stress fields and the failure mechanisms. The model indicates that the singular stresses at the multi-material corner points are governing for the strength and give indications of the failure mechanisms. Some basic analytical estimates are also presented.
|
|
6. |
- Akbarpour, Sahar, et al.
(author)
-
Strength improvement of bolted joints in composite materials by use of patched metal inserts
- 2020
-
In: Composite structures. - : Elsevier BV. - 0263-8223 .- 1879-1085. ; 52
-
Journal article (peer-reviewed)abstract
- Metal inserts are occasionally used to improve bearing load capacity of bolted joints in laminated composite materials. This paper investigates a new reinforcement concept where inserts are built by locally replacing composite plies with metal patches of various diameters, surrounding the holes. The inserts are built during composite manufacturing by alternately placing the metal patches through the thickness of the laminate at locations where holes are to be drilled after consolidation. An extensive experimental study including pin‐ loaded, open–hole tensile, and single‐shear testing of bolted specimens is presented. Considerable improve- ment of the bearing strength – 50‐60% – is attained for pin‐loaded specimens with inserts, demonstrating the potential of the reinforcement concept. The open–hole tensile tests show that the by‐pass strength can be maintained or even improved with up to 20% if the inserts are properly designed. Finally, the results from the single‐shear tests of bolted joints show more than 25% improvement in strength for reinforced single‐ and double‐bolt specimens. It is possible that the inserts would maintain clamping pressure over time, which could then almost double the imrovement (47%) for bolted joints.
|
|
7. |
- Bull, Peter Hoaas, et al.
(author)
-
Curved sandwich beams with face-core debond subjected to bending moment
- 2004
-
In: Journal of Sandwich Structures and Materials. - : SAGE Publications. - 1099-6362 .- 1530-7972. ; 6:2, s. 115-127
-
Journal article (peer-reviewed)abstract
- Curved sandwich beams subjected to opening bending moment are studied. Face-core debonds of varying size are introduced at the compressively loaded face sheet and the structural integrity is investigated. Analytical and finite element models are compared in order to identify the governing failure modes of the beams. A simple expression is presented as a tool for getting a quick estimate of the severity of an interface crack in a curved sandwich beam. Five different configurations of beams are tested experimentally in a custom made bending rig.
|
|
8. |
- Bull, Peter Hoaas, et al.
(author)
-
High-velocity and quasi-static impact of large sandwich panels
- 2004
-
In: Journal of Sandwich Structures and Materials. - : Sage Publications. - 1099-6362 .- 1530-7972. ; 6:2, s. 97-113
-
Journal article (peer-reviewed)abstract
- An investigation of the response of sandwich structures subjected to impact velocities of virtually 0 m/s and approximately 1000 m/s is conducted. The higher velocity exceeds both the longitudinal and the transverse wave propagation velocities of the core material in the sandwich panels. The objective is to investigate the possibility to simulate the damage from ballistic impact of sandwich panels through quasi-static experiments. Panels are impacted using a 40 mm Bofors AA gun and, using a similar projectile, other panels are indented quasi-statically. Energy absorption is measured in both test series. After impact, the panels are tested in in-plane compression together with one undamaged panel for reference. Residual strength of impacted panels is analyzed by finite element analysis. It is shown that the damage from high-velocity impact is limited, and it is possible to regain most of the undamaged strength by repair.
|
|
9. |
|
|
10. |
|
|