| 1. |
- Rögnvaldsson, Thorsteinn, 1963-, et al.
(author)
-
ARC13 – Assessment of Research and Coproduction : Reports from the assessment of all research at Halmstad University 2013
- 2014
-
Reports (pop. science, debate, etc.)abstract
- During 2013, an evaluation of all the research conducted at Halmstad University was carried out. The purpose was to assess the quality of the research, coproduction, and collaboration in research, as well as the impact of the research. The evaluation was dubbed the Assessment of Research and Coproduction 2013, or ARC13. (Extract from Executive Summary)
|
|
| 2. |
- Akbari-Saatlu, Mehdi, et al.
(author)
-
H2S gas sensing based on SnO2thin films deposited by ultrasonic spray pyrolysis on Al2O3substrate
- 2021
-
In: 2021 IEEE Sensors Applications Symposium (SAS). - 9781728194318
-
Conference paper (peer-reviewed)abstract
- H2S gas is harmful for human health and environment, therefore novel gas sensors for real time and fast detection with high precision have been sought. Metal oxides are already known as promising candidate for this purpose. This article presents the performance of a gas sensor consists of a microheater and active layer formed on single alumina substrate for operating at high temperature applications. Ultrasonic spray pyrolysis deposition method was used to make both thick layer of SnO2 for microheater and thin and porous crystalline layer of SnO2 as sensing layer. The prepared sensor showed suitable dynamic response towards 10 to 50 ppm of H2S gas both in humid and dry conditions at 450 °C. In these experiments, the cross sensitivity of the sensor was also checked for other interfering gases e.g. CH4 and NO2.
|
|
| 3. |
- Akbari-Saatlu, Mehdi, et al.
(author)
-
Nanometer-Thick ZnO/SnO2Heterostructures Grown on Alumina for H2S Sensing
- 2022
-
In: ACS Applied Nano Materials. - : American Chemical Society (ACS). - 2574-0970. ; 5:5, s. 6954-6963
-
Journal article (peer-reviewed)abstract
- Designing heterostructure materials at the nanoscale is a well-known method to enhance gas sensing performance. In this study, a mixed solution of zinc chloride and tin (II) chloride dihydrate, dissolved in ethanol solvent, was used as the initial precursor for depositing the sensing layer on alumina substrates using the ultrasonic spray pyrolysis (USP) method. Several ZnO/SnO2 heterostructures were grown by applying different ratios in the initial precursors. These heterostructures were used as active materials for the sensing of H2S gas molecules. The results revealed that an increase in the zinc chloride in the USP precursor alters the H2S sensitivity of the sensor. The optimal working temperature was found to be 450 °C. The sensor, containing 5:1 (ZnCl2: SnCl2·2H2O) ratio in the USP precursor, demonstrates a higher response than the pure SnO2 (∼95 times) sample and other heterostructures. Later, the selectivity of the ZnO/SnO2 heterostructures toward 5 ppm NO2, 200 ppm methanol, and 100 ppm of CH4, acetone, and ethanol was also examined. The gas sensing mechanism of the ZnO/SnO2 was analyzed and the remarkably enhanced gas-sensing performance was mainly attributed to the heterostructure formation between ZnO and SnO2. The synthesized materials were also analyzed by X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray, transmission electron microscopy, and X-ray photoelectron spectra to investigate the material distribution, grain size, and material quality of ZnO/SnO2 heterostructures.
|
|
| 4. |
- Akbari-Saatlu, Mehdi, et al.
(author)
-
Silicon Nanowires for Gas Sensing : A Review
- 2020
-
In: Nanomaterials. - : MDPI AG. - 2079-4991. ; 10:11
-
Research review (peer-reviewed)abstract
- The unique electronic properties of semiconductor nanowires, in particular silicon nanowires (SiNWs), are attractive for the label-free, real-time, and sensitive detection of various gases. Therefore, over the past two decades, extensive efforts have been made to study the gas sensing function of NWs. This review article presents the recent developments related to the applications of SiNWs for gas sensing. The content begins with the two basic synthesis approaches (top-down and bottom-up) whereby the advantages and disadvantages of each approach have been discussed. Afterwards, the basic sensing mechanism of SiNWs for both resistor and field effect transistor designs have been briefly described whereby the sensitivity and selectivity to gases after different functionalization methods have been further presented. In the final words, the challenges and future opportunities of SiNWs for gas sensing have been discussed.
|
|
| 5. |
- Ashraf, Shakeel, 1984-, et al.
(author)
-
Determination of complex refractive index of SU-8 by Kramers-Kronig dispersion relation method at the wavelength range 2.5 – 22.0 μm
- 2019
-
In: Journal of Quantitative Spectroscopy and Radiative Transfer. - : Elsevier BV. - 0022-4073 .- 1879-1352. ; 224, s. 309-311
-
Journal article (peer-reviewed)abstract
- Accurate determination of the complex refractive index of SU-8 epoxy has significant for the wide variety of applications in optical sensor technology at IR range. The complex refractive index of SU-8 is determined by recording the transmission of light spectra for the wavelength range of 2.5 – 22.0 μm. The data analysis is based on the Kramers-Kronig dispersion relation method. The method has several merits, such as ease of operation, non-contact technique, measurement accuracy, and rapid measurement. The present method is not restricted to the case of SU-8 but it is also proposed to be applicable across a broad range of applications, such as assessment of the optical properties of paints and biomedical samples.
|
|
| 6. |
- Ashraf, Shakeel, 1984-, et al.
(author)
-
Evaluation of a CO2 sensitive thermopile with an integrated multilayered infrared absorber by using a long path length NDIR platform
- 2018
-
In: I2MTC 2018 - 2018 IEEE International Instrumentation and Measurement Technology Conference. - : IEEE. - 9781538622223 ; , s. 1-6
-
Conference paper (peer-reviewed)abstract
- In this work, a mid-infrared-sensitive thermopile detector was evaluated for carbon dioxide gas. The thermopile has an integrated absorber structure that has more than 95% absorption for the wavelength range of 3.3-5.5 μm. For the measurement of carbon dioxide, the detector was initially assembled on a small printed circuit board holder and then installed in a long path length non-dispersive infrared platform. The measurement setup was calibrated by exposing the detector to carbon dioxide of known concentrations (from 50 ppm to 1,300 ppm) and measuring the corresponding voltage response of the detector. The measured voltage values allowed us to calculate the calibration constant for this detector. This was followed by a verification process using a concentration of 500 ppm (which was not used in the calibration) and a known value of 1,300 ppm. The verification results matched with real values, demonstrating that the sensor can be used for highly sensitive and accurate carbon dioxide measurements at concentrations from a few ppm level up to 1,300 ppm. Above this level, additional calibration is needed.
|
|
| 7. |
- Ashraf, Shakeel, 1984-, et al.
(author)
-
Fabrication and characterization of a SU8-epoxy membrane based thermopile detector with an integrated multilayered absorber structure for the mid-IR region
- 2019
-
In: IEEE Sensors Journal. - 1530-437X .- 1558-1748. ; 19:11, s. 4000-4007
-
Journal article (peer-reviewed)abstract
- This paper reports on the fabrication and characterization of a thermopile detector with an integrated mid-infrared absorber structure. The fabricated absorber structure has shown an absorption of more than 95% in the wavelength range of 3.2 – 5.47 μm. The detector was fabricated with standard cleanroom process techniques and equipment. The serial resistance was measured at about 315 kΩ at room temperature. The photosensitivity of the detector was characterized for a signle wavelength (4.26 µm) and a band of wavelength ranging from 2.5 –5.5 µm through two different measurement setups. In the first measurement setup, the photosensitivity was estimated at 57.5 V·mm2·W-1 through a MEMS-based infrared radiation source and with an optical band-pass filter of wavelength 4.26µm. The following characterization was performed to characterise the photosensitivity of the detector in a broader wavelength range. This measurement was taken using a monochromator setup utilizing a reference photodetector for calculations of the optical power of the infrared source. The photosensitivity and the specific detectivity (D*) of the fabricated detector were measured to values of 30-92 V·W-1 and 8.0×107-2.4×108 cm·Hz1/2·W-1, respectively, in the wavelength range of 2.8 – 5 µm. The time constant was estimated to around 21 ms
|
|
| 8. |
- Ashraf, Shakeel, 1984-, et al.
(author)
-
Thermoelectric Properties of n-Type Molybdenum Disulfide (MoS2) Thin Film by Using a Simple Measurement Method
- 2019
-
In: Materials. - : MDPI. - 1996-1944. ; 12:21
-
Journal article (peer-reviewed)abstract
- In this paper, a micrometre thin film of molybdenum disulfide (MoS2) is characterized for thermoelectric properties. The sample was prepared through mechanical exfoliation of a molybdenite crystal. The Seebeck coefficient measurement was performed by generating a temperature gradient across the sample and recording the induced electrical voltage, and for this purpose a simple measurement setup was developed. In the measurement, platinum was utilized as reference material in the electrodes. The Seebeck value of MoS2 was estimated to be approximately -600 mu V/K at a temperature difference of 40 degrees C. The negative sign indicates that the polarity of the material is n-type. For measurement of the thermal conductivity, the sample was sandwiched between the heat source and the heat sink, and a steady-state power of 1.42 W was provided while monitoring the temperature difference across the sample. Based on Fourier's law of conduction, the thermal conductivity of the sample was estimated to be approximately 0.26 Wm(-1) K-. The electrical resistivity was estimated to be 29 Omega cm. The figure of merit of MoS2 was estimated to be 1.99 x 10(-4).
|
|
| 9. |
- Gaynullin, Bakhram, 1967-, et al.
(author)
-
Advanced Pressure Compensation in High Accuracy NDIR Sensors for Environmental Studies
- 2023
-
In: Sensors. - : MDPI AG. - 1424-8220. ; 23:5
-
Journal article (peer-reviewed)abstract
- Measurements of atmospheric gas concentrations using of NDIR gas sensors requires compensation of ambient pressure variations to achieve reliable result. The extensively used general correction method is based on collecting data for varying pressures for a single reference concentration. This one-dimensional compensation approach is valid for measurements carried out in gas concentrations close to reference concentration but will introduce significant errors for concentrations further away from the calibration point. For applications, requiring high accuracy, collecting, and storing calibration data at several reference concentrations can reduce the error. However, this method will cause higher demands on memory capacity and computational power, which is problematic for cost sensitive applications. We present here an advanced, but practical, algorithm for compensation of environmental pressure variations for relatively low-cost/high resolution NDIR systems. The algorithm consists of a two-dimensional compensation procedure, which widens the valid pressure and concentrations range but with a minimal need to store calibration data, compared to the general one-dimensional compensation method based on a single reference concentration. The implementation of the presented two-dimensional algorithm was verified at two independent concentrations. The results show a reduction in the compensation error from 5.1% and 7.3%, for the one-dimensional method, to −0.02% and 0.83% for the two-dimensional algorithm. In addition, the presented two-dimensional algorithm only requires calibration in four reference gases and the storing of four sets of polynomial coefficients used for calculations.
|
|
| 10. |
|
|
| 11. |
|
|
| 12. |
- Gaynullin, Bakhram, 1967-, et al.
(author)
-
Environmental monitoring of methane utilizing multispectral NDIR gas sensing for compensation of spectral impact from water vapor in air
- 2022
-
In: Proceedings of IEEE Sensors. - : IEEE. - 9781665484640
-
Conference paper (peer-reviewed)abstract
- A multispectral nondispersive infrared (NDIR) sensor was developed for simultaneous detection of methane and water vapor in air. The NDIR sensor is capable of measuring optic transmission in the CH4 absorption spectra at 3.375 μm and the H2O absorption spectra at 2.7 μm. Data from a third channel, 3.95 μm, is used as reference value for 'zero-level' calibration. The actual CH4 concentration is retrieved by adjusting the data obtained in the CH4 spectra with respect to the concentration sensed in the H2O spectra. A calibration procedure was developed and tested, which involves matching of the absorbed light energy in the CH4 and the H2O spectrum in humid reference environments. A compensation algorithm for elimination of humidity impact was developed and validated in environments with variable CH4 and H2O concentrations. By implementing the multispectral approach, and the developed algorithm, an uncertainty of 15-25 ppm relative the reference concentrations was achieved. For a concentration range valid for environmental monitoring applications this should be compared to an uncertainty of 180-200 ppm for the non-corrected CH4 concentration.
|
|
| 13. |
- Gaynullin, Bakhram, 1967-
(author)
-
High accuracy low-cost NDIR sensing
- 2019
-
Licentiate thesis (other academic/artistic)abstract
- Sensing gas concentrations using optical absorption offers valuable advantages over other methods ina wide variety of real-world applications from industrial processes to environmental change. One of the most rapidly developing detection techniques on the global market is the non-dispersive infrared method (NDIR). Sensors developed based on this technique satisfy a growing demand for low-cost, reliable and long-term maintenance-free solutions. The technologies available to support this field for sensor key components such as light sources, photo detectors, optic cavities, and electronic components, have advanced rapidly in recent years. This development has led to an increasing number of application fields, due to significant improvements in accuracy, sensitivity and resolution.However, this technique has limitations related to basic physical principles and sensor design performance. Variation in sensing environments’ temperature and pressure, the impact of water vapour presence and sensor component ageing are the most important interfering factors for investigation. Errors in measured values could be caused by any of these factors because they influence various sensor parts and the environment’s physical properties. The correct interpretation of error sources is one the most difficult and important tasks involved in designing stable, high-precision sensors.To facilitate investigations into measurement performance limitations, test equipment was developed along with test approaches capable of creating experimental conditions that exceed the tested sensor’ stolerances. The studied resolution limit for long-path sensors is about 100 ppb. For measurements in fresh air concentrations (approximately 400 ppm of CO2), this is equivalent to a precision of less than0.1%. The methods used to reduce possible inaccuracies due to various error sources’ impacts should possess compensatory capabilities and precisions that exceed this value.To improve the pressure compensation procedure’s performance, a complete advanced system that includes everything from a lab test bench to the supporting software and comprehensive calculation algorithm was developed. The test bench creates pressure conditions that deviate from the reference value by less than 0.2 mbar (or 0.02% of the standard pressure, 1013 mbar).One of this study’s major findings is the concentration range-independent pressure compensation method. The advanced conditions achieved with the test station also facilitated the discovery and characterisation of the sources of long-term drift in methane concentration measurement.
|
|
| 14. |
- Gaynullin, Bakhram, 1967-, et al.
(author)
-
Implementation of NDIR technology for selective sensing of gases with common absorption spectra
- 2023
-
In: 2023 IEEE International Instrumentation and Measurement Technology Conference (I2MTC). - : IEEE. - 9781665453837
-
Conference paper (peer-reviewed)abstract
- A selective algorithm for nondispersive infrared (NDIR) sensing of gases with overlapping absorption spectra was developed and evaluated in modified multichannel NDIR sensor. Measurements in the optic channel with the spectral band where two gas species (target and secondary gas) have overlapping absorption lines are complemented by additional measurements in second channel where spectral absorption for only one gas (secondary gas) is present. The real concentration for the target gas is retrieved by adjusting the absorption data obtained in the overlapping gas spectra's optic channel, with respect to the absorption data retrieved in the second optic channel that has sensitivity only for the secondary gas. An implementation example is performed by obtaining the true concentration of CH4 (as target gas) in a mixture with H2O vapor. The channel for the target gas is equipped by an optic filter with spectra at 3.375 μm where both CH4 and H2O have absorption lines. The complementary second channel provides sensing in spectra at 2.7 μm where only H2O have absorption. Data from a third channel, at 3.95 μm, is used as reference value for 'zero-level' calibration. A calibration procedure was developed and tested, which involves matching of the absorbed light energy in target and secondary channels in humid reference environments. A selective algorithm for sensing of CH4 with elimination of spectral impact from H2O was validated in environments with variable CH4 and H2O concentrations. By implementing the multispectral approach and the developed algorithm, an uncertainties of 5-10 ppm relative the reference concentrations were achieved. For the environments where selective algorithm was validated this should be compared to an uncertainty of 70-90 ppm for the non-corrected CH4 concentration.
|
|
| 15. |
|
|
| 16. |
- Hussain, Mazhar, 1980-, et al.
(author)
-
A Deep Learning Approach for Classification and Measurement of Hazardous Gases Using Multi-Sensor Data Fusion
- 2023
-
In: 2023 IEEE Sensors Applications Symposium (SAS). - : IEEE conference proceedings.
-
Conference paper (peer-reviewed)abstract
- Significant risks to public health and the environment are posed by the release of hazardous gases from industries such as pulp and paper. In this study, the aim was to develop a multi-sensor system with a minimal number of sensors to detect and identify hazardous gases. Training and test data for two gases, hydrogen sulfide and methyl mercaptan, which are known to contribute significantly to odors, were generated in a controlled laboratory environment. The performance of two deep learning models, a 1d-CNN and a stacked LSTM, for data fusion with different sensor configurations was evaluated. The performance of these models was compared with a baseline machine learning model. It was observed that the baseline model was outperformed by the deep learning models and achieved good accuracy with a four-sensor configuration. The potential of a cost-effective multi-sensor system and deep learning models in detecting and identifying hazardous gases is demonstrated by this study, which can be used to collect data from multiple locations and help guide the development of in-situ measurement systems for real-time detection and identification of hazardous gases at industrial sites. The proposed system has important implications for reducing pollution and protecting public health.
|
|
| 17. |
- Klang, Nina, 1978-, et al.
(author)
-
Intervention combining cooperative learning and instruction in reading comprehension strategies in heterogeneous classrooms
- 2022
-
In: Nordic Journal of Literacy Research. - : Nordic Open Access Scholarly Publishing (NOASP). - 2464-1596. ; 8:1, s. 44-64
-
Journal article (peer-reviewed)abstract
- The aim of this study was to investigate the effects of intervention, combining instruction in cooperative learning and reading comprehension strategies on students’ reading comprehension in grade 5. The teachers in the experiment group implemented the intervention while the teachers in the control group received training in reading comprehension strategies and taught as usual. Students in the experiment group and control group participated in tests of reading comprehension before and after the intervention. The results showed that being a part of the experiment group did not lead to greater gains in reading comprehension above the control group. Students of teachers who did not fully implement the intervention attained higher scores on reading comprehension than students in the control group. Students of teachers who fully implemented the intervention, on the other hand, received lower scores. The results are discussed with regard to research on teachers’ integration of intervention into their instructional routines.
|
|
| 18. |
- Mattsson, Claes, 1978-
(author)
-
Design, Fabrication and Optimization of Thermal Radiation Detectors Based on Thin Polymer Membranes
- 2009
-
Doctoral thesis (other academic/artistic)abstract
- The number of applications in which infrared radiation sensors are used is increasing. In some applications, the cost of the sensor itself is an issue, and simple solutions are thus required. In this thesis, the investigations have related to the use of thin polymer membranes in thermal infrared sensors, such as bolometers and thermopiles. Infrared sensors are usually subcategorized into photonic sensors and thermal sensors. For detection of infrared radiation using a photodetector, there is a requirement for low band-gap material. The need of cooling makes infrared photodetectors rather expensive, and not an alternative for low-cost applications. In thermal sensors, the heat generated from the incident infrared radiation is converted into an electrical output by means of a heat sensitive element. Thermal sensors operate at room temperature, which makes them a low-cost alternative. The basic structure of thermal sensors consists of a temperature sensitive element connected to a heat sink through a structure with low thermal conductance. It is common to use thin membranes of Silicon or Silicon Nitride as thermal insulation between the heat sink and the sensitive element. In comparison, polymers have a thermal conductance that is lower than in these materials, and this increases the generated temperature in the sensitive element. A polymer such as SU-8 has a low thermal conductivity and is applied using a spin coater. This reduces the number of complex processing steps. This thesis presents a new application of SU-8 as a closed membrane in a thermal sensor. The concept was initially demonstrated by fabricating a nickel bolometer and titanium/nickel thermopile structure with a 5 µm SU-8 / SiO2 membrane. However, for the sensor responsivity to be able to compete with commercial thermal sensors the structures, some optimization was required. Since the thermopile generates its own voltage output and requires no external bias, the optimizations were focused on this structure. There exist a number available software tools for thermal simulation of components. However, to the author’s best knowledge, there exist no tool for design optimization of thermopiles with closed membranes. An optimization tool using iterative thermal simulations was developed and evaluated. A new thermopile structure, based on the optimization results, was both fabricated and characterized. Using an infrared laser with a small spot, the measured responsivity of the manufactured thermopile was higher than that of a commercial sensor. In the case of a defocused spot and for longer wavelengths, the infrared absorption in the absorption layer reduces and degrades the responsivity. The thermopile was further evaluated as a sensor in a carbon dioxide meter application based on the NDIR principle. An increase in the CO2 concentration demonstrated a clear decrease in the thermopile voltage response, as was expected. By normalizing the voltage response and comparing it with a commercial sensor, this showed that the SU-8 based thermopile is relatively more sensitive to changes in the CO2 concentration.
|
|
| 19. |
- Mattsson, Claes, 1978-, et al.
(author)
-
Design of a Micromachined Thermopile Infrared Sensor with a Self-Supported SiO2/SU-8 Membrane
- 2008
-
In: IEEE Sensors Journal. - Piscataway, USA : IEEE. - 1530-437X .- 1558-1748. ; 8:12, s. 2044-2052
-
Journal article (peer-reviewed)abstract
- In the infrared region of the spectrum thermoelectric detectors such as the thermopile, are extensively used. These detectors rely on the well-known Seebeck effect, in which there is a direct conversion of thermoelectric differentials into electrical voltage. The temperature difference over thermocouple junctions is in general, created by forming a thin membrane connected to the silicon bulk. In many existing thermopiles, materials such as Si and Si3N4 have been used as membrane. These materials suffer from relatively high thermal conductivity, which lowers the membrane temperature and reduces the sensitivity of the detector. A material such as SU-8 2002 has a much lower thermal conductivity and is applied using standard photolithographic processing steps. This work presents thermal simulations regarding the use of SU-8 2002 as a thermal insulating membrane as compared to Si and Si3N4. The simulation results presented show that the temperature increase in a 5 µm SiO2/SU-8 membrane is about 9% higher than in a 1 µm Si3N4 membrane, despite the membrane thickness being increased by a factor of 5. A thermopile consisting of 196 serially interconnected Ti/Ni thermocouples positioned on a 5 µm SiO2/SU-8 2002 membrane has been fabricated. The sensitivity of the fabricated device has been evaluated in the infrared region, using a 1.56 µm IR laser and a xenon arc lamp together with a monochromator. The measurement results show a sensitivity of approximately 5 V/W over the wavelength range between 900 - 2200 nm. Measurements performed in a vacuum chamber show that the sensitivity of the detector could be increased by more than a factor of 3 by mounting the detector in a vacuum sealed capsule.
|
|
| 20. |
- Mattsson, Claes, 1978-, et al.
(author)
-
Experimental evaluation of a thermopile detector with SU-8 membrane, in a carbon dioxide meter setup
- 2009
-
In: IEEE Sensors Journal. - 1530-437X .- 1558-1748. ; 9:12, s. 1633-1638
-
Journal article (peer-reviewed)abstract
- Continuous control of the carbon dioxide levels in the ventilation systems in office buildings and public schools has been shown to increase productivity and save money. However, these measurement systems require further developments in order to be more cost effective. This paper presents an evaluation of an Al/Bi thermopile detector with a 4 µm thin SiO2/SU-8 membrane in a CO2 meter application using the NDIR (Non-Dispersive Infrared Technology). The system consists of an 11 cm aluminum tube, used as the sample chamber and in which a light source and a thermopile detector with a 4.26 µm optical bandpass filter are positioned on its opposite sides. The light source is pulsed with a frequency of 0.5 Hz. The voltage response of the Al/Bi thermopile is measured for different CO2 concentrations, and, as expected according to the Lambert-Beer law, there is an exponential decrease in the measured intensity. The absolute response is about 50 % lower than for a commercial HMS J21 thermopile from Heimann Sensor GmbH. In relative terms, on the other hand, the Al/Bi thermopile is more sensitive for changes in the CO2 concentration. At 7500 ppm, the voltage response has decreased to 40 % of the reference response measured in the nitrogen atmosphere.
|
|
| 21. |
- Mattsson, Claes, 1978-, et al.
(author)
-
Fabrication and characterization of a design optimized SU-8 thermopile with enhanced sensitivity
- 2009
-
In: Measurement science and technology. - : IOP. - 0957-0233 .- 1361-6501. ; 20:11, s. 115202-
-
Journal article (peer-reviewed)abstract
- In the infrared wavelength region, thermopiles are an important type of detectors. A major advantage of thermopiles is their non-cooling requirement. Depending on the applied absorption layer, their responsivity is often rather flat within a large wavelength region. This work presents the fabrication and characterization of a sensitivity and design optimized thermopile detector with a 4 µm self-supported SiO2/SU-8 membrane. The structure consists of 240 series interconnected thermocouple junctions obtained by a metal evaporation and lift-off. Two metal combinations have been evaluated, namely, nickel/titanium and aluminium/bismuth. Series resistances of 76 k and 283 k were measured for the Ni/Ti thermopile and the Al/Bi thermopile respectively. For the Al/Bi thermopile a responsivity of 60 V/W was achieved using a 1.56 µm fibre coupled diode laser with a power of 3.5 mW. Using a white light source with a radiation flux of 0.45 W/mm2 a voltage response of 68 V mm2/W was measured for the Al/Bi thermopile. The time constant of the characterized detectors was calculated as being 70 ms, using the pulsed IR laser.
|
|
| 22. |
- Mattsson, Claes, 1978-
(author)
-
Fabrication and Characterization of Photon Radiation Detectors
- 2007
-
Licentiate thesis (other academic/artistic)abstract
- This thesis involves a study the fabrication and characterization of photon radiation detectors. The focus has been to develop and improve the performance of optical measurement systems, but also to reduce their cost. The work is based on the study of two types of detectors, the position sensitive detector and the thermal detector. Infrared detectors are usually subcategorized into photonic detectors and thermal detectors. In the thermal detectors, heat generated from the incident infrared radiation is converted into an electrical output by some sensitive element. The basic structure of these detectors consists of a temperature sensitive element connected to a heat sink through a thermally isolating structure. Thin membranes of Silicon and Silicon nitride have been commonly used as thermally insulation between the heat sink and the sensitive elements. However, these materials suffer from relatively high thermal conductivity, which lowers the response of the detector. The fabrication of these membranes also requires rather advanced processing techniques and equipment. SU-8 is an epoxy based photoresist, which has low thermal conductivity and requires only standard photolithography. A new application of SU-8 as a self-supported membrane in a thermal detector is presented. This application is demonstrated by the fabrication and characterization of both an infrared sensitive thermopile and a bolometer detector. The bolometer consists of nickel resistances connected in a Wheatstone bridge configuration, whereas the thermopile uses serially interconnected Ti/Ni thermocouple junctions. The position sensitive detectors include the lateral effect photodiodes and the quadrant detectors. Typical applications for these detectors are distance measurements and as centering devices. In the quadrant detectors, the active region consists of four pn-junctions separated by a narrow gap. The size of the active region in these detectors depends on the size of the light spot. In outdoor application, this spot size dependence degrades the performance of the four-quadrant detectors. In this thesis, a modified four-quadrant detector having the pn-junctions separated by a larger distance has been fabricated and characterized. By separating the pn-junctions the horizontal electric filed in the active region is removed, making the detector spot size insensitive. Linearity of the lateral effect photodiodes depends on the uniformity of the resistive layer in the active region. The introduction of mechanical stress in an LPSD results in a resistance change mainly due to resistivity changes, and this affects the linearity of the detector. Measurements and simulations, where mechanical stress is applied to LPSDs are presented, and support this conclusion.
|
|
| 23. |
- Mattsson, Claes, 1978-, et al.
(author)
-
Thermal simulation and design optimization of a thermopile infrared detector with SU-8 membrane
- 2009
-
In: Journal of Micromechanics and Microengineering. - : IOP Publishing. - 0960-1317 .- 1361-6439. ; 19:5, s. 055016-
-
Journal article (peer-reviewed)abstract
- Simulation and optimization tools are commonly used in the design phase of advanced electronics devices. In this work, we present a thermal simulation and design optimization tool for infrared thermopile detectors based on a closed membrane structure. The tool can be used to simulate and optimize thermopile detectors with an arbitrary number of design parameters. The optimization utilizes the Nelder–Mead and the adaptive simulated annealing optimization algorithms to maximize the system performance. A thermopile detector with an SU-8-based closed membrane and metal–metal thermocouples has been simulated and optimized. Based on the results generated by the tool, an optimized detector has been fabricated and characterized. The results from the measurements presented are in good agreement with the simulation results.
|
|
| 24. |
- Wernstedt, Ingrid, 1978, et al.
(author)
-
A common polymorphism in the interleukin-6 gene promoter is associated with overweight
- 2004
-
In: Int J Obes Relat Metab Disord. ; 28:10, s. 1272-9
-
Journal article (peer-reviewed)abstract
- OBJECTIVE: Human body fat mass is to a large extent genetically determined, but little is known about the susceptibility genes for common obesity. Interleukin-6 (IL-6) suppresses body fat mass in rodents, and IL-6 treatment increases energy expenditure in both rodents and humans. The -174 G/C single-nucleotide polymorphism (SNP) in the IL-6 gene promoter is common in many populations, and -174 C-containing promoters have been found to be weaker enhancers of transcription. Moreover, a SNP at position -572 in the IL-6 promoter has recently been reported to affect transcription. The objective was to investigate the association between the IL-6 gene promoter SNPs and obesity. DESIGN: Trans-sectional association study of IL-6 gene promoter SNPs and indices of obesity. SUBJECTS: Two study populations, the larger one consisting of hypertensive individuals (mean age 57 y, 73% males, n=485) and the other consisting of 20 y younger nonobese healthy females (n=74). MEASUREMENTS: Genotyping for the -174 IL-6 G/C and the -572 G/C SNPs, body mass index (BMI), serum leptin levels, serum IL-6 levels, C-reactive protein, fasting blood glucose and various blood lipids. RESULTS: The common -174 C allele (f(C)=0.46), but not any -572 allele, was associated with higher BMI and higher serum leptin levels in both study populations. In the larger population, there were significant odds ratios for the association of CC (2.13) and GC (1.76) genotypes with overweight (BMI>25 kg/m(2)). Moreover, as the C allele was common, it accounted for a significant population-attributable risk of overweight (12%; CI 2-21%), although its average effect was modest in this sample. CONCLUSION: Genetically determined individual differences in production of IL-6 may be relevant for the regulation of body fat mass.
|
|
