| 1. |
- Gärdenfors, Peter, et al.
(författare)
-
Varför skall vi minnas våra beslut?
- 1993
-
Ingår i: Huvudinnehåll : 12 filosofiska uppsatser. - 9188248305 ; , s. 189-205
-
Bokkapitel (refereegranskat)
|
|
| 2. |
|
|
| 3. |
|
|
| 4. |
- Moberg, Christina, et al.
(författare)
-
De unga gör helt rätt när de stämmer staten
- 2022
-
Ingår i: Aftonbladet. - 1103-9000.
-
Tidskriftsartikel (populärvet., debatt m.m.)abstract
- 1 620 forskare och lärare i forskarvärlden: Vi ställer oss bakom Auroras klimatkrav
|
|
| 5. |
- Agertz, Oscar, et al.
(författare)
-
Vintergatan - i. The origins of chemically, kinematically, and structurally distinct discs in a simulated milky way-mass galaxy
- 2021
-
Ingår i: Monthly Notices of the Royal Astronomical Society. - : Oxford University Press (OUP). - 0035-8711 .- 1365-2966. ; 503:4, s. 5826-5845
-
Tidskriftsartikel (refereegranskat)abstract
- Spectroscopic surveys of the Milky Way's stars have revealed spatial, chemical, and kinematical structures that encode its history. In this work, we study their origins using a cosmological zoom simulation, VINTERGATAN, of a MilkyWay-mass disc galaxy. We find that in connection to the last major merger at z ∼ 1.5, cosmological accretion leads to the rapid formation of an outer, metal-poor, low-[α/Fe] gas disc around the inner, metal-rich galaxy containing the old high-[α/Fe] stars. This event leads to a bimodality in [α/Fe] over a range of [Fe/H]. A detailed analysis of how the galaxy evolves since z ∼ 1 is presented. We demonstrate the way in which inside-out growth shapes the radial surface density and metallicity profile and how radial migration preferentially relocates stars from the inner disc to the outer disc. Secular disc heating is found to give rise to increasing velocity dispersions and scale heights with stellar age, which together with disc flaring explains several trends observed in the MilkyWay, including shallower radial [Fe/H] profiles above the mid-plane.We show how the galaxy formation scenario imprints non-trivial mappings between structural associations (i.e. thick and thin discs), velocity dispersions, α-enhancements, and ages of stars; e.g. the most metal-poor stars in the low-[α/Fe] sequence are found to have a scale height comparable to old high-[α/Fe] stars. Finally, we illustrate how at low spatial resolution, comparable to the thickness of the galaxy, the proposed pathway to distinct sequences in [α/Fe]-[Fe/H] cannot be captured.
|
|
| 6. |
|
|
| 7. |
- Andersson, Nils-Eric, et al.
(författare)
-
Face milling of AA7010 at high cutting speeds
-
Annan publikation (övrigt vetenskapligt/konstnärligt)abstract
- Face milling using different commercial tools and inserts at varying cutting speeds on a high strength aluminium alloy has been performed. The surface integrity of the machined samples has been investigated in terms of surface roughness, residual stresses, hardness and peak broadening from x-ray diffraction at grazing angle incidence. Some fatigue testing of the machined surfaces has been done. The cutting chips from the different machining parameters are investigated and compared to one another. The results show a strong influence of tool insert on surface roughness, residual stress, peak broadening, and hardness profile and fatigue properties. The influence of cutting speed on the surface integrity is much smaller. The cutting speed does however influence the size and shape of the cutting chips. There is also a general decrease in peak broadening from x-ray diffraction very near the machined surface after high cutting speeds. This could be explained by a higher local heating of the work piece at very high cutting speeds.
|
|
| 8. |
- Andersson, Nils-Eric, et al.
(författare)
-
Fatigue crack growth rate in commercial thick plates of AA7010
-
Annan publikation (övrigt vetenskapligt/konstnärligt)abstract
- A mapping of fatigue crack growth rates in commercial thick plates of a high strength aluminium alloy, AA7010-T7451/52, has been done. The investigated plate thicknesses were 100, 150 and 200 mm. Material from near edge and mid-width at near surface and mid-thickness has been investigated. Measurements of crack length have been perfonned using DC potential drop. Cyclic condensation is used in order to be able to investigate local crack growth after fracture. Influence of crack closure, crack branching and slow growing side cracks on fatigue crack growth rate of S-L and L-T oriented CT specimens are discussed. S-L specimens show the highest fatigue crack growth rates. Beach marks on the fracture surface due to the cyclic condensation reveals locally straight crack fronts. A difference in growth rate between near surface and mid-thickness positioned L-T specimens are found. At a nominal ΔK of - 7 MPa√m the mid-thickness samples showed a sudden crack growth rate acceleration. The result of the investigation is explained in tenns of variations in structure, which is a function of position in the plates and plate thickness.
|
|
| 9. |
- Andersson, Nils-Eric, et al.
(författare)
-
Fatigue crack growth rate in thick plates of 7010
- 1999
-
Ingår i: Fatigue '99. - Beijing : Higher Education Press. - 9787040075823 ; , s. 445-450
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- A mapping of fatigue crack growth rates in thick plates of a high strength aluminium alloy has been done. The plate thicknesses investigated was 100, 150 and 200 mm. In this work, material from near edge at near surface and mid-thickness has been investigated. Measurements of crack length has been performed using DC potential drop. Cyclic condensation is used in order to reveal crack growth behaviour for stage I and the earlier part of stage II crack growth. Influence of crack closure, crack branching and slow growing side cracks on fatigue crack growth rate of S-L and L-T oriented specimens are discussed. Variation of difference in growth rate in the upper part of the stage II growth between near surface and mid thickness positioned L-T specimens are found to vary with plate thickness.
|
|
| 10. |
|
|
