| 1. |
- Aboulfadl, Hisham, 1986, et al.
(författare)
-
Alkali Dispersion in (Ag,Cu)(In,Ga)Se2 Thin Film Solar Cells - Insight from Theory and Experiment
- 2021
-
Ingår i: ACS Applied Materials & Interfaces. - : American Chemical Society (ACS). - 1944-8252 .- 1944-8244. ; 13:6, s. 7188-7199
-
Tidskriftsartikel (refereegranskat)abstract
- Silver alloying of Cu(In,Ga)Se2 absorbers for thin film photovoltaics offers improvements in open-circuit voltage, especially when combined with optimal alkali-treatments and certain Ga concentrations. The relationship between alkali distribution in the absorber and Ag alloying is investigated here, combining experimental and theoretical studies. Atom probe tomography analysis is implemented to quantify the local composition in grain interiors and at grain boundaries. The Na concentration in the bulk increases up to ∼60 ppm for [Ag]/([Ag] + [Cu]) = 0.2 compared to ∼20 ppm for films without Ag and up to ∼200 ppm for [Ag]/([Ag] + [Cu]) = 1.0. First-principles calculations were employed to evaluate the formation energies of alkali-on-group-I defects (where group-I refers to Ag and Cu) in (Ag,Cu)(In,Ga)Se2 as a function of the Ag and Ga contents. The computational results demonstrate strong agreement with the nanoscale analysis results, revealing a clear trend of increased alkali bulk solubility with the Ag concentration. The present study, therefore, provides a more nuanced understanding of the role of Ag in the enhanced performance of the respective photovoltaic devices.
|
|
| 2. |
- Aboulfadl, Hisham, et al.
(författare)
-
Microstructural Characterization of Sulfurization Effects in Cu(In,Ga)Se2 Thin Film Solar Cells
- 2019
-
Ingår i: Microscopy and Microanalysis. - : CAMBRIDGE UNIV PRESS. - 1435-8115 .- 1431-9276. ; 25:2, s. 532-538
-
Tidskriftsartikel (refereegranskat)abstract
- Surface sulfurization of Cu(In,Ga)Se 2 (CIGSe) absorbers is a commonly applied technique to improve the conversion efficiency of the corresponding solar cells, via increasing the bandgap towards the heterojunction. However, the resulting device performance is understood to be highly dependent on the thermodynamic stability of the chalcogenide structure at the upper region of the absorber. The present investigation provides a high-resolution chemical analysis, using energy dispersive X-ray spectrometry and laser-pulsed atom probe tomography, to determine the sulfur incorporation and chemical re-distribution in the absorber material. The post-sulfurization treatment was performed by exposing the CIGSe surface to elemental sulfur vapor for 20 min at 500°C. Two distinct sulfur-rich phases were found at the surface of the absorber exhibiting a layered structure showing In-rich and Ga-rich zones, respectively. Furthermore, sulfur atoms were found to segregate at the absorber grain boundaries showing concentrations up to ∼7 at% with traces of diffusion outwards into the grain interior.
|
|
| 3. |
- Alberto, Helena, V, et al.
(författare)
-
Characterization of the Interfacial Defect Layer in Chalcopyrite Solar Cells by Depth-Resolved Muon Spin Spectroscopy
- 2022
-
Ingår i: Advanced Materials Interfaces. - : John Wiley & Sons. - 2196-7350. ; 9:19
-
Tidskriftsartikel (refereegranskat)abstract
- As devices become smaller and more complex, the interfaces between adjacent materials become increasingly important and are often critical to device performance. An important research goal is to improve the interface between the absorber and the window layer by inserting buffer layers to adjust the transition. Depth-resolved studies are key for a fundamental understanding of the interface. In the present experiment, the interface between the chalcopyrite Cu(In,Ga)Se-2 absorber and various buffer layers are investigated using low-energy muon spin rotation (mu SR) spectroscopy. Depth resolution in the nm range is achieved by implanting the muons with different energies so that they stop at different depths in the sample. Near the interface, a region about 50 nm wide is detected where the lattice is more distorted than further inside the absorber. The distortion is attributed to the long-range strain field caused by defects. These measurements allow a quantification of the corresponding passivation effect of the buffer layer. Bath-deposited cadmium sulfide provides the best defect passivation in the near interface region, in contrast to the dry-deposited oxides, which have a much smaller effect. The experiment demonstrates the great potential of low energy mu SR spectroscopy for microscopic interfacial studies of multilayer systems.
|
|
| 4. |
- Alberto, H. V., et al.
(författare)
-
Low energy muon study of the p-n interface in chalcopyrite solar cells
- 2023
-
Ingår i: Journal of Physics, Conference Series. - : Institute of Physics Publishing (IOPP). - 1742-6588 .- 1742-6596. ; 2462
-
Tidskriftsartikel (refereegranskat)abstract
- The slow muon technique was used to study the p-n junction of chalcopyrite solar cells. A defect layer near the interface was identified and the passivation of the defects by buffer layers was studied. Several cover layers on top of the chalcopyrite Cu(In,Ga)Se2 (CIGS) semiconductor absorber were investigated in this work, namely CdS, ZnSnO, Al2O3 and SiO2. Quantitative results were obtained: The defect layer extends about 50 nm into the CIGS absorber, the relevant disturbance is strain in the lattice, and CdS provides the best passivation, oxides have a minor effect. In the present contribution, specific aspects of the low-energy muon technique in connection with this research are discussed.
|
|
| 5. |
- Anacleto, Pedro, et al.
(författare)
-
Precisely nanostructured HfO2 rear passivation layers for ultra-thin Cu(In,Ga)Se-2
- 2022
-
Ingår i: Progress in Photovoltaics. - : John Wiley & Sons. - 1062-7995 .- 1099-159X. ; 30:11, s. 1289-1297
-
Tidskriftsartikel (refereegranskat)abstract
- The quest for material-efficient Cu(In,Ga)Se-2 (CIGS) solar cells encourages the development of ultra-thin absorbers. Their use reduces material consumption and energy usage during production by increasing the throughput. Thereby, both the bill of materials as well as the energy and capital costs are reduced. However, because thin absorbers are prone to increase back contact recombination, back surface passivation schemes are necessary to reach a similar or higher conversion efficiency than for absorbers with conventional thickness. Here, we investigate nanostructured hafnium oxide (HfO2) rear passivation layers for ultra-thin CIGS solar cells. We fabricate regular arrays of point contacts with 200 nm diameter through HfO2 layers with thicknesses between 7 and 40 nm using electron beam lithography and reactive ion etching. The current-voltage curves of solar cells with a 500 nm thick CIGS absorber layer and the nanostructured passivation layer show improved performance concerning V-oc and J(sc) compared to non-passivated reference devices. Furthermore, external quantum efficiency and optical reflection confirm an effective passivation behavior, with an average efficiency increase of up to 1.2% for the cells with the 40 nm thick HfO2 layer. In addition, simulation work shows that even 40 nm thick HfO2 passivation layers have only a minimal effect on the optical properties of ultra-thin CIGS solar cells, and hence, the photocurrent increase verified experimentally stems from electrical improvements caused by the HfO2 layer passivation effect. We also investigate the impact of ultra-thin (0.3, 0.6, 1.3, and 2.5 nm) non-patterned HfO2 passivation layers on the same type of solar cells. However, these results showed no improvement in solar cell performance, despite an increase in the current density with layer thickness.
|
|
| 6. |
- Bayrak Pehlivan, Ilknur, et al.
(författare)
-
Electrochromic solar water splitting using a cathodic WO3 electrocatalyst
- 2021
-
Ingår i: Nano Energy. - : Elsevier. - 2211-2855 .- 2211-3282. ; 81
-
Tidskriftsartikel (refereegranskat)abstract
- Solar-driven water splitting is an emerging technology with high potential to generate fuel cleanly and sustainably. In this work, we show that WO3 can be used as a cathodic electrocatalyst in combination with (Ag,Cu) InGaSe2 solar cell modules to produce hydrogen and provide electrochromic functionality to water splitting devices. This electrochromic effect can be used to monitor the charge state or performance of the catalyst for process control or for controlling the temperature and absorbed heat due to tunable optical modulation of the electrocatalyst. WO3 films coated on Ni foam, using a wide range of different sputtering conditions, were investigated as cathodic electrocatalysts for the water splitting reaction. The solar-to-hydrogen (STH) efficiency of solar-driven water electrolysis was extracted using (Ag,Cu)InGaSe2 solar cell modules with a cell band gap varied in between 1.15 and 1.25 eV with WO3 on Ni foam-based electrolyzers and yielded up to 13% STH efficiency. Electrochromic properties during water electrolysis were characterized for the WO3 films on transparent substrate (indium tin oxide). Transmittance varied between 10% and 78% and the coloration efficiency at a wavelength of 528 nm and the overpotential of 400 mV was 40 cm(2) C-1. Hydrogen ion consumption in ion intercalation for electrochromic and hydrogen gas production for water electrolysis processes was discussed.
|
|
| 7. |
- Bayrak Pehlivan, Ilknur, et al.
(författare)
-
NiMoV and NiO-based catalysts for efficient solar-driven water splitting using thermally integrated photovoltaics in a scalable approach
- 2021
-
Ingår i: iScience. - : Cell Press. - 2589-0042. ; 24:1
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, a trimetallic NiMoV catalyst is developed for the hydrogen evolution reaction and characterized with respect to structure, valence, and elemental distribution. The overpotential to drive a 10 mA cm−2 current density is lowered from 94 to 78 mV versus reversible hydrogen electrode by introducing V into NiMo. A scalable stand-alone system for solar-driven water splitting was examined for a laboratory-scale device with 1.6 cm2 photovoltaic (PV) module area to an up-scaled device with 100 cm2 area. The NiMoV cathodic catalyst is combined with a NiO anode in alkaline electrolyzer unit thermally connected to synthesized (Ag,Cu) (In,Ga)Se2 ((A)CIGS) PV modules. Performance of 3- and 4-cell interconnected PV modules, electrolyzer, and hydrogen production of the PV electrolyzer are examined between 25°C and 50°C. The PV-electrolysis device having a 4-cell (A)CIGS under 100 mW cm−2 illumination and NiMoV-NiO electrolyzer shows 9.1% maximum and 8.5% averaged efficiency for 100 h operation.
|
|
| 8. |
- Bayrak Pehlivan, Ilknur, et al.
(författare)
-
Optimum Band Gap Energy of ((Ag),Cu)(InGa)Se2 Materials for Combination with NiMo–NiO Catalysts for Thermally Integrated Solar-Driven Water Splitting Applications
- 2019
-
Ingår i: Energies. - : MDPI AG. - 1996-1073. ; 12
-
Tidskriftsartikel (refereegranskat)abstract
- Solar-driven water splitting is considered one of the promising future routes to generate fuel in a sustainable way. A carbon-free solar fuel, molecular hydrogen, can here be produced along two different but intimately related routes, photoelectrochemical (PEC) water splitting or photovoltaic electrolysis (PV-electrolysis), where the latter builds on well-established solar cell and electrolysis materials with high efficiency. The PV-electrolysis approach is also possible to construct from an integrated PEC/PV-system avoiding dc-dc converters and enabling heat exchange between the PV and electrolyzer part, to a conventionally wired PV-electrolysis system. In either case, the operating voltage at a certain current needs to be matched with the catalyst system in the electrolysis part. Here, we investigate ((Ag),Cu)(In,Ga)Se-2 ((A)CIGS)-materials with varying Ga-content modules for combination with NiMo-NiO catalysts in alkaline water splitting. The use of (A)CIGS is attractive because of the low cost-to-performance ratio and the possibility to optimize the performance of the system by tuning the band gap of (A)CIGS in contrast to Si technology. The band gap tuning is possible by changing the Ga/(Ga + In) ratio. Optoelectronic properties of the (A)CIGS materials with Ga/(Ga + In) ratios between 0.23 and 0.47 and the voltage and power output from the resulting water splitting modules are reported. Electrolysis is quantified at temperatures between 25 and 60 degrees C, an interval obtainable by varying the thermal heat exchange form a 1-sun illuminated PV module and an electrolyte system. The band gaps of the (A)CIGS thin films were between 1.08 to 1.25 eV and the three-cell module power conversion efficiencies (PCE) ranged from 16.44% with 1.08 eV band gap and 19.04% with 1.17 eV band gap. The highest solar-to-hydrogen (STH) efficiency was 13.33% for the (A)CIGS-NiMo-NiO system with 17.97% module efficiency and electrolysis at 60 degrees C compared to a STH efficiency of 12.98% at 25 degrees C. The increase in STH efficiency with increasing temperature was more notable for lower band gaps as these are closer to the overpotential threshold for performing efficient solar-driven catalysis, while only a modest improvement can be obtained by utilizing thermal exchange for a band gap matched PV-catalysts system. The results show that usage of cost-effective and stable thin film PV materials and earth abundant catalysts can provide STH efficiencies beyond 13% even with PV modules with modest efficiency.
|
|
| 9. |
- Bayrak Pehlivan, Ilknur, et al.
(författare)
-
The climatic response of thermally integrated photovoltaic-electrolysis water splitting using Si and CIGS combined with acidic and alkaline electrolysis
- 2020
-
Ingår i: Sustainable Energy & Fuels. - : ROYAL SOC CHEMISTRY. - 2398-4902. ; 4:12, s. 6011-6022
-
Tidskriftsartikel (refereegranskat)abstract
- The Horizon 2020 project PECSYS aims to build a large area demonstrator for hydrogen production from solar energy via integrated photovoltaic (PV) and electrolysis systems of different types. In this study, Si- and CIGS-based photovoltaics are developed together with three different electrolyzer systems for use in the corresponding integrated devices. The systems are experimentally evaluated and a general model is developed to investigate the hydrogen yield under real climatic conditions for various thin film and silicon PV technologies and electrolyser combinations. PV characteristics using a Si heterojunction (SHJ), thin film CuInxGa1-xSe2, crystalline Si with passivated emitter rear totally diffused and thin film Si are used together with temperature dependent catalyst load curves from both acidic and alkaline approaches. Electrolysis data were collected from (i) a Pt-IrO2-based acidic electrolysis system, and (ii) NiMoW-NiO-based and (iii) Pt-Ni foam-based alkaline electrolysis systems. The calculations were performed for mid-European climate data from Julich, Germany, which will be the installation site. The best systems show an electricity-to-hydrogen conversion efficiency of 74% and over 12% solar-to-hydrogen (STH) efficiencies using both acidic and alkaline approaches and are validated with a smaller lab scale prototype. The results show that the lower power delivered by all the PV technologies under low irradiation is balanced by the lower demand for overpotentials for all the electrolysis approaches at these currents, with more or less retained STH efficiency over the full year if the catalyst area is the same as the PV area for the alkaline approach. The total yield of hydrogen, however, follows the irradiance, where a yearly hydrogen production of over 35 kg can be achieved for a 10 m(2) integrated PV-electrolysis system for several of the PV and electrolyser combinations that also allow a significant (100-fold) reduction in necessary electrolyser area for the acidic approach. Measuring the catalyst systems under intermittent and ramping conditions with different temperatures, a 5% lowering of the yearly hydrogen yield is extracted for some of the catalyst systems while the Pt-Ni foam-based alkaline system showed unaffected or even slightly increased yearly yield under the same conditions.
|
|
| 10. |
- Bilousov, Oleksandr V., et al.
(författare)
-
ALD of phase controlled tin monosulfide thin films
- 2017
-
Konferensbidrag (refereegranskat)abstract
- Tin monosulfide (SnS) is a promising semiconductor material for low-cost conversion of solar energy, playing the role of absorber layer in photovoltaic devices. SnS is, due to its high optical damping, also an excellent semiconductor candidate for the realization of ultrathin (nanoscale thickness) plasmonic solar cells [1].Here, we present an important step to further control and understand SnS film properties produced using low temperature ALD with Sn(acac)2 and H2S as precursors. We show that the SnS film properties vary over a rather wide range depending on substrate temperature and reaction conditions, and that this is connected to the growth of cubic (π-SnS) and orthorhombic SnS phases. The optical properties of the two polymorphs differ significantly, as demonstrated by spectroscopic ellipsometry [2].1. C. Hägglund, G. Zeltzer, R. Ruiz, A. Wangperawong, K. E. Roelofs, S. F. Bent, ACS Photonics 3 (3) (2016) 456–463.2. O. V. Bilousov, Y. Ren, T. Törndahl, O. Donzel-Gargand , T. Ericson, C. Platzer-Björkman, M. Edoff, and C. Hägglund, ACS Chemistry of Materials 29 (7) (2017) 2969–2978.
|
|
| 11. |
- Bilousov, Oleksandr V., et al.
(författare)
-
Atomic Layer Deposition of Cubic and Orthorhombic Phase Tin Monosulfide
- 2017
-
Ingår i: Chemistry of Materials. - : AMER CHEMICAL SOC. - 0897-4756 .- 1520-5002. ; 29:7, s. 2969-2978
-
Tidskriftsartikel (refereegranskat)abstract
- Tin monosulfide (SnS) is a promising light-absorbing material with weak environmental constraints for application in thin film solar cells. In this paper, we present low-temperature atomic layer deposition (ALD) of high-purity SnS of both cubic and orthorhombic phases. Using tin(II) 2,4-pentanedionate [Sn(acac)(2)] and hydrogen sulfide (H2S) as precursors, controlled growth of the two polymorphs is achieved. Quartz crystal microbalance measurements are used to establish saturated conditions and show that the SnS ALD is self-limiting over temperatures from at least 80 to 160 degrees C. In this temperature window, a stable mass gain of 19 ng cm(-2) cycle(-1) is observed. The SnS thin film crystal structure and morphology undergo significant changes depending on the conditions. High-resolution transmission electron microscopy and X-ray diffraction demonstrate that fully saturated growth requires a large H2S dose and results in the cubic phase. Smaller H2S doses and higher temperatures favor the orthorhombic phase. The optical properties of the two polymorphs differ significantly, as demonstrated by spectroscopic ellipsometry. The orthorhombic phase displays a wide (0.3-0.4 eV) Urbach tail in the near-infrared region, ascribed to its nanoscale structural disorder and/or to sulfur vacancy-induced gap states. In contrast, the cubic phase is smooth and void-free and shows a well-defined, direct forbidden-type bandgap of 1.64 eV.
|
|
| 12. |
- Bose, Sourav, et al.
(författare)
-
A morphological and electronic study of ultrathin rear passivated Cu(In,Ga)Se2 solar cells
- 2019
-
Ingår i: Thin Solid Films. - : Elsevier BV. - 0040-6090 .- 1879-2731. ; 671, s. 77-84
-
Tidskriftsartikel (refereegranskat)abstract
- The effects of introducing a passivation layer at the rear of ultrathin Copper Indium Gallium di-Selenide Cu(In,Ga)Se2 (CIGS) solar cells is studied. Point contact structures have been created on 25 nm Al2O3 layer using e-beam lithography. Reference solar cells with ultrathin CIGS layers provide devices with average values of light to power conversion efficiency of 8.1% while for passivated cells values reached 9.5%. Electronic properties of passivated cells have been studied before, but the influence of growing the CIGS on Al2O3 with point contacts was still unknown from a structural and morphological point of view. Scanning Electron Microscopy, X-ray Diffraction and Raman spectroscopy measurements were performed. These measurements revealed no significant morphological or structural differences in the CIGS layer for the passivated samples compared with reference samples. These results are in agreement with the similar values of carrier density (~8 x 1016 cm-3) and depletion region (~160 nm) extracted using electrical measurements. A detailed comparison between both sample types in terms of current-voltage, external quantum efficiency and photoluminescence measurements show very different optoelectronic behaviour which is indicative of a successful passivation. SCAPS simulations are done to explain the observed results in view of passivation of the rear interface.
|
|
| 13. |
- Böhnke, Tobias, et al.
(författare)
-
Copper indium gallium diselenide thin films for sun angle detectors in space applications
- 2009
-
Ingår i: Thin Solid Films. - : Elsevier BV. - 0040-6090 .- 1879-2731. ; 517:6, s. 2063-2068
-
Tidskriftsartikel (refereegranskat)abstract
- This work reports on processing, analysis and characterization of copper indium gallium diselenide (CIGS)used as a photosensitive layer for sensors such as sun angle detectors in space applications. CIGS-based solarcell devices with different CIGS layer thicknesses and the pn-junction located on the opposite side of theincidence of light were illuminated through their ultra-thin transparent molybdenum back contacts. Theresults from the current density versus voltage and quantum efficiency measurement indicate that the CIGSabsorber layer may not exceed 750 nm at backside illumination, due to the limited CIGS diffusion length.
|
|
| 14. |
- Calnan, Sonya, et al.
(författare)
-
Development of Various Photovoltaic‐Driven Water Electrolysis Technologies for Green Solar Hydrogen Generation
- 2021
-
Ingår i: Solar RRL. - : John Wiley & Sons. - 2367-198X. ; 6:5
-
Tidskriftsartikel (refereegranskat)abstract
- Direct solar hydrogen generation via a combination of photovoltaics (PV) and water electrolysis can potentially ensure a sustainable energy supply while minimizing greenhouse emissions. The PECSYS project aims at demonstrating asolar-driven electrochemical hydrogen generation system with an area >10 m2 with high efficiency and at reasonable cost. Thermally integrated PV electrolyzers(ECs) using thin-film silicon, undoped, and silver-doped Cu(In,Ga)Se2 and silicon heterojunction PV combined with alkaline electrolysis to form one unit are developed on a prototype level with solar collection areas in the range from 64 to2600 cm2 with the solar-to-hydrogen (StH) efficiency ranging from 4 to 13%. Electrical direct coupling of PV modules to a proton exchange membrane EC test the effects of bifacially (730 cm2 solar collection area) and to study the long-term operation under outdoor conditions (10 m2 collection area) is also investigated. In both cases, StH efficiencies exceeding 10% can be maintained over the test periods used. All the StH efficiencies reported are based on measured gas outflow using mass flow meters.
|
|
| 15. |
- Cunha, Jose M., V, et al.
(författare)
-
Decoupling of Optical and Electrical Properties of Rear Contact CIGS Solar Cells
- 2019
-
Ingår i: IEEE Journal of Photovoltaics. - : Institute of Electrical and Electronics Engineers (IEEE). - 2156-3381 .- 2156-3403. ; 9:6, s. 1857-1862
-
Tidskriftsartikel (refereegranskat)abstract
- A novel architecture that comprises rear interface passivation and increased rear optical reflection is presented with the following advantages: i) enhanced optical reflection is achieved by the deposition of a metallic layer over the Mo rear contact; ii) improved interface qualitywithCIGS by adding a sputteredAl 2O 3 layer over the metallic layer; and, iii) optimal ohmic electrical contact ensured by rear-openings refilling with a second layer of Mo as generally observed from the growth of CIGS on Mo. Hence, a decoupling between the electrical function and the optical purpose of the rear substrate is achieved. We present in detail the manufacturing procedure of such type of architecture together with its benefits and caveats. A preliminary analysis showing an architecture proof-of-concept is presented and discussed.
|
|
| 16. |
- Cunha, Jose M. V., et al.
(författare)
-
High-Performance and Industrially Viable Nanostructured SiOx Layers for Interface Passivation in Thin Film Solar Cells
- 2021
-
Ingår i: Solar RRL. - : John Wiley & Sons. - 2367-198X. ; 5:3
-
Tidskriftsartikel (refereegranskat)abstract
- Herein, it is demonstrated, by using industrial techniques, that a passivation layer with nanocontacts based on silicon oxide (SiOx) leads to significant improvements in the optoelectronical performance of ultrathin Cu(In,Ga)Se-2 (CIGS) solar cells. Two approaches are applied for contact patterning of the passivation layer: point contacts and line contacts. For two CIGS growth conditions, 550 and 500 degrees C, the SiOx passivation layer demonstrates positive passivation properties, which are supported by electrical simulations. Such positive effects lead to an increase in the light to power conversion efficiency value of 2.6% (absolute value) for passivated devices compared with a nonpassivated reference device. Strikingly, both passivation architectures present similar efficiency values. However, there is a trade-off between passivation effect and charge extraction, as demonstrated by the trade-off between open-circuit voltage (V-oc) and short-circuit current density (J(sc)) compared with fill factor (FF). For the first time, a fully industrial upscalable process combining SiOx as rear passivation layer deposited by chemical vapor deposition, with photolithography for line contacts, yields promising results toward high-performance and low-cost ultrathin CIGS solar cells with champion devices reaching efficiency values of 12%, demonstrating the potential of SiOx as a passivation material for energy conversion devices.
|
|
| 17. |
- Cunha, J. M. V., et al.
(författare)
-
Insulator Materials for Interface Passivation of Cu(In,Ga)Se-2 Thin Films
- 2018
-
Ingår i: IEEE Journal of Photovoltaics. - : IEEE-INST ELECTRICAL ELECTRONICS ENGINEERS INC. - 2156-3381 .- 2156-3403. ; 8:5, s. 1313-1319
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, metal-insulator-semiconductor structures were fabricated in order to study different types of insulators, namely, aluminum oxide (Al2O3), silicon nitride, and silicon oxide (SiOx) to be used as passivation layers in Cu(In,Ga)Se-2 (CIGS) thin-film solar cells. The investigated stacks consisted of SLG/Mo/CIGS/insulator/Al. Raman scattering and photoluminescence measurements were done to verify the insulator deposition influence on the CIGS surface. In order to study the electrical properties of the CIGS-insulator interface, capacitance versus conductance and voltage (C-G-V) measurements were done to estimate the number and polarity of fixed insulator charges (Q(f)). The density of interface defects (D-it) was estimated from capacitance versus conductance and frequency (C-G-f) measurements. This study evidences that the deposition of the insulators at high temperatures (300 degrees C) and the use of a sputtering technique cause surface modification on the CIGS surface. We found that, by varying the SiOx deposition parameters, it is possible to have opposite charges inside the insulator, which would allow its use in different device architectures. The material with lower Dit values was Al2O3 when deposited by sputtering.
|
|
| 18. |
- Donzel-Gargand, Olivier, et al.
(författare)
-
Cu-depleted patches induced by presence of K during growth of CIGS absorbers
- 2017
-
Konferensbidrag (refereegranskat)abstract
- The conversion efficiency of the CIGS thin film solar cells has rapidly increased since introduction of the heavier alkali-doping (K, Rb, Cs). While the exclusive introduction of Na in the CIGS films has led to efficiencies up to 20,4% 1, the latest K, Rb or Cs post deposition treatments (PDT) have increased the efficiency to 22,6% 2. The exact role of this heavy-alkali PDT is still under discussion but three explanations have been discussed in the literature. First, that the heavy alkali PDT facilitates CdCu substitution, that results in an enhanced absorber type inversion, moving the p-n junction further into the CIGS bulk 3. Second, that the main effect from heavy alkali PDT is due to the formation of a K-In-Se2 layer, that passivates defects at the CIGS surface, reducing interface recombination 4. And third, that the heavy alkali PDT induces a Cu depletion at the surface of the CIGS which, by increasing the local Fermi level, increases the band bending; thus creating a higher potential barrier for holes to recombine 5.
|
|
| 19. |
- Donzel-Gargand, Olivier, et al.
(författare)
-
Deep surface Cu depletion induced by K in high-efficiency Cu(In,Ga)Se2 solar cell absorbers
- 2018
-
Ingår i: Progress in Photovoltaics. - : Wiley. - 1062-7995 .- 1099-159X. ; 26:9, s. 730-739
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, we used K‐rich glass substrates to provide potassium during the coevaporation of Cu(In,Ga)Se2 (CIGS) absorber layers. Subsequently, we applied a postdeposition treatment (PDT) using KF or RbF to some of the grown absorbers. It was found that the presence of K during the growth of the CIGS layer led to cell effi- ciencies beyond 17%, and the addition of a PDT pushed it beyond 18%. The major finding of this work is the observation of discontinuous 100‐ to 200‐nm‐deep Cu‐ depleted patches in the vicinity of the CdS buffer layer, correlated with the presence of K during the growth of the absorber layer. The PDT had no influence on the forma- tion of these patches. A second finding concerns the composition of the Cu‐depleted areas, where an anticorrelation between Cu and both In and K was measured using scanning transmission electron microscopy. Furthermore, a steeper Ga/(In+Ga) ratio gradient was measured for the absorbers grown with the presence of K, suggesting that K hinders the group III element interdiffusion. Finally, no Cd in‐diffusion to the CIGS layer could be detected. This indicates that if CdCu substitution occurs, either their concentration is below our instrumental detection limit or its presence is contained within the first 6 nm from the CdS/CIGS interface.
|
|
| 20. |
- Donzel-Gargand, Olivier, et al.
(författare)
-
Secondary phase formation and surface modification from a high dose KF-post deposition treatment of (Ag,Cu)(In,Ga)Se-2 solar cell absorbers
- 2019
-
Ingår i: Progress in Photovoltaics. - : Wiley. - 1062-7995 .- 1099-159X. ; 27:3, s. 220-228
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, we assessed the potential of KF-post deposition treatment (PDT) performed on a silver-alloyed Cu (In,Ga)Se-2 (ACIGS) solar absorber. ACIGS absorbers with Ag/Ag + Cu ratio (Ag/I) close to 20% were co-evaporated on a Mo-coated glass substrate and exposed to in-situ KF-PDT of various intensities. The current-voltage characteristics indicated that an optimized PDT can be beneficial, increasing in our study the median V-oc and efficiency values by +48 mV and + 0.9%(abs) (from 728 mV and 16.1% efficiency measured for the sample without PDT), respectively. However, an increased KF-flux during PDT resulted in a net deterioration of the performance leading to median V-oc and efficiency values as low as 503 mV and 4.7%. The chemical composition analysis showed that while the reference absorber without any post deposition treatment (PDT) was homogeneous, the KF-PDT induced a clear change within the first 10 nm from the surface. Here, the surface layer composition was richer in K and In with an increased Ag/I ratio, and its thickness seemed to follow the KF exposure intensity. Additionally, high-dose KF-PDT resulted in substantial formation of secondary phases for the ACIGS. The secondary phase precipitates were also richer in Ag, K, and In, and electron and X-ray diffraction data match with the monoclinic C 1 2/c 1 space group adopted by the Ag-alloyed KInSe2 phase. It could not be concluded whether the performance loss for the solar cell devices originated from the thicker surface layer or the presence of secondary phases, or both for the high-dose KF-PDT sample.
|
|
| 21. |
- Donzel-Gargand, Olivier, et al.
(författare)
-
Surface Modification And Secondary Phase Formation From a High Dose KF-Post Deposition Treatment of (Ag,Cu)(In,Ga)Se2 Solar Cell Absorbers
-
Ingår i: Progress in Photovoltaics. - 1062-7995 .- 1099-159X.
-
Tidskriftsartikel (refereegranskat)abstract
- In this study we assessed the potential of KF-Post Deposition Treatment (PDT) performed on a silver-alloyed Cu(Inx,Ga1-x)Se2 (ACIGS) solar absorber. ACIGS absorbers with Ag/Ag+Cu ratio (Ag/I) close to 20% were co-evaporated on a Mo-coated glass substrate and exposed to in-situ KF-PDT of various intensities. The current-voltage characteristics indicated that an optimized PDT can be beneficial, increasing in our study the median Voc and efficiency values by +48 mV and +0.9 %abs (from 728 mV and 16.1 % efficiency measured for the sample without PDT), respectively. However, an increased KF-flux during PDT resulted in a net deterioration of the performance leading to median Voc and efficiency values as low as 503 mV and 4.7 %. The chemical composition analysis showed that while the reference absorber without any PDT was homogeneous, the KF-PDT induced a clear change within the first 10 nm from the surface. Here, the surface layer composition was richer in K and In with an increased Ag/I ratio, and its thickness seemed to follow the KF exposure intensity. Additionally, high-dose KF-PDT resulted in substantial formation of secondary phases for the ACIGS. The secondary phase precipitates were also richer in Ag, K and In, and Electron and X-ray diffraction data match with the monoclinic C 1 2/c 1 space group adopted by the Ag-alloyed KInSe2 (AKIS) phase. It could not be concluded whether the performance loss for the solar cell devices originated from the thicker surface layer or the presence of secondary phases, or both for the high-dose KF-PDT sample.
|
|
| 22. |
- Donzel-Gargand, Olivier, 1986-
(författare)
-
The Multiple Faces of Interfaces : Electron microscopy analysis of CuInSe2 thin-film solar cells
- 2018
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The CIS solar cell family features both a high stability and world-class performances. They can be deposited on a wide variety of substrates and absorb the entire solar spectrum only using a thickness of a few micrometers. These particularities allow them to feature the most positive Energy returned on energy invested (EROI) values and the shortest Energy payback times (EPBT) of all the main photovoltaic solar cells. Using mainly electron microscopy characterization techniques, this thesis has explored the questions related to the interface control in thin-film photovoltaic solar cells based on CuInSe2 (CIS) absorber materials. Indeed, a better understanding of the interfaces is essential to further improve the solar cell conversion efficiency (currently around 23%), but also to introduce alternative substrates, to implement various alloying (Ga-CIS (CIGS), Ag-CIGS (ACIGS)…) or even to assess alternative buffer layers.The thread of this work is the understanding and the improvement of the interface control. To do so, the passivation potential of Al2O3 interlayers has been studied in one part of the thesis. While positive changes were generally measured, a subsequent analysis has revealed that a detrimental interaction could occur between the NaF precursor layer and the rear Al2O3 passivation layer. Still within the passivation research field, incorporation of various alkali-metals to the CIS absorber layer has been developed and analyzed. Large beneficial effects were ordinarily reported. However, similar KF-post deposition treatments were shown to be potentially detrimental for the silver-alloyed CIGS absorber layer. Finally, part of this work dealt with the limitations of the thin-barrier layers usually employed when using steel substrates instead of soda-lime glass ones. The defects and their origin could have been related to the steel manufacturing process, which offered solutions to erase them.Electron microscopy, especially Transmission electron microscopy (TEM), was essential to scrutinize the local changes occurring at the different interfaces within a few nanometers. The composition variation was measured with both Electron energy loss spectroscopy (EELS) and Energy dispersive X-ray spectroscopy (EDS) techniques. Finally, efforts have been invested in controlling and improving the FIB sample preparation, which was required for the TEM observations in our case.
|
|
| 23. |
- Edoff, Marika, 1965-, et al.
(författare)
-
Back Contact Passivation Effects in Bi-Facial Thin CIGS Solar Cells
- 2016
-
Ingår i: 2016 IEEE 43rd Photovoltaic Specialists Conference (PVSC). - : IEEE. - 9781509027248 ; , s. 3527-3529
-
Konferensbidrag (refereegranskat)abstract
- Bi-facial solar cells with ultrathin CIGS solar cells are fabricated to investigate the influence of back contact passivation. Solar cells with CIGS thicknesses of 300 and 500 nm and with an ultrathin transparent Mo layer are characterized using EQE measurements from both the front and the rear side as well as with I-V measurements. Back contact passivation consisting of Al2O3 deposited by atomic layer deposition and nano-sized point contact openings is used. The results are compared to cells with only the transparent Mo layer as back contact. We find a significant effect of the passivation manifested as an increase in the current density of the solar cells with the passivation.
|
|
| 24. |
- Edoff, Marika, 1965-, et al.
(författare)
-
High Voc in (Cu,Ag)(In,Ga)Se2 Solar Cells
- 2017
-
Ingår i: IEEE Journal of Photovoltaics. - 2156-3381 .- 2156-3403. ; 7:6, s. 1789-1794
-
Tidskriftsartikel (refereegranskat)abstract
- In this contribution, we show that silver substitution for copper in Cu(In,Ga)Se-2 (CIGS) to form (Ag,Cu)(In, Ga)Se-2 (ACIGS) leads to a reduction of the voltage loss expressed as E-g/q-V-oc. This, in turn, leads to higher device efficiencies as compared to similar CIGS devices without Ag. We report V-oc at 814 mV at a conversion efficiency of 21% for our best ACIGS device with 20% of the group I element consisting of silver. Comparing ACIGS and CIGS devices with the same Ga/(Ga+ In) ratio, the ACIGS devices exhibit about 0.05 eV higher bandgap. Alkali postdeposition treatment with KF leads to improvements in efficiency both for CIGS and ACIGS, but we find that the dose of KF needed for optimum device for ACIGS is 10-20% of the dose used for CIGS.
|
|
| 25. |
- Edoff, Marika, 1965-, et al.
(författare)
-
Post Deposition Treatments of (Ag,Cu)(In,Ga)Se-2 Thin Films for Solar Cells
- 2019
-
Ingår i: 2019 IEEE 46th Photovoltaic Specialists Conference (PVSC). - New York : IEEE. - 9781728104942 ; , s. 618-621
-
Konferensbidrag (refereegranskat)abstract
- Different alkali alternatives for post-deposition of ACIGS were tested, both conventional fluoride salts and in the form of metals. XPS analysis of surfaces treated with K or KF as well as Rb or RbF have been performed, before (only for K and Rb) and after an ammonia etch. In addition to a strong suppression of Cu and Ag near the surface, we observe a difference in the re-distribution of Ga in the surface region after the etch depending on pdt element. Our results are consistent with the formation of K-In-Se and Rb-In-Se compounds for both metal alkalis and alkali fluorides. We find a similar beneficial effect on cell performance for the best cells with the metals as with the fluoride salts.
|
|
