| 1. |
- Kanai, M, et al.
(author)
-
- 2023
-
swepub:Mat__t
|
|
| 2. |
- Niemi, MEK, et al.
(author)
-
- 2021
-
swepub:Mat__t
|
|
| 3. |
- Abdesselam, A., et al.
(author)
-
The ATLAS semiconductor tracker end-cap module
- 2007
-
In: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 575:3, s. 353-389
-
Journal article (peer-reviewed)abstract
- The challenges for the tracking detector systems at the LHC are unprecedented in terms of the number of channels, the required read-out speed and the expected radiation levels. The ATLAS Semiconductor Tracker. (SCT) end-caps have a total of about 3 million electronics channels each reading out every 25 ns into its own on-chip 3.3 mu s buffer. The highest anticipated dose after 10 years operation is 1.4x10(14) cm(-2) in units of 1 MeV neutron equivalent (assuming the damage factors scale with the non-ionising energy loss). The forward tracker has 1976 double-sided modules, mostly of area similar to 70 cm(2), each having 2 x 768 strips read out by six ASICs per side. The requirement to achieve an average perpendicular radiation length of 1.5% X-0, while coping with up to 7 W dissipation per module (after irradiation), leads to stringent constraints on the thermal design. The additional requirement of 1500e(-) equivalent noise charge (ENC) rising to only 1800e(-) ENC after irradiation, provides stringent design constraints on both the high-density Cu/Polyimide flex read-out circuit and the ABCD3TA read-out ASICs. Finally, the accuracy of module assembly must not compromise the 16 mu m (r phi) resolution perpendicular to the strip directions or 580 mu m radial resolution coming from the 40 mrad front-back stereo angle. A total of 2210 modules were built to the tight tolerances and specifications required for the SCT. This was 234 more than the 1976 required and represents a yield of 93%. The component flow was at times tight, but the module production rate of 40-50 per week was maintained despite this. The distributed production was not found to be a major logistical problem and it allowed additional flexibility to take advantage of where the effort was available, including any spare capacity, for building the end-cap modules. The collaboration that produced the ATLAS SCT end-cap modules kept in close contact at all times so that the effects of shortages or stoppages at different sites could be rapidly resolved.
|
|
| 4. |
- Booker, Ian Don, et al.
(author)
-
Oxidation induced ON1, ON2a/b defects in 4H-SiC characterized by DLTS
- 2014
-
In: SILICON CARBIDE AND RELATED MATERIALS 2013, PTS 1 AND 2. - : Trans Tech Publications. ; , s. 281-284
-
Conference paper (peer-reviewed)abstract
- The deep levels ON1 and ON2a/b introduced by oxidation into 4H-SiC are characterized via standard DLTS and via filling pulse dependent DLTS measurements. Separation of the closely spaced ON2a/b defect is achieved by using a higher resolution correlation function (Gaver-Stehfest 4) and apparent energy level, apparent electron capture cross section and filling pulse measurement derived capture cross sections are given.
|
|
| 5. |
|
|
| 6. |
- Diez, S., et al.
(author)
-
A double-sided, shield-less stave prototype for the ATLAS Upgrade strip tracker for the High Luminosity LHC
- 2014
-
In: Journal of Instrumentation. - 1748-0221. ; 9, s. P03012-
-
Journal article (peer-reviewed)abstract
- A detailed description of the integration structures for the barrel region of the silicon strips tracker of the ATLAS Phase-II upgrade for the upgrade of the Large Hadron Collider, the so-called High Luminosity LHC (HL-LHC), is presented. This paper focuses on one of the latest demonstrator prototypes recently assembled, with numerous unique features. It consists of a shortened, shield-less, and double sided stave, with two candidate power distributions implemented. Thermal and electrical performances of the prototype are presented, as well as a description of the assembly procedures and tools.
|
|
| 7. |
- Gonzalez-Sevilla, S., et al.
(author)
-
A double-sided silicon micro-strip Super-Module for the ATLAS Inner Detector upgrade in the High-Luminosity LHC
- 2014
-
In: Journal of Instrumentation. - 1748-0221. ; 9, s. P02003-
-
Journal article (peer-reviewed)abstract
- The ATLAS experiment is a general purpose detector aiming to fully exploit the discovery potential of the Large Hadron Collider (LHC) at CERN. It is foreseen that after several years of successful data-taking, the LHC physics programme will be extended in the so-called High-Luminosity LHC, where the instantaneous luminosity will be increased up to 5 x 10(34) cm(-2) s(-1). For ATLAS, an upgrade scenario will imply the complete replacement of its internal tracker, as the existing detector will not provide the required performance due to the cumulated radiation damage and the increase in the detector occupancy. The current baseline layout for the new ATLAS tracker is an all-silicon-based detector, with pixel sensors in the inner layers and silicon micro-strip detectors at intermediate and outer radii. The super-module is an integration concept proposed for the strip region of the future ATLAS tracker, where double-sided stereo silicon micro-strip modules are assembled into a low-mass local support structure. An electrical super-module prototype for eight double-sided strip modules has been constructed. The aim is to exercise the multi-module readout chain and to investigate the noise performance of such a system. In this paper, the main components of the current super-module prototype are described and its electrical performance is presented in detail.
|
|
| 8. |
- Sun, Jianwu, et al.
(author)
-
Solar driven energy conversion applications based on 3C-SiC
- 2016
-
In: 16th International Conference on Silicon Carbide and Related Materials, ICSCRM 2015. - : Trans Tech Publications Ltd. - 9783035710427 ; , s. 1028-1031
-
Conference paper (peer-reviewed)abstract
- There is a strong and growing worldwide research on exploring renewable energy resources. Solar energy is the most abundant, inexhaustible and clean energy source, but there are profound material challenges to capture, convert and store solar energy. In this work, we explore 3C-SiC as an attractive material towards solar-driven energy conversion applications: (i) Boron doped 3C-SiC as candidate for an intermediate band photovoltaic material, and (ii) 3C-SiC as a photoelectrode for solar-driven water splitting. Absorption spectrum of boron doped 3C-SiC shows a deep energy level at ~0.7 eV above the valence band edge. This indicates that boron doped 3C-SiC may be a good candidate as an intermediate band photovoltaic material, and that bulk like 3C-SiC can have sufficient quality to be a promising electrode for photoelectrochemical water splitting.
|
|
| 9. |
|
|
