1. |
- Admassie, Shimelis, et al.
(author)
-
A renewable biopolymer cathode with multivalent metal ions for enhanced charge storage
- 2014
-
In: JOURNAL OF MATERIALS CHEMISTRY A. - : Royal Society of Chemistry. - 2050-7488. ; 2:6, s. 1974-1979
-
Journal article (peer-reviewed)abstract
- A ternary composite supercapacitor electrode consisting of phosphomolybdic acid (HMA), a renewable biopolymer, lignin, and polypyrrole was synthesized by a simple one-step simultaneous electrochemical deposition and characterized by electrochemical methods. It was found that the addition of HMA increased the specific capacitance of the polypyrrole-lignin composite from 477 to 682 F g(-1) ( at a discharge current of 1 A g(-1)) and also significantly improved the charge storage capacity from 6(to 128 mA h g(-1).
|
|
2. |
- Bao, Qinye, et al.
(author)
-
Effects of ultraviolet soaking on surface electronic structures of solution processed ZnO nanoparticle films in polymer solar cells
- 2014
-
In: Journal of Materials Chemistry A. - : Royal Society of Chemistry. - 2050-7488. ; 2:41, s. 17676-17682
-
Journal article (peer-reviewed)abstract
- We systematically show the effect of UV-light soaking on surface electronic structures and chemical states of solution processed ZnO nanoparticle (ZnONP) films in UHV, dry air and UV-ozone. UV exposure in UHV induces a slight decrease in work function and surface-desorption of chemisorbed oxygen, whereas UV exposure in the presence of oxygen causes an increase in work function due to oxygen atom vacancy filling in the ZnO matrix. We demonstrate that UV-light soaking in combination with vacuum or oxygen can tune the work function of the ZnONP films over a range exceeding 1 eV. Based on photovoltaic performance and diode measurements, we conclude that the oxygen atom vacancy filling occurs mainly at the surface of the ZnONP films and that the films consequently retain their n-type behavior despite a significant increase in the measured work function.
|
|
3. |
|
|
4. |
- Bao, Qinye, et al.
(author)
-
Energy Level Alignment of N-Doping Fullerenes and Fullerene Derivatives Using Air-Stable Dopant
- 2017
-
In: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 9:40, s. 35476-35482
-
Journal article (peer-reviewed)abstract
- Doping has been proved to be one of the powerful technologies to achieve significant improvement in the performance of organic electronic devices. Herein, we systematically map out the interface properties of solution-processed air-stable n-type (4(1,3-dimethyl-2,3-dihydro-1H-benzoimidazol-2-yl)phenyl) doping fullerenes and fullerene derivatives and establish a universal energy level alignment scheme for this class of n-doped system. At low doping levels at which the charge-transfer doping induces mainly bound charges, the energy level alignment of the n-doping organic semiconductor can be described by combining integer charger transfer-induced shifts with a so-called double-dipole step. At high doping levels, significant densities of free charges are generated and the charge flows between the organic film and the conducting electrodes equilibrating the Fermi level in a classic "depletion layer" scheme. Moreover, we demonstrate that the model holds for both n- and p-doping of pi-backbone molecules and polymers. With the results, we provide wide guidance for identifying the application of the current organic n-type doping technology in organic electronics.
|
|
5. |
- Bao, Qinye, et al.
(author)
-
Energy Level Bending in Ultrathin Polymer Layers Obtained through Langmuir-Shafer Deposition
- 2016
-
In: Advanced Functional Materials. - : WILEY-V C H VERLAG GMBH. - 1616-301X .- 1616-3028. ; 26:7, s. 1077-1084
-
Journal article (peer-reviewed)abstract
- The semiconductor-electrode interface impacts the function and the performance of (opto) electronic devices. For printed organic electronics the electrode surface is not atomically clean leading to weakly interacting interfaces. As a result, solution-processed organic ultrathin films on electrodes typically form islands due to dewetting. It has therefore been utterly difficult to achieve homogenous ultrathin conjugated polymer films. This has made the investigation of the correct energetics of the conjugated polymer-electrode interface impossible. Also, this has hampered the development of devices including ultrathin conjugated polymer layers. Here, LangmuirShafer-manufactured homogenous mono-and multilayers of semiconducting polymers on metal electrodes are reported and the energy level bending using photoelectron spectroscopy is tracked. The amorphous films display an abrupt energy level bending that does not extend beyond the first monolayer. These findings provide new insights of the energetics of the polymer-electrode interface and opens up for new high-performing devices based on ultrathin semiconducting polymers.
|
|
6. |
- Bao, Qinye, 1985-
(author)
-
Interface Phenomena in Organic Electronics
- 2015
-
Doctoral thesis (other academic/artistic)abstract
- Organic electronics based on organic semiconductors offer tremendous advantages compared to traditional inorganic counterparts such as low temperature processing, light weight, low manufacturing cost, high throughput and mechanical flexibility. Many key electronic processes in organic electronic devices, e.g. charge injection/extraction, charge recombination and exciton dissociation, occur at interfaces, significantly controlling performance and function. Understanding/modeling the interface energetics at organic-electrode/organic-organic heterojunctions is one of the crucial issues for organic electronic technologies to provide a route for improving device efficiency, which is the aim of the research presented in this thesis.Integer charge transfer (ICT) states pre-existed in the dark and created as a consequence of Fermi level equilibrium at donor-acceptor interface have a profound effect on open circuit voltage in organic bulk heterojunction photovoltaics. ICT state formation causes vacuum level misalignment that yields a roughly constant effective donor ionization potential to acceptor electron affinity energy difference at the donor-acceptor interface, even though there is a large variation in electron affinity for the fullerene series. The large variation in open circuit voltage for the corresponding device series instead is found to be a consequence of trap-assisted recombination via integer charge transfer states. Based on the results, novel design rules for optimizing open circuit voltage and performance of organic bulk heterojunction solar cells are proposed.Doping and insertion of interlayer are two established methods for enhancing charge injection/extraction properties at organic-electrode interface. By studying the energy level alignment behavior at low to intermediate doping levels for molecule-doped conjugated polymer/electrode interfaces, we deduce that two combined processes govern the interface energetics: (i) equilibration of the Fermi level due to oxidation (or reduction) of polymer sites at the interface as per the ICT model and (ii) a double dipole step induced by image charge from the dopant-polymer charge transfer complex that causes a shift of the work function. Such behavior is expected to hold in general for low to intermediate level doped organic semiconductor systems. The unified model is further extended to be suitable for conjugated electrolyte/electrode interfaces, revealing the design rules for achieving the smallest charge injection/extraction barrier for both thin tunneling and thick charge transporting conjugated electrolyte interlayers.To probe into the energy level spatial extension at interfaces, we employ the original approach of building and characterizing multilayers composed of a well-defined number of polymer monolayers with the Langmuir-Shäfer method to control polymer film uniformity and thicknesses, avoiding the problems associated with spin-coating ultrathin films. The disordered/amorphous films feature smaller, and in fact negligible, energy level bending compared to the more well-ordered films, in contradiction with existing models. It is found that that energy level bending depends on the ICT state distribution rather than the density of states of the neutral polymer chains in relation to the Fermi energy, thus taking into account the Coulomb energy associated with charging the polymer chain and transferring a charge across the interface. Based on this work, a general model for energy level bending in absence of significant doping of conjugated polymer films is proposed.Organic semiconductors are sensitive to ambient atmosphere that can influence the energetics. The degradation effects of common PCBM film induced by oxygen and water are found to be completely different. Upon exposure to oxygen, the work function is down-shifted by ~ 0.15 eV compared to the ICT curve of the pristine PCBM film, originating from the weak interaction between the fullerene part of PCBM and oxygen, and this can be reversed by thermal treatment in vacuum. The down-shift in energetics will cause a loss in open circuit voltage at electrode interface, but aids free charge generation at donor-acceptor interface. Upon exposure to water, there is irreversible extensive broadening and bleaching of the valence electronic structure features as well as a substantial decrease of work function and ionization potential, severely degrading the transport properties.Overall, the research results in this thesis thus give a deeper understanding of interface phenomena in organic electronics, especially regard to organic solar cells, aimed to further improve the device operation efficiency and lifetime.
|
|
7. |
- Bao, Qinye, et al.
(author)
-
Interfaces of (Ultra)thin Polymer Films in Organic Electronics
- 2019
-
In: Advanced Materials Interfaces. - : WILEY. - 2196-7350. ; 6:1
-
Research review (peer-reviewed)abstract
- In this short review the energy level alignment of interfaces involving solution-processed conjugated polymer (and soluble small molecules) films is described. Some general material properties of conjugated polymers and their solution-processed films are introduced, and the basic physics involved in energy level alignment at their interfaces is then discussed. An overview of energy level bending in (ultra)thin conjugated polymer films (often referred to as "band bending") is given and the effects of ion-containing interlayers typically used in organic electronic devices such as polymer light emitting diodes and organic bulk heterojunction solar cells are explored. The review finishes by describing a few of the available computational models useful for predicting and/or modeling energy level alignment at interfaces of solution-processed polymer films and discusses their respective strengths and weaknesses.
|
|
8. |
- Bao, Qinye, et al.
(author)
-
Oxygen- and Water-Based Degradation in [6,6]-Phenyl-C-61-Butyric Acid Methyl Ester (PCBM) Films
- 2014
-
In: Advanced Energy Materials. - : Wiley-VCH Verlag. - 1614-6832 .- 1614-6840. ; 4:6
-
Journal article (peer-reviewed)abstract
- Effects of in situ oxygen/water exposure on the energetics of [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) films are presented. For oxygen exposure, the work function is downshifted by ≈0.15 eV compared to the ideal integer charge transfer (ICT) curve for pristine PCBM, which is incompatible with significant introduction of electron trap states or p-doping. Water induces the highest occupied molecular orbital (HOMO) structure to undergo strong, irreversible modifications accompanied by a chemical interaction with PCBM.
|
|
9. |
- Bao, Qinye, et al.
(author)
-
Regular Energetics at Conjugated Electrolyte/Electrode Modifier for Organic Electronics and Their Implications of Design Rules
- 2015
-
In: Advanced Materials Interfaces. - : John Wiley & Sons. - 2196-7350. ; 2:12, s. 1-6
-
Journal article (peer-reviewed)abstract
- Regular energetics at a conjugated electrolyte/electrode modifier are found and controlled by equilibration of the Fermi level and an additional interface double dipole step induced by ionic functionality. Based on the results, design rules for conjugated electrolyte/electrode modifiers to achieve the smallest charge injection/exaction barrier and break through the current thickness limitation are proposed.
|
|
10. |
- Bao, Qinye, et al.
(author)
-
The Effect of Oxygen Uptake on Charge Injection Barriers in Conjugated Polymer Films
- 2018
-
In: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 10:7, s. 6491-6497
-
Journal article (peer-reviewed)abstract
- The energy offset between the electrode Fermi level and organic semiconductor transport levels is a key parameter controlling the charge injection barrier and hence efficiency of organic electronic devices. Here, we systematically explore the effect of in situ oxygen exposure on energetics in n-type conjugated polymer P(NDI2OD-T2) films. The analysis reveals that an interfacial potential step is introduced for a series of P(NDI2OD-T2) electrode contacts, causing a nearly constant downshift of the vacuum level, while the ionization energies versus vacuum level remain constant. These findings are attributed to the establishment of a so-called double-dipole step via motion of charged molecules and will modify the charge injection barriers at electrode contact. We further demonstrate that the same behavior occurs when oxygen interacts with p-type polymer TQ1 films, indicating it is possible to be a universal effect for organic semiconductOrs.
|
|
11. |
- Bao, Qinye, et al.
(author)
-
The energetics of the semiconducting polymer-electrode interface for solution-processed electronics
-
Other publication (other academic/artistic)abstract
- The semiconductor-electrode interface impacts the function and the performance of (opto-)electronic devices. For printed organic electronics the electrode surface is not atomically clean leading to weakly interacting interfaces. As a result, solution-processed organic ultra-thin films on electrodes typically form islands due to de-wetting. It has therefore been utterly difficult to achieve homogenous ultrathin conjugated polymer films. This has made the investigation of the correct energetics of the conjugated polymer-electrode interface impossible. Also, this has hampered the development of devices including ultra-thin conjugated polymer layers. Here, we report Langmuir-Shäfer-manufactured homogenous mono- and multilayers of semiconducting polymers on metal electrodes and track the energy level bending using photoelectron spectroscopy. The amorphous films display an abrupt energy level bending that does not extend beyond the first monolayer. Our findings provide new insights of the energetics of the polymer-electrode interface and opens up for new high-performing devices based on ultra-thin semiconducting polymers.
|
|
12. |
- Bao, Qinye, et al.
(author)
-
Trap-Assisted Recombination via Integer Charge Transfer States in Organic Bulk Heterojunction Photovoltaics
- 2014
-
In: Advanced Functional Materials. - : Wiley-VCH Verlag. - 1616-301X .- 1616-3028. ; 24:40, s. 6309-6316
-
Journal article (peer-reviewed)abstract
- Organic photovoltaics are under intense development and significant focus has been placed on tuning the donor ionization potential and acceptor electron affinity to optimize open circuit voltage. Here, it is shown that for a series of regioregular-poly(3-hexylthiophene): fullerene bulk heterojunction (BHJ) organic photovoltaic devices with pinned electrodes, integer charge transfer states present in the dark and created as a consequence of Fermi level equilibrium at BHJ have a profound effect on open circuit voltage. The integer charge transfer state formation causes vacuum level misalignment that yields a roughly constant effective donor ionization potential to acceptor electron affinity energy difference at the donor-acceptor interface, even though there is a large variation in electron affinity for the fullerene series. The large variation in open circuit voltage for the corresponding device series instead is found to be a consequence of trap-assisted recombination via integer charge transfer states. Based on the results, novel design rules for optimizing open circuit voltage and performance of organic bulk heterojunction solar cells are proposed.
|
|
13. |
- Ben Dkhil, Sadok, et al.
(author)
-
Interplay of Optical, Morphological, and Electronic Effects of ZnO Optical Spacers in Highly Efficient Polymer Solar Cells
- 2014
-
In: Advanced Energy Materials. - : Wiley-VCH Verlag. - 1614-6832 .- 1614-6840. ; 4:18, s. 1400805-
-
Journal article (peer-reviewed)abstract
- Optical spacers based on metal oxide layers have been intensively studied in poly(3-hexylthiophene) (P3HT) based polymer solar cells for optimizing light distribution inside the device, but to date, the potential of such a metal oxide spacer to improve the electronic performance of the polymer solar cells simultaneously has not yet be investigated. Here, a detailed study of performance improvement in high efficient polymer solar cells by insertion of solution-processed ZnO optical spacer using ethanolamine surface modification is reported. Insertion of the modified ZnO optical spacer strongly improves the performance of polymer solar cells even in the absence of an increase in light absorption. The electric improvements of the device are related to improved electron extraction, reduced contact barrier, and reduced recombination at the cathode. Importantly, it is shown for the first time that the morphology of optical spacer layer is a crucial parameter to obtain highly efficient solar cells in normal device structures. By optimizing optical spacer effects, contact resistance, and morphology of ZnO optical spacers, poly[[4,8-bis[(2-ethylhexyl) oxy] benzo[1,2-b: 4,5-b] dithiophene-2,6diyl] [3-fluoro-2-[(2-ethylhexyl) carbonyl] thieno[3,4-b] thiophenediyl]] (PTB7):[6,6]-phenyl-C71-butyric acid (PC70 BM) bulk heterojunction solar cells with conversion efficiency of 7.6% are obtained in normal device structures with all-solution-processed interlayers.
|
|
14. |
- Cai, Wanzhu, et al.
(author)
-
Self-doped conjugated polyelectrolyte with tuneable work function for effective hole transport in polymer solar cells
- 2016
-
In: Journal of Materials Chemistry A. - : Royal Society of Chemistry. - 2050-7488 .- 2050-7496. ; 4:40, s. 15670-15675
-
Journal article (peer-reviewed)abstract
- A water-soluble conjugated polyelectrolyte (CPE), PEDOT-S (poly(4-(2,3-dihydrothieno[3,4-b][1,4]dioxin-2-yl-methoxy)-1-butanesulfonic acid)), is demonstrated to be an excellent hole transport material in several polymer solar cells with different donor's HOMO (highest occupied molecular orbital). With a P3TI:PC71BM (poly[6,6′-bis(5′-bromo-3,4′-dioctyl-[2,2′-bithiophen]-5-yl)-1,1′-bis(2-hexyldecyl)-[3,3′-biindolinylidene]-2,2′-dione]:[6,6]-phenyl C71 butyric acid methyl ester) active layer, the device using PEDOT-S as a hole transport layer (HTL) outperforms the PEDOT:PSS-based devices due to an increased FF (fill factor). The devices' current density–voltage characteristics (J–V) show that a PEDOT-S layer can operate well with a wide range of thicknesses as well, helped by its high conductivity and decent transparency. With UV-ozone treatment, the work function of the PEDOT-S can increase from 4.9 eV to 5.2 eV. In TQ1:PC71BM (poly[[2,3-bis(3-octyloxyphenyl)-5,8-quinoxalinediyl]-2,5-thiophenediyl]:PC71BM) devices, which have a deeper donor HOMO than P3TI, Voc is improved from 0.81 V to 0.92 V by 7 min UV-ozone treatment, along with a suppressed reverse injection current and increased Jsc (short-circuit current density) and FF. Topography study shows the excellent coating ability of PEDOT-S. Conductive atomic force microscopy (C-AFM) shows the out-of-plane current in PEDOT-S film is one thousand times higher than that in PEDOT:PSS PH 4083 film under the same electric field and has much more uniformly distributed current pathways.
|
|
15. |
- Cai, Yunhao, et al.
(author)
-
Effect of the Energy Offset on the Charge Dynamics in Nonfullerene Organic Solar Cells
- 2020
-
In: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 12:39, s. 43984-43991
-
Journal article (peer-reviewed)abstract
- The energy offset, considered as the driving force for charge transfer between organic molecules, has significant effects on both charge separation and charge recombination in organic solar cells. Herein, we designed material systems with gradually shifting energy offsets, including both positive and negative values. Time-resolved spectroscopy was used to monitor the charge dynamics within the bulk heterojunction. It is striking to find that there is still charge transfer and charge generation when the energy offset reached -0.10 eV (ultraviolet photoelectron spectroscopy data). This work not only indicates the feasibility of the free carrier generation and the following charge separation under the condition of a negative offset but also elucidates the relationship between the charge transfer and the energy offset in the case of polymer chlorination.
|
|
16. |
- Guo, Xuewen, et al.
(author)
-
Novel small-molecule zwitterionic electrolyte with ultralow work function as cathode modifier for inverted polymer solar cells
- 2018
-
In: Organic electronics. - : ELSEVIER SCIENCE BV. - 1566-1199 .- 1878-5530. ; 59, s. 15-20
-
Journal article (peer-reviewed)abstract
- Interfacial compatibility between the electrode and organic semiconductor plays a critical role in controlling the charge transport and hence efficiency of organic solar cell. Here, we introduce a novel small-molecule zwitterionic electrolyte (S1) combined with ZnO as electron transporting interlayer employed for the inverted PTB7:PC71BM bulk heterojunction solar cell. The resulting device with the S1/ZnO stacked interlayer achieves a high PCE of 8.59%, obtaining a 16.2% improvement over the control device performance of 7.4% without the S1 attributed to the significant increased short-circuit current density and fill factor. The interfacial properties are investigated. It is found that the S1/ZnO interlayer possess an ultralow work function of 3.6 eV, which originates from the interfacial double dipole step induced by the zwitterionic side chain electrostatic realignment at interface. The S1/ZnO interlayer exhibits the excellent charge extraction ability, suppresses the charge recombination loss and decreases the series resistance at the active layer/electrode contact.
|
|
17. |
- Guo, Xuewen, et al.
(author)
-
Understanding the effect of N2200 on performance of J71 : ITIC bulk heterojunction in ternary non-fullerene solar cells
- 2019
-
In: Organic electronics. - : Elsevier. - 1566-1199 .- 1878-5530. ; 71, s. 65-71
-
Journal article (peer-reviewed)abstract
- None-fullerene solar cells with ternary architecture have attracted much attention because it is an effective approach for boosting the device power conversion efficiency. Here, the crystalline polymer N2200 as the third component is integrated into J71: ITIC bulk heterojunction. A series of characterizations indicate that N2200 could increase photo-harvesting, balanced hole and electron mobilities, enhanced exciton dissociation, and suppressed charge recombination, which result in the comprehensive improvement of open circuit voltage, short circuit current and fill factor in the device. Moreover, after introduction of N2200, the morphology of the ternary active layer is optimized, and the film crystallinity is improved. This work demonstrates that adding a small quantity of high crystallization acceptor into non-fullerene donor: acceptor mixture is a promising strategy toward developing high-performance organic solar cells.
|
|
18. |
- Jiang, Sheng, et al.
(author)
-
Constructing Chromium Multioxide Hole-Selective Heterojunction for High-Performance Perovskite Solar Cells
- 2022
-
In: Advanced Science. - : Wiley. - 2198-3844. ; 9:30
-
Journal article (peer-reviewed)abstract
- Perovskite solar cells (PSCs) suffer from significant nonradiative recombination at perovskite/charge transport layer heterojunction, seriously limiting their power conversion efficiencies. Herein, solution-processed chromium multioxide (CrOx) is judiciously selected to construct a MAPbI(3)/CrOx/Spiro-OMeTAD hole-selective heterojunction. It is demonstrated that the inserted CrOx not only effectively reduces defect sites via redox shuttle at perovskite contact, but also decreases valence band maximum (VBM)-HOMO offset between perovskite and Spiro-OMeTAD. This will diminish thermionic losses for collecting holes and thus promote charge transport across the heterojunction, suppressing both defect-assisted recombination and interface carrier recombination. As a result, a remarkable improvement of 21.21% efficiency with excellent device stability is achieved compared to 18.46% of the control device, which is among the highest efficiencies for polycrystalline MAPbI(3) based n-i-p planar PSCs reported to date. These findings of this work provide new insights into novel charge-selective heterojunctions for further enhancing efficiency and stability of PSCs.
|
|
19. |
- Jiang, Sheng, et al.
(author)
-
In Situ Reconstruction of Hole-Selective Perovskite Heterojunction with Graded Energetics Toward Highly Efficient and Stable Solar Cells
- 2023
-
In: Advanced Energy Materials. - : WILEY-V C H VERLAG GMBH. - 1614-6832 .- 1614-6840. ; 13:27
-
Journal article (peer-reviewed)abstract
- Perovskite solar cells (PSCs) have demonstrated a high power conversion efficiency, however, the large energy loss due to non-radiative recombination is the main challenge for further performance enhancement. Here, a surface treatment strategy is developed by heat-induced decomposition of a thin interlayer 2,7-Naphthaleneditriflate (NAP) to in situ reconstruct perovskite energetics. It is verified that the reconstructed perovskite surface energetics match better with the upper hole transport layer compared to the intrinsic condition. Spontaneous generation of n/n(-) homojunctions between the perovskite film bulk and the surface region promotes hole extraction, enhancing built-in electric field, and thus significantly suppresses charge recombination at such perovskite hole-selective heterojunctions. Moreover, the surface decomposed fluorine-rich complexes passivate the defects and improve the crystallinity of the perovskite film. These advantages are confirmed by a remarkably improved efficiency from 20.52% for the control device to 23.37% for the treated one with excellent stability. The work provides a promising approach of in situ reconstructing perovskite surface and interface for the design of highly efficient and stable PSCs.
|
|
20. |
- Li, Danqin, et al.
(author)
-
Enhanced and Balanced Charge Transport Boosting Ternary Solar Cells Over 17% Efficiency
- 2020
-
In: Advanced Materials. - : WILEY-V C H VERLAG GMBH. - 0935-9648 .- 1521-4095. ; 32:34
-
Journal article (peer-reviewed)abstract
- Ternary architecture is one of the most effective strategies to boost the power conversion efficiency (PCE) of organic solar cells (OSCs). Here, an OSC with a ternary architecture featuring a highly crystalline molecular donor DRTB-T-C4 as a third component to the host binary system consisting of a polymer donor PM6 and a nonfullerene acceptor Y6 is reported. The third component is used to achieve enhanced and balanced charge transport, contributing to an improved fill factor (FF) of 0.813 and yielding an impressive PCE of 17.13%. The heterojunctions are designed using so-called pinning energies to promote exciton separation and reduce recombination loss. In addition, the preferential location of DRTB-T-C4 at the interface between PM6 and Y6 plays an important role in optimizing the morphology of the active layer.
|
|
21. |
|
|
22. |
- Li, Danqin, et al.
(author)
-
n-Doping of photoactive layer in binary organic solar cells realizes over 18.3% efficiency
- 2022
-
In: Nano Energy. - : ELSEVIER. - 2211-2855 .- 2211-3282. ; 96
-
Journal article (peer-reviewed)abstract
- Electronic doping of conjugated semiconductor plays a critical role in the fabrication of high efficiency organic optoelectronic devices. Here, we report an organic solar cell (OSC) by doping n-type DMBI-BDZC into one host binary bulk heterojunction (BHJ) photoactive layer comprised of a polymer donor PM6 and a nonfullerene acceptor Y6. The resulting champion device yields a significantly improved power conversion efficiency from 17.17% to 18.33% with an impressive fill factor of 80.20%. It is found that the electrically doped photoactive layer exhibits enhanced and balanced charge carrier mobilities, more effective exciton dissociation, longer carrier lifetime, and suppressed charge recombination with smaller energy loss. The dopant molecule DMBIBDZC also act as a surface morphology modifier of the photoactive layer with enhanced charge transport. This work demonstrates that manipulation of charge transport via adding a low concentration dopant into photoactive layer is a promising approach for further improvement of BHJ OSC performance.
|
|
23. |
- Phelipot, Jonathan, et al.
(author)
-
Highly Emissive Layers based on Organic/Inorganic Nanohybrids Using Aggregation Induced Emission Effect
- 2022
-
In: Advanced Materials Technologies. - : WILEY. - 2365-709X. ; 7:1
-
Journal article (peer-reviewed)abstract
- Fluorescent nanohybrids, based on pi-extended hydroxyoxophosphole ligands grafted onto ZnO nanoparticles, are designed and studied. The restriction of the intramolecular motions of the organic fluorophore, through either aggregates formation in solution or processing into thin films, forms highly emissive materials due to a strong aggregation induced emission effect. Theoretical calculations and XPS analyses were performed to analyze the interactions between the organic and inorganic counterparts. Preliminary results on the use of these nanohybrids as solution-processed emissive layers in organic light emitting diodes (OLEDs) illustrate their potential for lighting applications.
|
|
24. |
|
|
25. |
- Sun, Zhengyi, et al.
(author)
-
Role of Thick-Lithium Fluoride Layer in Energy Level Alignment at Organic/Metal Interface: Unifying Effect on High Metallic Work Functions
- 2015
-
In: ADVANCED MATERIALS INTERFACES. - : Wiley: 12 months. - 2196-7350. ; 2:4, s. 1400527-
-
Journal article (peer-reviewed)abstract
- The function of approximate to 3-nm thick lithium fluoride (LiF) buffer layers in combination with high work function metal contacts such as coinage metals and ferromagnetic metals for use in organic electronics and spintronics is investigated. The energy level alignment at the organic/LiF/metal interface is systematically studied using photoelectron spectroscopy and the integer charge transfer model. The thick-LiF buffer layer is found to pin the Fermi level to approximate to 3.8 eV, regardless of the work function of the initial metal due to energy level bending in the LiF layer caused by depletion of defect states. At 3-nm thickness, the LiF buffer layer provides full coverage, and the organic semiconductor adlayers are found to physisorb with the consequence that the energy level alignment at the organic/LiF interface follows the integer charge transfer models predictions.
|
|
26. |
|
|
27. |
- Tang, Zheng, et al.
(author)
-
Fully-solution-processed organic solar cells with a highly efficient paper-based light trapping element
- 2015
-
In: Journal of Materials Chemistry A. - : ROYAL SOC CHEMISTRY. - 2050-7488 .- 2050-7496. ; 3:48, s. 24289-24296
-
Journal article (peer-reviewed)abstract
- We demonstrate the use of low cost paper as an efficient light-trapping element for thin film photovoltaics. We verify its use in fully-solution processed organic photovoltaic devices with the highest power conversion efficiency and the lowest internal electrical losses reported so far, the architecture of which - unlike most of the studied geometries to date - is suitable for upscaling, i.e. commercialization. The use of the paper-reflector enhances the external quantum efficiency (EQE) of the organic photovoltaic device by a factor of approximate to 1.5-2.5 over the solar spectrum, which rivals the light harvesting efficiency of a highly-reflective but also considerably more expensive silver mirror back-reflector. Moreover, by detailed theoretical and experimental analysis, we show that further improvements in the photovoltaic performance of organic solar cells employing PEDOT:PSS as both electrodes rely on the future development of high-conductivity and high-transmittance PEDOT:PSS. This is due optical losses in the PEDOT:PSS electrodes.
|
|
28. |
- Tang, Zheng, et al.
(author)
-
Improving Cathodes with a Polymer Interlayer in Reversed Organic Solar Cells
- 2014
-
In: Advanced Energy Materials. - : Wiley-VCH Verlagsgesellschaft. - 1614-6832 .- 1614-6840. ; 4:15
-
Journal article (peer-reviewed)abstract
- The effects of cathode modification by a conjugated polymer interlayer PFPA1 on the performance of reversed organic solar cells (substrate/cathode/active layer/transparent anode) based on different active material systems and different substrate electrodes are systematically investigated. A reduction of the work function irrespective of the substrate cathode used is observed upon the deposition of the PFPA1 interlayer, which is further related to an improved built-in electric field and open-circuit voltage. The amphiphilic character of the PFPA1 interlayer alters the surface energy of the substrate cathode, leading to the formation of a better active layer morphology aiding efficient exciton dissociation and photocurrent extraction in the modified solar cells. Hence, internal quantum efficiency is found to be significantly higher than that of their unmodified counterparts, while optically, the modified and unmodified solar cells are identical. Moreover, the deep highest occupied molecular orbital (HOMO) of the PFPA1 interlayer improves the selectivity for all investigated substrate cathodes, thus enhancing the fill factor.
|
|
29. |
- Tang, Zheng, et al.
(author)
-
Universal modification of poor cathodes into good ones by a polymer interlayer for high performance reversed organic solar cells
- 2014
-
Other publication (other academic/artistic)abstract
- In organic bulk-heterojunction solar cells, energy losses at the active layer/electrode interface are often observed. Modification of these interfaces with organic interlayers optimizes charge carrier injection and extraction and thus improves device performance. In this work, the effects of cathode modification by a conjugated polymer interlayer PFPA1 on the performance of reversed organic solar cells (substrate/cathode/active layer/transparent anode) based on different active material systems and different substrate electrodes are systematically investigated. A reduction of the work function irrespective of the substrate cathode used is observed upon the deposition of the PFPA1 interlayer; further related to an improved built-in electric field and open-circuit voltage. The amphiphilic character of the PFPA1 interlayer alters the surface energy of the substrate cathode, leading to the formation of a better active layer morphology aiding efficient exciton dissociation and photocurrent extraction in the modified solar cells. Hence, internal quantum efficiency is found significantly higher than that of their unmodified counterparts, while optically, the modified and unmodified solar cells are identical. Moreover, the deep HOMO of the PFPA1 interlayer improves the selectivity for all investigated substrate cathodes, thus enhancing the fill factor. We demonstrate a possibility of improving photovoltaic performance of reversed solar cells via a simple and universal interface modification and provide the basic guidelines for development and characterization of interface materials for organic solar cells in general.
|
|
30. |
- Wang, Chuanfei, et al.
(author)
-
Organic Semiconductor Interfaces and Their Effects in Organic Solar Cells
- 2023
-
In: Chinese journal of chemistry. - : WILEY-V C H VERLAG GMBH. - 1001-604X .- 1614-7065.
-
Research review (peer-reviewed)abstract
- Energy levels and energy level alignment at interfaces play a decisive role in designing efficient and stable organic solar cells (OSCs). In this review two usually used technologies in organic photovoltaic communities for measuring energy levels of organic semiconductors, photoelectron spectroscopy and electrochemical methods, are introduced, and the relationships between the values obtained from the corresponding techniques are compared. The energy level and energy level alignment across the interfaces involved in solution processed organic photovoltaics are described, and the corresponding integer charge transfer model for predicting and explaining energy level alignment is presented. The effects of the interface properties in designing efficient binary and ternary OSCs were discussed. The effects of environmental factors mainly including water vapor, oxygen gas and thermal annealing on energy levels and energy level alignment involved in photoactive layers, and the subsequent effects on the corresponding OSC properties are given.
|
|
31. |
- Xiao, Wei, et al.
(author)
-
Exploring Red, Green, and Blue Light-Activated Degradation of Perovskite Films and Solar Cells for Near Space Applications
- 2020
-
In: Solar RRL. - : Wiley-VCH Verlagsgesellschaft. - 2367-198X. ; 4:3
-
Journal article (peer-reviewed)abstract
- Hybrid perovskite solar cells with a high specific power have great potential to become promising power sources mounted on spacecrafts in space applications. However, there is a lack of study on their photostability as light absorbers in those conditions. Herein, the stability of the perovskite films and solar cells under red, green, and blue (RGB) light illumination in medium vacuum that belongs to near space is explored. The perovskite active layers exhibit different degradations from morphological, chemical, and structural points of view. This is attributed to the strong coupling between photoexcited carriers and the crystal lattice and the diversity of RGB light absorption in the perovskite films. Device characterizations reveal that the efficiency loss of perovskite solar cells results from not only perovskite degradation, but also the photoexcited carriers reducing the energy barrier of ion migration and accelerating the migration to generate more deep-level trap defects. Moreover, comparative devices suggest that the well encapsulation can weaken the effect of vacuum on stability.
|
|
32. |
- Xiong, Shaobing, et al.
(author)
-
Additive-Induced Synergies of Defect Passivation and Energetic Modification toward Highly Efficient Perovskite Solar Cells
- 2021
-
In: Advanced Energy Materials. - : WILEY-V C H VERLAG GMBH. - 1614-6832 .- 1614-6840. ; 11:29
-
Journal article (peer-reviewed)abstract
- Defect passivation via additive and energetic modification via interface engineering are two effective strategies for achieving high-performance perovskite solar cells (PSCs). Here, the synergies of pentafluorophenyl acrylate when used as additive, in which it not only passivates surface defect states but also simultaneously modifies the energetics at the perovskite/Spiro-OMeTAD interface to promote charge transport, are shown. The additive-induced synergy effect significantly suppresses both defect-assisted recombination and interface carrier recombination, resulting in a device efficiency of 22.42% and an open-circuit voltage of 1.193 V with excellent device stability. The two photovoltaic parameters are among the highest values for polycrystalline CsFormamidinium/Methylammonium (FAMA)/FAMA based n-i-p structural PSCs using low-cost silver electrodes reported to date. The findings provide a promising approach by choosing the dual functional additive to enhance efficiency and stability of PSCs.
|
|
33. |
- Xiong, Shaobing, et al.
(author)
-
Defect passivation by nontoxic biomaterial yields 21% efficiency perovskite solar cells
- 2021
-
In: Journal of Energy Challenges and Mechanics. - : ELSEVIER. - 2056-9386. ; 55, s. 265-271
-
Journal article (peer-reviewed)abstract
- Defect passivation is one of the most important strategies to boost both the efficiency and stability of perovskite solar cells (PSCs). Here, nontoxic and sustainable forest-based biomaterial, betulin, is first introduced into perovskites. The experiments and calculations reveal that betulin can effectively passivate the uncoordinated lead ions in perovskites via sharing the lone pair electrons of hydroxyl group, promoting charge transport. As a result, the power conversion efficiencies of the p-i-n planar PSCs remarkably increase from 19.14% to 21.15%, with the improvement of other parameters. The hydrogen bonds of betulin lock methylamine and halogen ions along the grain boundaries and on the film surface and thus suppress ion migration, further stabilizing perovskite crystal structures. These positive effects enable the PSCs to maintain 90% of the initial efficiency after 30 days in ambient air with 60%+/- 5% relative humidity, 75% after 300 h aging at 85 degrees C, and 55% after 250 h light soaking, respectively. This work opens a new pathway for using nontoxic and low-cost biomaterials from forest to make highly efficient and stable PSCs. (C) 2020 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by ELSEVIER B.V. and Science Press. All rights reserved.
|
|
34. |
- Xiong, Shaobing, et al.
(author)
-
Defect-Passivation Using Organic Dyes for Enhanced Efficiency and Stability of Perovskite Solar Cells
- 2020
-
In: Solar RRL. - : WILEY-V C H VERLAG GMBH. - 2367-198X. ; 4:5
-
Journal article (peer-reviewed)abstract
- Perovskite solar cells are a highly competitive candidate for next-generation photovoltaic technology. Defects in the perovskite grain boundaries and on the film surfaces however have significant impacts on both the device efficiency and environmental stability. Herein, a strategy using organic dyes as additives to passivate the defect states and produce more n-type perovskite films, thereby improving charge transport and decreasing charge recombination, is reported. Based on this strategy, the power conversion efficiency of the perovskite solar cell is significantly increased from 18.13% to 20.18% with a negligible hysteresis. Furthermore, the rich hydrogen bonds and carbonyl structures in the organic dye can significantly enhance device stability both in terms of humidity and thermal stress. The results present a promising pathway using abundant and colorful organic dyes as additives to achieve high-performance perovskite solar cells.
|
|
35. |
- Xiong, Shaobing, et al.
(author)
-
Direct Observation on p- to n-Type Transformation of Perovskite Surface Region during Defect Passivation Driving High Photovoltaic Efficiency
- 2021
-
In: Joule. - : CELL PRESS. - 2542-4351. ; 5:2, s. 467-480
-
Journal article (peer-reviewed)abstract
- Perovskite solar cells (PSCs) suffer from significant nonradiative recombination, limiting their power conversion efficiencies. Here, for the first time, we directly observe a complete transformation of perovskite MAPbI(3) surface region energetics from p- to n-type during defect passivation caused by natural additive capsaicin, attributed to the spontaneous formation of a p-n homojunction in perovskite active layer. We demonstrate that the p-n homojunction locates at similar to 100 nm below perovskite surface. The energetics transformation and defect passivation promote charge transport in bulk perovskite layer and at perovskite/PCBM interface, suppressing both defect-assisted recombination and interface carrier recombination. As a result, an efficiency of 21.88% and a fill factor of 83.81% with excellent device stability are achieved, both values are the highest records for polycrystalline MAPbI(3) based p-i-n PSCs reported to date. The proposed new concept of synergetic defect passivation and energetic modification via additive provides a huge potential for further improvement of PSC performance.
|
|
36. |
- Xiong, Shaobing, et al.
(author)
-
Engineering of the Back Contact between PCBM and Metal Electrode for Planar Perovskite Solar Cells with Enhanced Efficiency and Stability
- 2019
-
In: Advanced Optical Materials. - : WILEY-V C H VERLAG GMBH. - 2162-7568 .- 2195-1071. ; 7:19
-
Journal article (peer-reviewed)abstract
- The cathode interface plays a critical role in achieving high-performance fullerene/perovskite planar solar cells. Herein, the simple molecule Isatin and its derivatives are introduced at the back contact [6,6]-phenyl-C61-butyric acid methyl ester (PCBM)/Al as a cathode modification interlayer. It is revealed that the Isatin interlayers facilitate electron transport/extraction and suppress electron recombination, attributed to the formation of negative dipole potential steps and the passivation of the interfacial trap density. The average power conversion efficiencies of the resulting devices are significantly improved by 11% from 17.68% to 19.74%, with an enhancement in all device parameters including short-circuit current, open-circuit voltage, and fill factor. The hysteresis index is found to disappear. In addition, such interlayer enhances device stability under ambient conditions compared to the control devices due to suppression of moisture-induced degradation of the perovskite films. These findings provide a comprehensive understanding of the engineering of the back contact between PCBM and the metal electrode to improve efficiency and stability of perovskite solar cells.
|
|
37. |
- Xiong, Shaobing, et al.
(author)
-
Reducing nonradiative recombination for highly efficient inverted perovskite solar cells via a synergistic bimolecular interface
- 2024
-
In: Nature Communications. - : NATURE PORTFOLIO. - 2041-1723. ; 15:1
-
Journal article (peer-reviewed)abstract
- Reducing interface nonradiative recombination is important for realizing highly efficient perovskite solar cells. In this work, we develop a synergistic bimolecular interlayer (SBI) strategy via 4-methoxyphenylphosphonic acid (MPA) and 2-phenylethylammonium iodide (PEAI) to functionalize the perovskite interface. MPA induces an in-situ chemical reaction at the perovskite surface via forming strong P-O-Pb covalent bonds that diminish the surface defect density and upshift the surface Fermi level. PEAI further creates an additional negative surface dipole so that a more n-type perovskite surface is constructed, which enhances electron extraction at the top interface. With this cooperative surface treatment, we greatly minimize interface nonradiative recombination through both enhanced defect passivation and improved energetics. The resulting p-i-n device achieves a stabilized power conversion efficiency of 25.53% and one of the smallest nonradiative recombination induced Voc loss of only 59 mV reported to date. We also obtain a certified efficiency of 25.05%. This work sheds light on the synergistic interface engineering for further improvement of perovskite solar cells. Reducing interface nonradiative recombination is important for realizing highly efficient perovskite solar cells. Here, the authors employ a bimolecular interlayer to functionalize the perovskite interface, achieving cooperative surface treatment and certified power conversion efficiency of 25.05%.
|
|
38. |
- Xiong, Shaobing, et al.
(author)
-
Revealing buried heterointerface energetics towards highly efficient perovskite solar cells
- 2023
-
In: Nano Energy. - : ELSEVIER. - 2211-2855 .- 2211-3282. ; 109
-
Journal article (peer-reviewed)abstract
- The heterointerfaces of charge-selective contacts are crucial in determining efficiency and stability of perovskite optoelectronic devices, where the fundamental knowledge of the buried heterointerface between perovskite and bottom charge transport layer is less well understood compared to the top interface. Herein, we systematically investigate the energetics at the perovskite/SnO2 buried heterointerface for an n-i-p perovskite solar cell (PSC) and the perovskite/PEDOT:PSS buried heterointerface for a p-i-n one, respectively. In contrast to previous cognitions, we discover a perovskite transition phase at the buried interface region that originates from the chemical bonding interaction with the bottom charge transport layer. The transition phase causes an energy level barrier and induces defects, impeding charge transport across the heterointerface. These detrimental effects trigger significant nonradiative recombination and limit the attainable device photovoltage. We then develop the energetic models that describe such buried heterointerfaces. Moreover, we further test the proposed model -derived mechanisms via inserting a thin polyvinyl alcohol layer into the buried heterointerfaces of the de-vices. We demonstrate that chemical interactions and formation of the perovskite transition phase at the buried heterointerface thereby are fully restrained, leading to a diminished electron extraction barrier and improved charge transport. As a result, significant increases in open-circuit voltage and fill factor of the devices are ach-ieved. These results will help guide future efforts on developing suitable buried heterointerfaces for superior performance of perovskite optoelectronics.
|
|
39. |
- Xiong, Shaobing, et al.
(author)
-
Surface charge-transfer doping for highly efficient perovskite solar cells
- 2021
-
In: Nano Energy. - : ELSEVIER. - 2211-2855 .- 2211-3282. ; 79
-
Journal article (peer-reviewed)abstract
- Nonradiative recombination losses are the predominant reason that limits the full thermodynamic potential of perovskite solar cells (PSCs), mainly originating from surface defects and interfacial energetics. However, their synergies between the two key factors are poorly understood. Herein, we systemically explore the energetic role of ionic liquid defect-passivator Tetrabutylammonium hexafluorophosphate (TBAPF(6)) on n-i-p planar PSCs. The perovskite film surface has been transformed from p-type to n-type after TBAPF(6) modification, evidenced by a shift of Fermi level closer to the conduction band. The n-type energetics result in a higher density of electron carrier and a smaller electron extraction barrier at perovskite/PCBM interface, promoting charge transport. It is also shown that the perovskite film can undergo a clear transformation from n-type to p-type character as increasing work function of substrates. Further studies clearly illustrate that TBAPF(6) not only reduces the surface defect-assisted recombination, but also restrains the interface carrier recombination. These combined effects lead to the effective suppression of nonradiative recombination, attributing to a significant improvement in the device power conversion efficiency.
|
|
40. |
- Yang, Jianming, et al.
(author)
-
Comprehensive understanding of heat-induced degradation of triple-cation mixed halide perovskite for a robust solar cell
- 2018
-
In: Nano Energy. - : ELSEVIER SCIENCE BV. - 2211-2855 .- 2211-3282. ; 54, s. 218-226
-
Journal article (peer-reviewed)abstract
- The triple-cation mixed halide perovskite Cs-0.05(MA(0.17)FA(0.83))(0.95)Pb(I0.83Br0.17)(3) emerges as one of the most promising candidates for photovoltaics due to superior optoelectronic properties, but the thermal stability is still a major challenge for the viability of perovskite solar cells towards commercialization. Herein, we firstly explore the thermal response of the photovoltaic performances to access device physical changes. It is shown that the efficiency loss originates from decreased charge mobility, increased trap density and generation of PbI2 charge recombination centers near the interface. In-depth analysis of evolutions in morphology, chemical composition, dynamic and electronic structure of the perovskite layer at the nanometer scales indicates that it is initial dangling bonds and vacancies on the imperfect surfaces decrease the activation energy and cause the perovskite decomposition in a layer-by-layer pathway sequentially from the film surface to bulk. Based on the results, a strategy of surface passivation to improve the thermal stability is demonstrated and discussed. This work for the first time provides insights into the physical and chemical change of such triple-cation perovskite and indicates that more effort should be invested in surface treatment for enhancing perovskite device stability.
|
|
41. |
- Yang, Jianming, et al.
(author)
-
Energetics and Energy Loss in 2D Ruddlesden-Popper Perovskite Solar Cells
- 2020
-
In: Advanced Energy Materials. - : WILEY-V C H VERLAG GMBH. - 1614-6832 .- 1614-6840. ; 10:23
-
Journal article (peer-reviewed)abstract
- 2D Ruddlesden-Popper perovskites (RPPs) are emerging as potential challengers to their 3D counterpart due to superior stability and competitive efficiency. However, the fundamental questions on energetics of the 2D RPPs are not well understood. Here, the energetics at (PEA)(2)(MA)(n)-1PbnI3n+1/[6,6]-phenyl-C61-butyric acid methyl ester (PCBM) interfaces with varying n values of 1, 3, 5, 40, and infinity are systematically investigated. It is found that n-n junctions form at the 2D RPP interfaces (n = 3, 5, and 40), instead of p-n junctions in the pure 2D and 3D scenarios (n = 1 and infinity). The potential gradient across phenethylammonium iodide ligands that significantly decreases surface work function, promotes separation of the photogenerated charge carriers with electron transferring from perovskite crystal to ligand at the interface, reducing charge recombination, which contributes to the smallest energy loss and the highest open-circuit voltage (V-oc) in the perovskite solar cells (PSCs) based on the 2D RPP (n = 5)/PCBM. The mechanism is further verified by inserting a thin 2D RPP capping layer between pure 3D perovskite and PCBM in PSCs, causing the V-oc to evidently increase by 94 mV. Capacitance-voltage measurements with Mott-Schottky analysis demonstrate that such V-oc improvement is attributed to the enhanced potential at the interface.
|
|
42. |
- Yang, Jianming, et al.
(author)
-
Extremely Low-Cost and Green Cellulose Passivating Perovskites for Stable and High-Performance Solar Cells
- 2019
-
In: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 11:14, s. 13491-13498
-
Journal article (peer-reviewed)abstract
- The fast evolution of metal halide perovskite solar cells has opened a new chapter in the field of renewable energy. High-quality perovskite films as the active layers are essential for both high efficiency and long-term stability. Here, the perovskite films with enlarged crystal grain size and decreased defect density are fabricated by introducing the extremely low-cost and green polymer, ethyl cellulose (EC), into the perovskite layer. The addition of EC triggers hydrogen bonding interactions between EC and the perovskite, passivating the charge defect traps at the grain boundaries. The long chain of EC further acts as a scaffold for the perovskite structure, eliminating the annealing-induced lattice strain during the film fabrication process. The resulting devices with the EC additive exhibit a remarkably enhanced average power conversion efficiency from 17.11 to 19.27% and an improvement of all device parameters. The hysteresis index is found to decrease by three times from 0.081 to 0.027, which is attributed to suppressed ion migration and surface charge trapping. In addition, the defect passivation by EC significantly improves the environmental stability of the perovskite films, yielding devices that retain 80% of their initial efficiency after 30 days in ambient air at 45% relative humidity, whereas the pristine devices without EC fully degrade. This work provides a low-cost and green avenue for passivating defects that improves both the efficiency and operational stability of perovskite solar cells.
|
|
43. |
- Yang, Jianming, et al.
(author)
-
Oxygen- and Water-Induced Energetics Degradation in Organometal Halide Perovskites
- 2018
-
In: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 10:18, s. 16225-16230
-
Journal article (peer-reviewed)abstract
- Organometal halide perovskites are under rapid development, and significant focus has been placed on their stability that currently presents a major obstacle for practical application. Energetics plays a vital role in charge injection/extraction and transport properties in devices. Here, we in situ investigate oxygen and water-induced energetics degradation in organometal halide perovskite films. Oxygen gas induces an upward shift of the vacuum level of the perovskite films because of the formation of an oxygen induced surface dipole, water vapor causes a significant vacuum-level downshift, and the valence band binding energy referenced to the Fermi level simultaneously increases so as to keep the ionization potential of the perovskite films unchanged. Moreover, the chemical compositions, crystalline structures, surface morphologies, and dynamical properties also are monitored and analyzed in detail. These results are indispensable to understand the degradation mechanisms and to perform the optimizations of stable materials and devices in the future.
|
|
44. |
- Yang, Jianming, et al.
(author)
-
Unraveling Photostability of Mixed Cation Perovskite Films in Extreme Environment
- 2018
-
In: Advanced Optical Materials. - : WILEY-V C H VERLAG GMBH. - 2162-7568 .- 2195-1071. ; 6:20
-
Journal article (peer-reviewed)abstract
- Organometal halide perovskites exhibit a bright future for applications in solar cells, as efficiency has achieved over 22%. The long-term stability remains a major obstacle for commercialization. Here, it is found that three cationic compositional engineered perovskites, MAPb(I0.83Br0.17)(3), FA(0.83)MA(0.17)Pb(I0.83Br0.17)(3), and Cs-0.1(FA(0.83)MA(0.17))(0.9)Pb(I0.83Br0.17)(3), undergo severe degradation under white-light illumination in ultrahigh vacuum (UHV) environment, but the rate of degradation is significantly lower for the mixed cation perovskites. This is attributed to the defect-induced trap states that trigger the strong coupling between the photoexcited carriers and the crystal lattice. The observed behavior supports the view of the mixed cations suppressing the photoinduced degradation. It is further demonstrated that UHV environment remarkably accelerates the degradation of the perovskite films under illumination, which delivers a very important message that the current hybrid perovskite materials and their optoelectronic devices are not suitable for application in outer space. Moreover, the applied UHV environment can be an accelerated test method to estimate the photostability of the perovskites.
|
|
45. |
- Zhang, Qilun, 1992-, et al.
(author)
-
Industrial Kraft Lignin Based Binary Cathode Interface Layer Enables Enhanced Stability in High Efficiency Organic Solar Cells
- 2023
-
In: Advanced Materials. - : WILEY-V C H VERLAG GMBH. - 0935-9648 .- 1521-4095.
-
Journal article (peer-reviewed)abstract
- Herein, a binary cathode interface layer (CIL) strategy based on the industrial solvent fractionated LignoBoost kraft lignin (KL) is adopted for fabrication of organic solar cells (OSCs). The uniformly distributed phenol moieties in KL enable it to easily form hydrogen bonds with commonly used CIL materials, i.e., bathocuproine (BCP) and PFN-Br, resulting in binary CILs with tunable work function (WF). This work shows that the binary CILs work well in OSCs with large KL ratio compatibility, exhibiting equivalent or even higher efficiency to the traditional CILs in state of art OSCs. In addition, the combination of KL and BCP significantly enhanced OSC stability, owing to KL blocking the reaction between BCP and nonfullerene acceptors (NFAs). This work provides a simple and effective way to achieve high-efficient OSCs with better stability and sustainability by using wood-based materials. This work introduces industrial solvent fractionated LignoBoost kraft lignin (KL) in highly efficient organic solar cells (OSCs) by binary cathode interface layer (CIL) strategy, which can significantly improve the stability of both binary and ternary photoactive layer (PAL) OSC, owing to the passivation of diffusion and reaction between bathocuproine (BCP) and nonfullerene acceptors (NFAs). The results combine sustainable wood-based material with classic interface materials in advance NFA-OSCs.image
|
|
46. |
- Zhang, Wenjun, et al.
(author)
-
Morphological Control for Highly Efficient Inverted Polymer Solar Cells Via the Backbone Design of Cathode Interlayer Materials
- 2014
-
In: Advanced Energy Materials. - : Wiley-VCH Verlag. - 1614-6832 .- 1614-6840. ; 4:12, s. 1400359-
-
Journal article (peer-reviewed)abstract
- Two alcohol-soluble organic molecules are synthesized and introduced into inverted organic solar cells as the cathode interlayer. A power conversion efficiency as high as 9.22% is obtained by using the more hydrophobic molecule FTBTF-N as the cathode interlayer. Morphological studies suggest that design of the backbone can help to enhance short-circuit current density and fill factor.
|
|