onr:"swepub:oai:research.chalmers.se:c80322b5-10ea-4cf7-92f8-6936c2c5574d"
Search: onr:"swepub:oai:research.chalmers.se:c80322b5-10ea-4cf7-92f8-6936c2c5574d" > Surface modificatio...
- 1 of 1
- Previous record
- Next record
- To hitlist
Surface modification of PM gearlever
-
- Johansson, S. C. (author)
- RISE,KIMAB
-
- Frisk, K. (author)
- RISE,KIMAB
-
- Gustafson, Å (author)
- Scania CV AB
- show more...
- Malmberg, L. (author)
- show less...
- (creator_code:org_t)
- ISBN 9781899072194
- European Powder Metallurgy Association (EPMA), 2010
- 2010
- English.
- In: World Powder Metallurgy Congress and Exhibition, World PM 2010; Florence; Italy; 10 October 2010 through 14 October 2010. - : European Powder Metallurgy Association (EPMA). - 9781899072194 ; 3
- Conference paper (peer-reviewed)
Abstract
Subject headings
Close
- A novel manufacturing concept for a gearlever has been evaluated by manufacturing of test components of two materials. Iron-based powders were used, and pressing and sintering was followed by a few different variants of hardening and surface densification. The components have been evaluated by means of component function testing, component fatigue testing, microstructure characterization, hardness measurements and residual stress determination. The gearlever is found to perform well in the function testing and shows also good fatigue properties that well match the demands for the intended application. The porosity in the sintered material is inhomogeneous, and some compaction-induced defects were observed in the material, which thus seems not to give any significant negative impact on the sintered product performance. The results show a doubling in hardness after hardening. If the materials were shot-peened (or shot-blasted) after hardening the surface hardness increased down to a depth of approximately 0.2 mm compared to the hardened material. The case-hardening should be applied after shot-peening to obtain significant effect on surface hardness within the outermost 0.1 mm. In principle no surface densification was created if shoot-peening was performed after hardening.
Subject headings
- TEKNIK OCH TEKNOLOGIER -- Materialteknik -- Metallurgi och metalliska material (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering -- Metallurgy and Metallic Materials (hsv//eng)
- TEKNIK OCH TEKNOLOGIER -- Materialteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering (hsv//eng)
Publication and Content Type
- kon (subject category)
- ref (subject category)
Find in a library
- World Powder Metallurgy Congress and Exhibition, World PM 2010; Florence; Italy;... (Search for host publication in LIBRIS)
To the university's database
- 1 of 1
- Previous record
- Next record
- To hitlist
Find more in SwePub
- By the author/editor
- Johansson, S. C.
- Frisk, K.
- Gustafson, Å
- Malmberg, L.
- Bengtsson, S.
- Nyborg, Lars, 19 ...
- About the subject
-
- ENGINEERING AND TECHNOLOGY
- ENGINEERING AND ...
- and Materials Engine ...
- and Metallurgy and M ...
-
- ENGINEERING AND TECHNOLOGY
- ENGINEERING AND ...
- and Materials Engine ...
- Articles in the publication
- World Powder Met ...
- By the university
- Chalmers University of Technology
- RISE
Search outside SwePub
- Extend your search to:
- Google Book Search
- Google Scholar
Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.
- Copyright © LIBRIS - National Library Systems
- LIBRIS.kb.se
