| 1. |
- Hedayati, Ali, 1984-, et al.
(författare)
-
Ash Transformation during Single-Pellet Combustion of Agricultural Biomass with a Focus on Potassium and Phosphorus
- 2021
-
Ingår i: Energy & Fuels. - : American Chemical Society (ACS). - 0887-0624 .- 1520-5029. ; 35:2, s. 1449-1464
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, ash transformation and release of critical ash-forming elements during single-pellet combustion of different types of agricultural opportunity fuels were investigated. The work focused on potassium (K) and phosphorus (P). Single pellets of poplar, wheat straw, grass, and wheat grain residues were combusted in a macro-thermogravimetric analysis reactor at three different furnace temperatures (600, 800, and 950 °C). In order to study the transformation of inorganic matters at different stages of the thermal conversion process, the residues were collected before and after full devolatilization, as well as after complete char conversion. The residual char/ash was characterized by scanning electron microscopy–energy-dispersive X-ray spectroscopy, X-ray diffraction, inductively coupled plasma, and ion chromatography, and the interpretation of results was supported by thermodynamic equilibrium calculations. During combustion of poplar, representing a Ca–K-rich woody energy crop, the main fraction of K remained in the residual ash primarily in the form of K2Ca(CO3)2 at lower temperatures and in a K–Ca-rich carbonate melt at higher temperatures. Almost all P retained in the ash and was mainly present in the form of hydroxyapatite. For the Si–K-rich agricultural biomass fuels with a minor (wheat straw) or moderate (grass) P content, the main fraction of K remained in the residual ash mostly in K–Ca-rich silicates. In general, almost all P was retained in the residual ash both in K–Ca–P–Si-rich amorphous structures, possibly in phosphosilicate-rich melts, and in crystalline forms as hydroxyapatite, CaKPO4, and calcium phosphate silicate. For the wheat grain, representing a K–P-rich fuel, the main fraction of K and P remained in the residual ash in the form of K–Mg-rich phosphates. The results showed that in general for all studied fuels, the main release of P occurred during the devolatilization stage, while the main release of K occurred during char combustion. Furthermore, less than 20% of P and 35% of K was released at the highest furnace temperature for all fuels.
|
|
| 2. |
- Hedayati, Ali, 1984-, et al.
(författare)
-
Ash transformation during single-pellet gasification of agricultural biomass with focus on potassium and phosphorus
- 2021
-
Ingår i: Fuel processing technology. - : Elsevier B.V.. - 0378-3820 .- 1873-7188. ; 217
-
Tidskriftsartikel (refereegranskat)abstract
- Agricultural biomasses and residues can play an important role in the global bioenergy system but their potential is limited by the risk of several ash-related problems such as deposit formation, slagging, and particle emissions during their thermal conversion. Therefore, a thorough understanding of the ash transformation reactions is required for this type of fuels. The present work investigates ash transformation reactions and the release of critical ash-forming elements with a special focus on K and P during the single-pellet gasification of different types of agricultural biomass fuels, namely, poplar, grass, and wheat grain residues. Each fuel was gasified as a single pellet at three different temperatures (600, 800, and 950 °C) in a Macro-TGA reactor. The residues from different stages of fuel conversion were collected to study the gradual ash transformation. Characterization of the residual char and ash was performed employing SEM-EDS, XRD, and ICP with the support of thermodynamic equilibrium calculations (TECs). The results showed that the K and P present in the fuels were primarily found in the residual char and ash in all cases for all studied fuels. While the main part of the K release occurred during the char conversion stage, the main part of the P release occurred during the devolatilization stage. The highest releases – less than 18% of P and 35% of K – were observed at the highest studied temperature for all fuels. These elements were present in the residual ashes as K2Ca(CO3)2 and Ca5(PO4)3OH for poplar; K-Ca-rich silicates and phosphosilicates in mainly amorphous ash for grass; and an amorphous phase rich in K-Mg-phosphates for wheat grain residues. © 2021 The Author(s)
|
|
| 3. |
- Maziarka, Przemyslaw, et al.
(författare)
-
Part 1─Impact of Pyrolysis Temperature and Wood Particle Length on Vapor Cracking and Char Porous Texture in Relation to the Tailoring of Char Properties
- 2024
-
Ingår i: Energy & Fuels. - 0887-0624 .- 1520-5029. ; 38:11, s. 9751-9771
-
Tidskriftsartikel (refereegranskat)abstract
- Pore size distribution is a key parameter in the performance of biobased pyrolytic char in novel applications. In industrial-scale production, the size of feedstock particles typically exceeds a few millimeters. For such particle sizes, it is a challenge to tailor the final properties of the char based only on the process conditions (experimental and modeling-wise). Pyrolysis studies of single particles larger than a few millimeters provide data sets useful for modeling and optimization of the process. Part 1 of this research focused on the pyrolysis of single particles of beech wood, secondary cracking, and its effect on the char porous texture. It contains a quantitative assessment of the effects of five conversion temperatures (from 300 to 840 °C) and two particle dimensions (Ø8 × 10 mm and Ø8 × 16 mm) on the composition of the pyrolysis vapors and pore morphology of the char. Results from real-time temperature and mass changes are presented along with release profiles of 15 vapor constituents measured by infrared spectroscopy. Furthermore, characterization of the collected bio-oil (using GC-MS/FID) and the textural hierarchical structured char (through N2 and CO2 adsorption, Hg porosimetry, and scanning electron microscopy (SEM)) was performed. Cracking of vapors above 500 °C was compound-specific. The polyaromatic hydrocarbons (PAHs) yield, between 680 and 840 °C, increased 5 times for 10 mm particles and 9 times for 16 mm ones. Besides temperature, PAH yield was suspected to correlate with particle length and PAHs/soot deposition in the micropores. Results showed that the macropores accounted for over 80% of the total pore volume, regardless of the temperature and particle length. Increasing the particle length by 60% caused a reduction in the specific surface area (ca. 15% at 840 °C) of the resulting char, mainly due to a reduction in microporosity. Based on the findings, the production conditions for a specific char application are suggested. The obtained data will be used in Part 2 of this research, devoted to subsequent CFD modeling of the process.
|
|
| 4. |
- Maziarka, Przemyslaw, et al.
(författare)
-
Tailoring of the pore structures of wood pyrolysis chars for potential use in energy storage applications
- 2021
-
Ingår i: Applied Energy. - : Elsevier BV. - 0306-2619 .- 1872-9118. ; 286
-
Tidskriftsartikel (refereegranskat)abstract
- Char obtained from biomass pyrolysis is an eco-friendly porous carbon, which has potential use as a material for electrodes in supercapacitors. For that application, a high microporous specific surface area (SSA) is desired, as it relates to the accessible surface for an applied electrolyte. Currently, the incomplete understanding of the relation between porosity development and production parameters hinders the production of tailor-made, bio-based pyrochars for use as electrodes. Additionally, there is a problem with the low reliability in assessing textual properties for bio-based pyrochars by gas adsorption. To address the aforementioned problems, beech wood cylinders of two different lengths, with and without pre-treatment with citric acid were pyrolysed at temperatures of 300-900 degrees C and analysed by gas adsorption. The pyrolyzed chars were characterised with adsorption with N-2 and CO2 to assess the influence of production parameters on the textual properties. The new approach in processing the gas adsorption data used in this study demonstrated the required consistency in assessing the micro- and mesoporosity. The SSA of the chars rose monotonically in the investigated range of pyrolysis temperatures. The pre-treatment with citric acid led to an enhanced SSA, and the length of the cylinders correlated with a reduced SSA. With pyrolysis at 900 degrees C, the micro-SSAs of samples with 10 mm increased by on average 717 +/- 32 m(2)/g. The trends among the investigated parameters and the textual properties were rationalized and provide a sound basis for further studies of tailor-made bio-based pyrochars as electrode materials in supercapacitors.
|
|
| 5. |
- Phounglamcheik, Aekjuthon, PhD student, 1989-, et al.
(författare)
-
CO2 Gasification Reactivity of Char from High-Ash Biomass
- 2021
-
Ingår i: ACS Omega. - : American Chemical Society (ACS). - 2470-1343. ; 6:49, s. 34115-34128
-
Tidskriftsartikel (refereegranskat)abstract
- Biomass char produced from pyrolysis processes is of great interest to be utilized as renewable solid fuels or materials. Forest byproducts and agricultural wastes are low-cost and sustainable biomass feedstocks. These biomasses generally contain high amounts of ash-forming elements, generally leading to high char reactivity. This study elaborates in detail how chemical and physical properties affect CO2 gasification rates of high-ash biomass char, and it also targets the interactions between these properties. Char produced from pine bark, forest residue, and corncobs (particle size 4–30 mm) were included, and all contained different relative compositions of ash-forming elements. Acid leaching was applied to further investigate the influence of inorganic elements in these biomasses. The char properties relevant to the gasification rate were analyzed, that is, elemental composition, specific surface area, and carbon structure. Gasification rates were measured at an isothermal condition of 800 °C with 20% (vol.) of CO2 in N2. The results showed that the inorganic content, particularly K, had a stronger effect on gasification reactivity than specific surface area and aromatic cluster size of the char. At the gasification condition utilized in this study, K could volatilize and mobilize through the char surface, resulting in high gasification reactivity. Meanwhile, the mobilization of Ca did not occur at the low temperature applied, thus resulting in its low catalytic effect. This implies that the dispersion of these inorganic elements through char particles is an important reason behind their catalytic activity. Upon leaching by diluted acetic acid, the K content of these biomasses substantially decreased, while most of the Ca remained in the biomasses. With a low K content in leached biomass char, char reactivity was determined by the active carbon surface area.
|
|
| 6. |
- Phounglamcheik, Aekjuthon, PhD student, 1989-, et al.
(författare)
-
Effects of Pyrolysis Conditions and Feedstocks on the Properties and Gasification Reactivity of Charcoal from Woodchips
- 2020
-
Ingår i: Energy & Fuels. - : American Chemical Society (ACS). - 0887-0624 .- 1520-5029. ; 34:7, s. 8353-8365
-
Tidskriftsartikel (refereegranskat)abstract
- Pyrolysis conditions in charcoal production affect yields, properties, and further use of charcoal. Reactivity is a critical property when using charcoal as an alternative to fossil coal and coke, as fuel or reductant, in different industrial processes. This work aimed to obtain a holistic understanding of the effects of pyrolysis conditions on the reactivity of charcoal. Notably, this study focuses on the complex effects that appear when producing charcoal from large biomass particles in comparison with the literature on pulverized biomass. Charcoals were produced from woodchips under a variety of pyrolysis conditions (heating rate, temperature, reaction gas, type of biomass, and bio-oil embedding). Gasification reactivity of produced charcoal was determined through thermogravimetric analysis under isothermal conditions of 850 degrees C and 20% of CO2. The charcoals were characterized for the elemental composition, specific surface area, pore volume and distribution, and carbon structure. The analysis results were used to elucidate the relationship between the pyrolysis conditions and the reactivity. Heating rate and temperature were the most influential pyrolysis parameters affecting charcoal reactivity, followed by the reaction gas and bio-oil embedding. The effects of these pyrolysis conditions on charcoal reactivity could primarily be explained by the difference in the meso- and macropore volume and the size and structural order of aromatic clusters. The lower reactivity of slow pyrolysis charcoals also coincided with their lower catalytic inorganic content. The reactivity difference between spruce and birch charcoals appears to be mainly caused by the difference in catalytically active inorganic elements. Contrary to pyrolysis of pulverized biomass, a low heating rate produced a higher specific surface area compared with a high heating rate. Furthermore, the porous structure and the reactivity of charcoal produced from woodchips were influenced when the secondary char formation was promoted, which cannot be observed in pyrolysis of pulverized biomass.
|
|
| 7. |
- Phounglamcheik, Aekjuthon, PhD student, 1989-, et al.
(författare)
-
Self-Heating of Biochar during Postproduction Storage by O2 Chemisorption at Low Temperatures
- 2022
-
Ingår i: Energies. - : MDPI. - 1996-1073. ; 15:1
-
Tidskriftsartikel (refereegranskat)abstract
- Biochar is attracting attention as an alternative carbon/fuel source to coal in the process industry and energy sector. However, it is prone to self-heating and often leads to spontaneous ignition and thermal runaway during storage, resulting in production loss and health risks. This study investigates biochar self-heating upon its contact with O2 at low temperatures, i.e., 50–300 °C. First, kinetic parameters of O2 adsorption and CO2 release were measured in a thermogravimetric analyzer using biochar produced from a pilot-scale pyrolysis process. Then, specific heat capacity and heat of reactions were measured in a differential scanning calorimeter. Finally, a one-dimensional transient model was developed to simulate self-heating in containers and gain insight into the influences of major parameters. The model showed a good agreement with experimental measurement in a closed metal container. It was observed that char temperature slowly increased from the initial temperature due to heat released during O2 adsorption. Thermal runaway, i.e., self-ignition, was observed in some cases even at the initial biochar temperature of ca. 200 °C. However, if O2 is not permeable through the container materials, the temperature starts decreasing after the consumption of O2 in the container. The simulation model was also applied to examine important factors related to self-heating. The results suggested that self-heating can be somewhat mitigated by decreasing the void fraction, reducing storage volume, and lowering the initial char temperature. This study demonstrated a robust way to estimate the cooling demands required in the biochar production process.
|
|
