| 1. |
- Afzal, Muhammad, et al.
(författare)
-
Fabrication of novel electrolyte-layer free fuel cell with semi-ionic conductor (Ba0.5Sr0.5Co0.8Fe0.2O3-delta- Sm0.2Ce0.8O1.9) and Schottky barrier
- 2016
-
Ingår i: Journal of Power Sources. - : Elsevier. - 0378-7753 .- 1873-2755. ; 328, s. 136-142
-
Tidskriftsartikel (refereegranskat)abstract
- Perovskite Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) is synthesized via a chemical co-precipitation technique for a low temperature solid oxide fuel cell (LTSOFC) (300-600 degrees C) and electrolyte-layer free fuel cell (EFFC) in a comprehensive study. The EFFC with a homogeneous mixture of samarium doped ceria (SDC): BSCF (60%:40% by weight) which is rather similar to the cathode (SDC: BSCF in 50%:50% by weight) used for a three layer SOFC demonstrates peak power densities up to 655 mW/cm(2), while a three layer (anode/ electrolyte/cathode) SOFC has reached only 425 mW/cm(2) at 550 degrees C. Chemical phase, crystal structure and morphology of the as-prepared sample are characterized by X-ray diffraction and field emission scanning electron microscopy coupled with energy dispersive spectroscopy. The electrochemical performances of 3-layer SOFC and EFFC are studied by electrochemical impedance spectroscopy (EIS). As-prepared BSCF has exhibited a maximum conductivity above 300 S/cm at 550 degrees C. High performance of the EFFC device corresponds to a balanced combination between ionic and electronic (holes) conduction characteristic. The Schottky barrier prevents the EFFC from the electronic short circuiting problem which also enhances power output. The results provide a new way to produce highly effective cathode materials for LTSOFC and semiconductor designs for EFFC functions using a semiconducting-ionic material.
|
|
| 2. |
- Battiston, S., et al.
(författare)
-
Influence of Al and Mg Addition on Thermoelectric Properties of Higher Manganese Silicides Obtained by Reactive Sintering
- 2017
-
Ingår i: Journal of Nanoscience and Nanotechnology. - : American Scientific Publishers. - 1533-4880 .- 1533-4899. ; 17:3, s. 1668-1673
-
Tidskriftsartikel (refereegranskat)abstract
- Higher manganese silicides (HMS), represented by MnSix (x = 1.71-1.75), are promising p-type candidates for thermoelectric (TE) energy harvesting systems at intermediate temperature range. The materials are very attractive as they may replace lead based compounds due to their nontoxicity, low cost of starting materials, and high thermal and chemical stability. Dense pellets were obtained through fast reactive sintering by spark plasma sintering (SPS). The addition -or nanoinclusion, of Al and Mg permitted the figure of merit enhancement of the material obtained with this technique, reaching the highest value of 0.40 at 600 degrees C. Morphology, composition and crystal structure of the samples were characterized by electron microscopies, energy dispersive X-ray spectroscopy, and X-ray diffraction analyses, respectively.
|
|
| 3. |
- Battiston, S., et al.
(författare)
-
Synthesis and Characterization of Al-Doped Mg2Si Thermoelectric Materials
- 2013
-
Ingår i: Journal of Electronic Materials. - New York : Springer. - 0361-5235 .- 1543-186X. ; 42:7, s. 1956-1959
-
Tidskriftsartikel (refereegranskat)abstract
- Magnesium silicide (Mg2Si)-based alloys are promising candidates for thermoelectric (TE) energy conversion for the middle to high range of temperature. These materials are very attractive for TE research because of the abundance of their constituent elements in the Earth's crust. Mg2Si could replace lead-based TE materials, due to its low cost, nontoxicity, and low density. In this work, the role of aluminum doping (Mg2Si:Al = 1:x for x = 0.005, 0.01, 0.02, and 0.04 molar ratio) in dense Mg2Si materials was investigated. The synthesis process was performed by planetary milling under inert atmosphere starting from commercial Mg2Si pieces and Al powder. After ball milling, the samples were sintered by means of spark plasma sintering to density > 95%. The morphology, composition, and crystal structure of the samples were characterized by field-emission scanning electron microscopy, energy-dispersive spectroscopy, and x-ray diffraction analyses. Moreover, Seebeck coefficient analyses, as well as electrical and thermal conductivity measurements were performed for all samples up to 600A degrees C. The resultant estimated ZT values are comparable to those reported in the literature for these materials. In particular, the maximum ZT achieved was 0.50 for the x = 0.01 Al-doped sample at 600A degrees C.
|
|
| 4. |
- Bitaraf Haghighi, Ehsan, et al.
(författare)
-
Cooling performance of nanofluids in a small diameter tube
- 2013
-
Ingår i: Experimental Thermal and Fluid Science. - : Elsevier. - 0894-1777 .- 1879-2286. ; 49, s. 114-122
-
Tidskriftsartikel (refereegranskat)abstract
- This article reports convective single-phase heat transfer performance in laminar flow for some selected nanofluids (NFs) in an open small diameter test section. A 0.50 mm inner diameter, 30 cm long stainless steel test section was used for screening single phase laminar convective heat transfer with water and five different water based NFs. Tested NFs were; Al2O3 (two types), TiO2 (two types) and CeO2 (one type), all 9 wt.% particle concentration. The effective thermal conductivity of the NFs were measured with Transient Plane Source (TPS) method and viscosity were measured with a rotating coaxial cylindrical viscometer. The obtained experimental results for thermal conductivity were in good agreement with the predicted values from Maxwell equation. The local Shah correlation, which is conventionally used for predicting convective heat transfer in laminar flow in Newtonian fluids with constant heat flux boundary condition, was shown to be valid for NFs. Moreover, the Darcy correlation was used to predict the friction factor for the NFs as well as for water. Enhancement in heat transfer for NFs was observed, when compared at equal Reynolds number, as a result of higher velocity or mass flow rate of the NFs at any given Reynolds number due to higher viscosity for NFs. However, when compared at equal pumping power no or only minor enhancement was observed.
|
|
| 5. |
- Bitaraf Haghighi, Ehsan, 1980-, et al.
(författare)
-
Measurement of temperature–dependent viscosity of nanofluids and its effect on pumping power in cooling systems
- 2013
-
Konferensbidrag (refereegranskat)abstract
- Nanofluids are engineered colloids of nanoparticlesdispersed homogenously in a base fluid, which theirthermophysical properties are changed by adding solidnanoparticles. Among the characteristic parameters,viscosity is one of the most important, as it directly affectsthe pumping power in cooling systems. In this study, theviscosity of water based Al2O3, ZrO2, and TiO2 (with 9wt%for all) nanofluids was measured and its impact on pressuredrop in a simple tubular pipe was estimated for bothlaminar and turbulent flow by classical correlations. Theeffect of temperature on the viscosity of these nanofluidswas also studied in the temperature range of 5˚C - 30˚C. Toassess the applicability of the classical correlations, pressuredrops across an open 30cm long, 0.50mm diameterstainless steel test section was measured for water andnanofluids by a differential pressure transducer. Theaverage viscosity increments compared to water in thetemperature range of 5˚C - 30˚C are 105%, 98% and 31% forAl2O3, ZrO2, and TiO2 nanofluids respectively. Moreover, theresults show that the viscosity of nanofluids decreases withthe increase of temperature; however the relative viscosity,which is defined as the viscosity ratio between a nanofluidand its base fluid is constant in 5˚C - 30˚C temperaturerange.
|
|
| 6. |
- Bitaraf Haghighi, Ehsan, et al.
(författare)
-
Shelf stability of nanofluids and its effect on thermal conductivity and viscosity
- 2013
-
Ingår i: Measurement science and technology. - : IOP Publishing. - 0957-0233 .- 1361-6501. ; 24:10, s. 105301-
-
Tidskriftsartikel (refereegranskat)abstract
- This study proposes a method and apparatus to estimate shelf stability of nanofluids. Nanofluids are fabricated by dispersion of solid nanoparticles in base fluids, and shelf stability is a key issue for many practical applications of these fluids. In this study, shelf stability is evaluated by measuring the weight of settled solid particles on a suspended tray in a colloid versus time and correlated with the performance change of some nanofluid systems. The effects of solid particle concentration and bath sonication time were investigated for selected nanofluids. The results show the applicability of this simple method and the apparatus to evaluate nanofluid shelf stability. Furthermore, it shows that Stokes' law is not valid for determining the settling time of the tested nanoparticles probably due to their complicated shape and presence of surface modifiers. The effect of shelf stability on thermal conductivity and viscosity was illustrated for some nanofluids. Experimental results show that water-based Al2O3 nanofluids have quite good shelf stability and can be good candidates for industrial applications.
|
|
| 7. |
- Burks, Terrance, 1969-, et al.
(författare)
-
Removal of Chromium(VI) Using Surface Modified Superparamagnetic Iron Oxide Nanoparticles
- 2013
-
Ingår i: Separation science and technology (Print). - : Informa UK Limited. - 0149-6395 .- 1520-5754. ; 48:8, s. 1243-1251
-
Tidskriftsartikel (refereegranskat)abstract
- This study describes the removal of Chromium(VI) from aqueous solutions using surface tailored superparamagnetic iron oxide nanoparticles (SPION) coated with bis(2,4,4-trimethylpentyl)dithiophosphinic acid (Cyanex-301). The synthesized Cyanex-301 coated SPION has been characterized by Transmission Electron Microscopy (TEM), Fourier-Transfer Infrared Spectroscopy (FT-IR), X-ray Photonic Spectroscopy (XPS), and Thermogravimetric Analysis (TGA). The adsorption mechanism was proposed to be via complexation between the thiol group on Cyanex-301 and Cr(VI) ions based on the XPS and FTIR analysis. It has been found that the equilibrium can be attained in less than 2hr. The adsorption behavior of Cr(VI) on the Cyanex-301 coated SPION can be well described by the Langmuir model and the maximum adsorption capacity for Cr(VI) was estimated to be 30.8mg/g. The selectivity of the Cyanex-301 coated SPION adsorbent towards Cr(VI) ions was found to be high and the maximum loading capacity obtained is up to an order of magnitude higher than that of other adsorbents reported in the literature. The desorption studies showed that more than 70% of Cr(VI) can be recovered using HNO3 as eluting solution. Our findings suggest a high potential of the designed adsorbent material for the treatment of industrial wastewater containing Cr(VI).
|
|
| 8. |
- Doddapaneni, Venkatesh, et al.
(författare)
-
Engineered PMMA-ZnO nanocomposites for improving the electric arc interruption capability in electrical switching applications : Unprecedented experimental insights
- 2017
-
Ingår i: Composites Science And Technology. - : Elsevier. - 0266-3538 .- 1879-1050. ; 141, s. 113-119
-
Tidskriftsartikel (refereegranskat)abstract
- Polymer inorganic nanocomposites (PINCs) have been engineered for controlling the electrical arc and to improve the arc interruption capability of the electrical switching applications, like circuit breakers. Several PINCs are fabricated by formation of ZnO quantum dots (QDs) in a poly (methyl methacrylate) (PMMA) matrix via in-situ polymerization method to avoid agglomeration of QDs, leading to a good spatial distribution of QDs in the polymer matrix. These PINCs have been characterized in detail for the morphology of QDs, interaction between QDs and polymer matrix, and ultraviolet (UV) radiation absorption. ZnO QDs have been assessed to have particle diameter of 3.5 nm, and their presence in the PMMA is revealed by the unique luminescence characteristics of the QDs under UV light. The presence of ZnO QDs broadened the range of UV radiation absorption of PMMA and the absorption edge is gradually shifted from 270 nm to 338 nm with step-wise loading of ZnO QDs. The PINCs are tested to determine their reproducibility and impact on the electrical arcs of current 1.6 kA generated using a specially designed test-setup. Interaction of PINCs with the electrical arcs generates ablation of chemical species towards core of the electrical arc, resulting in increase of voltage leading to cool-down the arc temperature. This experimental study demonstrates for the first time that these PINCs are reproducible, reliable and provides superior arc interruption capability.
|
|
| 9. |
- Doddapaneni, Venkatesh, et al.
(författare)
-
New experimental insights for controlling the electrical arcs in electrical switching applications : a comparative study on PMMA nanocomposites of Au and ZnO
- 2017
-
Ingår i: Composites Science And Technology. - : Elsevier. - 0266-3538 .- 1879-1050.
-
Tidskriftsartikel (övrigt vetenskapligt/konstnärligt)abstract
- Polymer inorganic nanocomposites (PINCs) are developed, not only due to scientific interest but also improving theelectric arc interruption process in the electrical switching applications like circuit breakers. The novelty of this work isin integrating the current developments in PINCs into electrical switching application in order to extend the limits of thepower switching devices. Several PINCs are fabricated by using pre-synthesized Au nanoparticles (NPs) of size 2.75 ±0.4 nm and poly (methyl methacrylate) (PMMA) matrix via in-situ polymerization method. Six homogeneous PINCsamples with ultra-low wt% of Au NPs varying from 0.0003 to 0.005 wt% have been fabricated. We find that thepresence of Au NPs improved the convective heat transfer and visible optical radiation absorption of PMMA. Thefabricated PINCs are tested for their arc interruption performance and the results are compared with ZnO PINCs in ourearlier work. The results of the experiments insights demonstrate the impact of PINCs on the electrical arcs and theirpotential advantages of having PINCs for the electric arc interruption process in high power switching devices.
|
|
| 10. |
- Doddapaneni, Venkatesh, et al.
(författare)
-
On the electrical arc interruption by using PMMA/iron oxide nanocomposites
- 2016
-
Ingår i: Materials Research Express. - : Institute of Physics (IOP). - 2053-1591. ; 3:10
-
Tidskriftsartikel (refereegranskat)abstract
- An experimental study is undertaken on the fabrication of poly (methyl methacrylate) (PMMA)/iron oxide nanocomposites to determine their potential use for electrical arc interruption in the electrical switching applications such as circuit breakers. Monodisperse iron oxide nanoparticles of average size ¡«11 nmare synthesized via thermal decomposition method and then homogeneously dispersed in the PMMAmatrix by in situ polymerization.PMMA/iron oxide nanocomposites with different nanoparticle loading have been fabricated to study the effect of loading content on the thermal energy absorption. Detailed physicochemical characterizations on synthesized material are performed using X-ray powder diffraction, scanning electron microscopy, TEM, thermogravimetric analysis and differential scanning calorimetry at different processing stages. Atest-setup was designed to evaluate the quality of the nanocomposites for electric arc interruption capability. The results showed that PMMA/iron oxide nanocomposites have a clear impact on the electric arc interruption and therefore should be considered as promising candidates for electrical switching applications.
|
|
