| 1. |
- Talabazar, Farzad Rokhsar, et al.
(författare)
-
Removal of per- and polyfluoroalkyl substances (PFAS) from wastewater using the hydrodynamic cavitation on a chip concept
- 2024
-
Ingår i: Chemical Engineering Journal. - : Elsevier BV. - 1385-8947 .- 1873-3212. ; 495
-
Tidskriftsartikel (refereegranskat)abstract
- The elimination of micropollutants such as highly fluorinated substances, including per- and polyfluoroalkyl substances (PFAS), in wastewater treatment plants has been receiving growing attention due to the urgent need to minimize their adverse effects on natural water and associated ecosystems. Conventional treatment methods often fall short in effectively removing PFAS. In this study, the Hydrodynamic Cavitation on a Chip concept (HCOC) was utilized to degrade 11 common PFAS variants (PFAS11) for the first time in three different hydrodynamic cavitation reactor set-ups, each enhanced with surface modifications involving roughness elements. Stockholm municipal wastewater treated by a Membrane BioReactor (MBR) process was subjected to fully developed cavitating flow treatment using the three distinct microscale hydrodynamic cavitation (HC) reactors. The obtained results indicate that the chemical-free HCOC technique employed in this study has a significant potential in the degradation of nearly all investigated PFAS11 compounds at a notable rate of 36.1 % while the combination with MBR process can prevent blockage within the fluidic channels, enabling continuous operation with high throughput processing rates. Our proposed methodology demonstrated promising results in eliminating PFAS and could contribute to advancements in the use of microscale HC to treat micropollutants in wastewater. These findings could be a major leap in water treatment technologies addressing the global burden of resource-efficient micropollutant water treatment.
|
|
| 2. |
- Abbasiasl, Taher, et al.
(författare)
-
A Flexible Cystoscope Based on Hydrodynamic Cavitation for Tumor Tissue Ablation
- 2022
-
Ingår i: IEEE Transactions on Biomedical Engineering. - : Institute of Electrical and Electronics Engineers (IEEE). - 0018-9294 .- 1558-2531. ; 69:1, s. 513-524
-
Tidskriftsartikel (refereegranskat)abstract
- Objective: Hydrodynamic cavitation is characterized by the formation of bubbles inside a flow due to local reduction of pressure below the saturation vapor pressure. The resulting growth and violent collapse of bubbles lead to a huge amount of released energy. This energy can be implemented in different fields such as heat transfer enhancement, wastewater treatment and chemical reactions. In this study, a cystoscope based on small scale hydrodynamic cavitation was designed and fabricated to exploit the destructive energy of cavitation bubbles for treatment of tumor tissues. The developed device is equipped with a control system, which regulates the movement of the cystoscope in different directions. According to our experiments, the fabricated cystoscope was able to locate the target and expose cavitating flow to the target continuously and accurately. The designed cavitation probe embedded into the cystoscope caused a significant damage to prostate cancer and bladder cancer tissues within less than 15 minutes. The results of our experiments showed that the cavitation probe could be easily coupled with endoscopic devices because of its small diameter. We successfully integrated a biomedical camera, a suction tube, tendon cables, and the cavitation probe into a 6.7 mm diameter cystoscope, which could be controlled smoothly and accurately via a control system. The developed device is considered as a mechanical ablation therapy, can be a solid alternative for minimally invasive tissue ablation methods such as radiofrequency (RF) and laser ablation, and could have lower side effects compared to ultrasound therapy and cryoablation.
|
|
| 3. |
- Abbasiasl, Taher, et al.
(författare)
-
Effect of intensified cavitation using poly (vinyl alcohol) microbubbles on spray atomization characteristics in microscale
- 2020
-
Ingår i: AIP Advances. - : American Institute of Physics (AIP). - 2158-3226. ; 10:2
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, cavitating flows inside a transparent cylindrical nozzle with an inner diameter of 0.9 mm were visualized, and the effect of cavitation on atomization characteristics of emerging sprays was investigated. Different patterns of cavitating flows inside the nozzle were visualized using a high-speed camera. In-house codes were developed to process the captured images to study the droplet size distribution and droplet velocity in different flow regimes. The results show that cavitating flows at the microscale have significant effects on atomization characteristics of the spray. Two working fluids, namely, water and poly(vinyl alcohol) microbubble (PVA MB) suspension, were employed. Accordingly, the injection pressures were detected as 690 kPa, 1035 kPa, and 1725 kPa for cavitation inception, supercavitation, and hydraulic flip flow regimes in the case of water, respectively. The corresponding pressures for the aforementioned patterns for PVA MB suspension were 590 kPa, 760 kPa, and 1070 kPa, respectively. At the microscale, as a result of a higher volume fraction of cavitation bubbles inside the nozzle, there is no large difference between the cavitation numbers corresponding to cavitating and hydraulic flip flows. Although the percentage of droplets with diameters smaller than 200 μm was roughly the same for both cases of water and PVA MB suspension, the Sauter mean diameter was considerably lower in the case of PVA MBs. Moreover, higher droplet velocities were achieved in the case of PVA MBs at lower injection pressures.
|
|
| 4. |
- Abdollahi, Morteza, et al.
(författare)
-
A process mineralogy approach to optimize molybdenite flotation in copper : molybdenum processing plants
- 2020
-
Ingår i: Minerals Engineering. - : Elsevier. - 0892-6875 .- 1872-9444. ; 157
-
Tidskriftsartikel (refereegranskat)abstract
- The Sungun copper-molybdenum operation in Iran uses a typical copper-molybdenum flowsheet to produce separate copper and molybdenum concentrates through flotation and regrinding of the rougher concentrates arising from the primary circuit. This site was used as a case study limited to the feed and products of the copper-molybdenum separation circuit, in which process mineralogy might improve the quality of the molybdenum concentrate thorough diagnostic analysis of key flowsheet streams. The undesirable presence of copper in the molybdenum concentrate was identified as a key focus for the investigation by process mineralogy, which has a history of successful process diagnosis. This is because it develops information on minerals, which is far more informative than chemical assays alone. Together with the assays, the mineralogical data inform the investigator of the type and quantity of minerals present, their state of liberation and textural associations, and metal recovery.A key finding was that the appearance of chalcopyrite in the molybdenum concentrate was due to the presence of a chalcopyrite-pyrite texture that avoided the chalcopyrite depression in the molybdenum circuit because of suitable pyrite flotation conditions. Recovery of liberated pyrite to this concentrate also diluted the molybdenum concentrate. The open-circuit format of the regrind circuit also contributed to the unnecessary production of ultrafine particles. This flaw expressed itself as ultrafine losses of molybdenite to the flotation tailings.
|
|
| 5. |
- Aghdam, Araz Sheibani, et al.
(författare)
-
A New Method for Intense Cavitation Bubble Generation on Layer-by-Layer Assembled SLIPS
- 2019
-
Ingår i: Scientific Reports. - : Nature Publishing Group. - 2045-2322. ; 9
-
Tidskriftsartikel (refereegranskat)abstract
- The importance of surface topology for the generation of cavitating flows in micro scale has been emphasized during the last decade. In this regard, the utilization of surface roughness elements is not only beneficial in promoting mass transportation mechanisms, but also in improving the surface characteristics by offering new interacting surface areas. Therefore, it is possible to increase the performance of microfluidic systems involving multiphase flows via modifying the surface. In this study, we aim to enhance generation and intensification of cavitating flows inside microfluidic devices by developing artificial roughness elements and trapping hydrophobic fluorinated lubricants. For this, we employed different microfluidic devices with various hydraulic diameters, while roughness structures with different lengths were formed on the side walls of microchannel configurations. The surface roughness of these devices was developed by assembling various sizes of silica nanoparticles using the layer-by-layer technique (D2). In addition, to compare the cavitating flow intensity with regular devices having plain surfaces (D1), highly fluorinated oil was trapped within the pores of the existing thin films in the configuration D2 via providing the Slippery Liquid-Infused Porous Surface (D3). The microfluidic devices housing the short microchannel and the extended channel were exposed to upstream pressures varying from 1 to 7.23 MPa. Cavitation inception and supercavitation condition occured at much lower upstream pressures for the configurations of D2 and D3. Interestingly, hydraulic flip, which rarely appears in the conventional conical nozzles at high pressures, was observed at moderate upstream pressures for the configuration D2 proving the air passage existence along one side of the channel wall.
|
|
| 6. |
- Bahrami, Ataallah, et al.
(författare)
-
A geometallurgical study of flotation performance in supergene and hypogene zones of Sungun copper deposit
- 2021
-
Ingår i: Mineral Processing and Extractive Metallurgy. - : Taylor & Francis. - 2572-6641 .- 2572-665X. ; 130:2, s. 126-135
-
Tidskriftsartikel (refereegranskat)abstract
- The feed of mineral processing plants, usually consist of different minerals from various geological zones, which show different behavior in separation processes. In this research, samples from supergene and hypogene zones were provided to investigate the flotation behavior of copper minerals. Flotation experiments were carried out in three phases of supergene sample, hypogene sample and mixed samples. Based on the results, the recovery rate of the mixed sample was 83.61%, which is 7.63% and 1.79% higher than the recovery of the samples of hypogene and supergene zones, respectively. The concentrate grade values obtained for blended, hypogene zone and supergene zone are 10.32%, 2.81% and 12.37%, respectively. The maximum values of flotation constant and infinite recovery are 0.956 (s−1) and 88.833% for the mixed sample. It was also concluded that the highest amount of k and infinitive recovery were related to supergene zone sulfide flotation which are 0.831 (s−1) and 84.33% respectively.
|
|
| 7. |
- Bahrami, Ataallah, et al.
(författare)
-
Combined Effect of Operating Parameters on Separation Efficiency and Kinetics of Copper Flotation
- 2019
-
Ingår i: Mining, metallurgy & exploration. - : Springer. - 2524-3462 .- 2524-3470. ; 36:2, s. 409-421
-
Tidskriftsartikel (refereegranskat)abstract
- This study aims to investigate the effects of operational variables on concentrate grade, recovery, separation efficiency, and kinetic parameters of the copper flotation process. For this purpose, the effects of the pulp solids content, collector and frother dosage, and preparation and concentrate collection time were studied using a Taguchi experimental design. The results of statistical analyses indicated that the concentrate collection time and pulp density were the most influential parameters on concentrate grade. Considering copper recovery, concentrate collection time, collector dosage, and pulp density were the most significant variables, in decreasing order of importance. Also, the separation efficiency was mostly influenced by the concentrate collection time. Furthermore, kinetic studies showed that the second-order rectangular distribution model perfectly matched the experimental flotation data. The highest kinetic constant of 0.0756 s−1 was obtained from the test, which was performed with 35% solids content and 40 and 20 g/t collector and frother, respectively. The highest predicted copper recovery of 99.57% was obtained from the test at 30% solids content, and the collector and frother dosages of 40 and 15 g/t, respectively.
|
|
| 8. |
- Bahrami, Ataallah, et al.
(författare)
-
Isolation and removal of cyanide from tailing dams in gold processing plant using natural bitumen
- 2020
-
Ingår i: Journal of Environmental Management. - : Elsevier. - 0301-4797 .- 1095-8630. ; 262
-
Tidskriftsartikel (refereegranskat)abstract
- Gilsonite as a natural occurrence of bitumen and due to the presence of carbon in its structure is a suitable adsorbent for a wide variety of pollutants. In this research, the adsorption of cyanide from the wastewater of gold processing plants using gilsonite were investigated. In this way, the effect of particle size of gilsonite, the weight and mixing time with solution, on the amount of cyanide adsorption have been studied. In addition, in one experiment, the effect of processed gilsonite on its adsorption ability was investigated. Based on the obtained results, the maximum adsorption of 61.64% was obtained in the size range of −1+0.5 and −2+1 mm of gilsonite. With increasing adsorbent weight and mixing time, the cyanide adsorption rate were increased. On the other hand, with the processing of the gilsonite sample, the amounts of adsorption were increased considerably. This study indicated that gilsonite can be used as an isolation and absorbent in the structure and floor of the tailing dumps of mineral processing plants.
|
|
| 9. |
- Bahrami, Ataallah, et al.
(författare)
-
Process mineralogy as a key factor affecting the flotation kinetics of copper sulfide minerals
- 2019
-
Ingår i: International Journal of Minerals, Metallurgy and Materials. - : Springer. - 1674-4799 .- 1869-103X. ; 26:4, s. 430-439
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of this study is to apply process mineralogy as a practical tool for further understanding and predicting the flotation kinetics of the copper sulfide minerals. The minerals’ composition and association, grain distribution, and liberation within the ore samples were analyzed in the feed, concentrate, and the tailings of the flotation processes with two pulp densities of 25wt% and 30wt%. The major copper-bearing minerals identified by microscopic analysis of the concentrate samples included chalcopyrite (56.2wt%), chalcocite (29.1wt%), covellite (6.4wt%), and bornite (4.7wt%). Pyrite was the main sulfide gangue mineral (3.6wt%) in the concentrates. A 95% degree of liberation with d80 > 80 µm was obtained for chalcopyrite as the main copper mineral in the ore sample. The recovery rate and the grade in the concentrates were enhanced with increasing chalcopyrite particle size. Chalcopyrite particles with a d80 of approximately 100 µm were recovered at the early stages of the flotation process. The kinetic studies showed that the kinetic second-order rectangular distribution model perfectly fit the flotation test data. Characterization of the kinetic parameters indicated that the optimum granulation distribution range for achieving a maximum flotation rate for chalcopyrite particles was between the sizes 50 and 55 µm.
|
|
| 10. |
- Bahrami, Ataallah, et al.
(författare)
-
The effect of grinding circuit efficiency on the grade and recovery of copper and molybdenum concentrates
- 2022
-
Ingår i: Energy Sources, Part A. - : Taylor & Francis Group. - 1556-7036 .- 1556-7230. ; 44:3, s. 8121-8134
-
Tidskriftsartikel (refereegranskat)abstract
- The efficiency of grinding and flotation process in copper-molybdenum processing circuit, largely affected by performance of thickeners and hydrocyclones devices. The goal of this paper is to investigate the effect of the rate-limiting factors on the performance of these devices and consequently on grinding and separation efficiency of the molybdenum processing circuit. So, a full process mineralogical study have been carried out on outputs of thickeners and hydrocyclone of the molybdenite flotation circuit. According to the results, coarse-grained fractions (>50 μm) of the planar molybdenite will not necessarily be recovered by thickener and hydrocyclones. This is especially true for hydrocyclones when the inlet-load rate is high, i.e., the erroneous discharge of planar molybdenite particles from the overflow of hydrocyclone, as well as their floatability in the thickener overflow, can be attributed to the effect of particle shape and size. This issue harms the grade and recovery of flotation due to the increase in the amount of circulating load (regrinding) and consequently the generation of fine particles (<10 μm) in the hydrocyclone-milling circuit. On the other hand, the almost spherical particles of copper minerals, as well as the nonplanar molybdenite fine-grained particles, are easily removed from the hydrocyclone underflow or settled in thickeners. The introduction of copper mineral particles into molybdenum concentrate and vice versa has reduced the quality of the produced concentrate and undesirable flotation performance.
|
|
