| 1. |
- Bombarda, F., et al.
(författare)
-
Runaway electron beam control
- 2019
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 1361-6587 .- 0741-3335. ; 61:1
-
Tidskriftsartikel (refereegranskat)
|
|
| 2. |
- Krasilnikov, A., et al.
(författare)
-
Evidence of 9 Be + p nuclear reactions during 2ω CH and hydrogen minority ICRH in JET-ILW hydrogen and deuterium plasmas
- 2018
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 58:2
-
Tidskriftsartikel (refereegranskat)abstract
- The intensity of 9Be + p nuclear fusion reactions was experimentally studied during second harmonic (2ω CH) ion-cyclotron resonance heating (ICRH) and further analyzed during fundamental hydrogen minority ICRH of JET-ILW hydrogen and deuterium plasmas. In relatively low-density plasmas with a high ICRH power, a population of fast H+ ions was created and measured by neutral particle analyzers. Primary and secondary nuclear reaction products, due to 9Be + p interaction, were observed with fast ion loss detectors, γ-ray spectrometers and neutron flux monitors and spectrometers. The possibility of using 9Be(p, d)2α and 9Be(p, α)6Li nuclear reactions to create a population of fast alpha particles and study their behaviour in non-active stage of ITER operation is discussed in the paper.
|
|
| 3. |
-
- 2018
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 58:1
-
Forskningsöversikt (refereegranskat)
|
|
| 4. |
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
|
|
| 9. |
|
|
| 10. |
|
|
| 11. |
|
|
| 12. |
|
|
| 13. |
|
|
| 14. |
- Murari, A., et al.
(författare)
-
A control oriented strategy of disruption prediction to avoid the configuration collapse of tokamak reactors
- 2024
-
Ingår i: Nature Communications. - 2041-1723 .- 2041-1723. ; 15:1
-
Tidskriftsartikel (refereegranskat)abstract
- The objective of thermonuclear fusion consists of producing electricity from the coalescence of light nuclei in high temperature plasmas. The most promising route to fusion envisages the confinement of such plasmas with magnetic fields, whose most studied configuration is the tokamak. Disruptions are catastrophic collapses affecting all tokamak devices and one of the main potential showstoppers on the route to a commercial reactor. In this work we report how, deploying innovative analysis methods on thousands of JET experiments covering the isotopic compositions from hydrogen to full tritium and including the major D-T campaign, the nature of the various forms of collapse is investigated in all phases of the discharges. An original approach to proximity detection has been developed, which allows determining both the probability of and the time interval remaining before an incoming disruption, with adaptive, from scratch, real time compatible techniques. The results indicate that physics based prediction and control tools can be developed, to deploy realistic strategies of disruption avoidance and prevention, meeting the requirements of the next generation of devices.
|
|
| 15. |
|
|
| 16. |
|
|
| 17. |
|
|
| 18. |
|
|
| 19. |
|
|
| 20. |
|
|
| 21. |
|
|
| 22. |
|
|
| 23. |
|
|
| 24. |
|
|
| 25. |
|
|
| 26. |
|
|
| 27. |
|
|
| 28. |
- Joffrin, E., et al.
(författare)
-
Overview of the JET preparation for deuterium-tritium operation with the ITER like-wall
- 2019
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 59:11
-
Forskningsöversikt (refereegranskat)abstract
- For the past several years, the JET scientific programme (Pamela et al 2007 Fusion Eng. Des. 82 590) has been engaged in a multi-campaign effort, including experiments in D, H and T, leading up to 2020 and the first experiments with 50%/50% D-T mixtures since 1997 and the first ever D-T plasmas with the ITER mix of plasma-facing component materials. For this purpose, a concerted physics and technology programme was launched with a view to prepare the D-T campaign (DTE2). This paper addresses the key elements developed by the JET programme directly contributing to the D-T preparation. This intense preparation includes the review of the physics basis for the D-T operational scenarios, including the fusion power predictions through first principle and integrated modelling, and the impact of isotopes in the operation and physics of D-T plasmas (thermal and particle transport, high confinement mode (H-mode) access, Be and W erosion, fuel recovery, etc). This effort also requires improving several aspects of plasma operation for DTE2, such as real time control schemes, heat load control, disruption avoidance and a mitigation system (including the installation of a new shattered pellet injector), novel ion cyclotron resonance heating schemes (such as the three-ions scheme), new diagnostics (neutron camera and spectrometer, active Alfven eigenmode antennas, neutral gauges, radiation hard imaging systems...) and the calibration of the JET neutron diagnostics at 14 MeV for accurate fusion power measurement. The active preparation of JET for the 2020 D-T campaign provides an incomparable source of information and a basis for the future D-T operation of ITER, and it is also foreseen that a large number of key physics issues will be addressed in support of burning plasmas.
|
|
| 29. |
-
Overview of the JET results
- 2015
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 55:10
-
Tidskriftsartikel (refereegranskat)
|
|
| 30. |
- Abel, I, et al.
(författare)
-
Overview of the JET results with the ITER-like wall
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Tidskriftsartikel (refereegranskat)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 31. |
- Romanelli, F, et al.
(författare)
-
Overview of the JET results
- 2011
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Tidskriftsartikel (refereegranskat)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
| 32. |
- Labit, B., et al.
(författare)
-
Dependence on plasma shape and plasma fueling for small edge-localized mode regimes in TCV and ASDEX Upgrade
- 2019
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 59:8
-
Tidskriftsartikel (refereegranskat)abstract
- © 2019 Institute of Physics Publishing. All rights reserved. Within the EUROfusion MST1 work package, a series of experiments has been conducted on AUG and TCV devices to disentangle the role of plasma fueling and plasma shape for the onset of small ELM regimes. On both devices, small ELM regimes with high confinement are achieved if and only if two conditions are fulfilled at the same time. Firstly, the plasma density at the separatrix must be large enough (ne,sep/nG ∼ 0.3), leading to a pressure profile flattening at the separatrix, which stabilizes type-I ELMs. Secondly, the magnetic configuration has to be close to a double null (DN), leading to a reduction of the magnetic shear in the extreme vicinity of the separatrix. As a consequence, its stabilizing effect on ballooning modes is weakened.
|
|
| 33. |
- Zohm, H., et al.
(författare)
-
Overview of ASDEX upgrade results in view of ITER and DEMO
- 2024
-
Ingår i: Nuclear Fusion. - 0029-5515 .- 1741-4326. ; 64:11
-
Tidskriftsartikel (refereegranskat)abstract
- Experiments on ASDEX Upgrade (AUG) in 2021 and 2022 have addressed a number of critical issues for ITER and EU DEMO. A major objective of the AUG programme is to shed light on the underlying physics of confinement, stability, and plasma exhaust in order to allow reliable extrapolation of results obtained on present day machines to these reactor-grade devices. Concerning pedestal physics, the mitigation of edge localised modes (ELMs) using resonant magnetic perturbations (RMPs) was found to be consistent with a reduction of the linear peeling-ballooning stability threshold due to the helical deformation of the plasma. Conversely, ELM suppression by RMPs is ascribed to an increased pedestal transport that keeps the plasma away from this boundary. Candidates for this increased transport are locally enhanced turbulence and a locked magnetic island in the pedestal. The enhanced D-alpha (EDA) and quasi-continuous exhaust (QCE) regimes have been established as promising ELM-free scenarios. Here, the pressure gradient at the foot of the H-mode pedestal is reduced by a quasi-coherent mode, consistent with violation of the high-n ballooning mode stability limit there. This is suggestive that the EDA and QCE regimes have a common underlying physics origin. In the area of transport physics, full radius models for both L- and H-modes have been developed. These models predict energy confinement in AUG better than the commonly used global scaling laws, representing a large step towards the goal of predictive capability. A new momentum transport analysis framework has been developed that provides access to the intrinsic torque in the plasma core. In the field of exhaust, the X-Point Radiator (XPR), a cold and dense plasma region on closed flux surfaces close to the X-point, was described by an analytical model that provides an understanding of its formation as well as its stability, i.e., the conditions under which it transitions into a deleterious MARFE with the potential to result in a disruptive termination. With the XPR close to the divertor target, a new detached divertor concept, the compact radiative divertor, was developed. Here, the exhaust power is radiated before reaching the target, allowing close proximity of the X-point to the target. No limitations by the shallow field line angle due to the large flux expansion were observed, and sufficient compression of neutral density was demonstrated. With respect to the pumping of non-recycling impurities, the divertor enrichment was found to mainly depend on the ionisation energy of the impurity under consideration. In the area of MHD physics, analysis of the hot plasma core motion in sawtooth crashes showed good agreement with nonlinear 2-fluid simulations. This indicates that the fast reconnection observed in these events is adequately described including the pressure gradient and the electron inertia in the parallel Ohm’s law. Concerning disruption physics, a shattered pellet injection system was installed in collaboration with the ITER International Organisation. Thanks to the ability to vary the shard size distribution independently of the injection velocity, as well as its impurity admixture, it was possible to tailor the current quench rate, which is an important requirement for future large devices such as ITER. Progress was also made modelling the force reduction of VDEs induced by massive gas injection on AUG. The H-mode density limit was characterised in terms of safe operational space with a newly developed active feedback control method that allowed the stability boundary to be probed several times within a single discharge without inducing a disruptive termination. Regarding integrated operation scenarios, the role of density peaking in the confinement of the ITER baseline scenario (high plasma current) was clarified. The usual energy confinement scaling ITER98(p,y) does not capture this effect, but the more recent H20 scaling does, highlighting again the importance of developing adequate physics based models. Advanced tokamak scenarios, aiming at large non-inductive current fraction due to non-standard profiles of the safety factor in combination with high normalised plasma pressure were studied with a focus on their access conditions. A method to guide the approach of the targeted safety factor profiles was developed, and the conditions for achieving good confinement were clarified. Based on this, two types of advanced scenarios (‘hybrid’ and ‘elevated’ q-profile) were established on AUG and characterised concerning their plasma performance.
|
|
| 34. |
- Stroth, U., et al.
(författare)
-
Progress from ASDEX Upgrade experiments in preparing the physics basis of ITER operation and DEMO scenario development
- 2022
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 62:4
-
Tidskriftsartikel (refereegranskat)abstract
- An overview of recent results obtained at the tokamak ASDEX Upgrade (AUG) is given. A work flow for predictive profile modelling of AUG discharges was established which is able to reproduce experimental H-mode plasma profiles based on engineering parameters only. In the plasma center, theoretical predictions on plasma current redistribution by a dynamo effect were confirmed experimentally. For core transport, the stabilizing effect of fast ion distributions on turbulent transport is shown to be important to explain the core isotope effect and improves the description of hollow low-Z impurity profiles. The L-H power threshold of hydrogen plasmas is not affected by small helium admixtures and it increases continuously from the deuterium to the hydrogen level when the hydrogen concentration is raised from 0 to 100%. One focus of recent campaigns was the search for a fusion relevant integrated plasma scenario without large edge localised modes (ELMs). Results from six different ELM-free confinement regimes are compared with respect to reactor relevance: ELM suppression by magnetic perturbation coils could be attributed to toroidally asymmetric turbulent fluctuations in the vicinity of the separatrix. Stable improved confinement mode plasma phases with a detached inner divertor were obtained using a feedback control of the plasma β. The enhanced D α H-mode regime was extended to higher heating power by feedback controlled radiative cooling with argon. The quasi-coherent exhaust regime was developed into an integrated scenario at high heating power and energy confinement, with a detached divertor and without large ELMs. Small ELMs close to the separatrix lead to peeling-ballooning stability and quasi continuous power exhaust. Helium beam density fluctuation measurements confirm that transport close to the separatrix is important to achieve the different ELM-free regimes. Based on separatrix plasma parameters and interchange-drift-Alfvén turbulence, an analytic model was derived that reproduces the experimentally found important operational boundaries of the density limit and between L- and H-mode confinement. Feedback control for the X-point radiator (XPR) position was established as an important element for divertor detachment control. Stable and detached ELM-free phases with H-mode confinement quality were obtained when the XPR was moved 10 cm above the X-point. Investigations of the plasma in the future flexible snow-flake divertor of AUG by means of first SOLPS-ITER simulations with drifts activated predict beneficial detachment properties and the activation of an additional strike point by the drifts.
|
|
| 35. |
- Meyer, H.F., et al.
(författare)
-
Overview of physics studies on ASDEX Upgrade
- 2019
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 59:11
-
Forskningsöversikt (refereegranskat)abstract
- The ASDEX Upgrade (AUG) programme, jointly run with the EUROfusion MST1 task force, continues to significantly enhance the physics base of ITER and DEMO. Here, the full tungsten wall is a key asset for extrapolating to future devices. The high overall heating power, flexible heating mix and comprehensive diagnostic set allows studies ranging from mimicking the scrape-off-layer and divertor conditions of ITER and DEMO at high density to fully non-inductive operation (q 95 = 5.5, ) at low density. Higher installed electron cyclotron resonance heating power 6 MW, new diagnostics and improved analysis techniques have further enhanced the capabilities of AUG. Stable high-density H-modes with MW m-1 with fully detached strike-points have been demonstrated. The ballooning instability close to the separatrix has been identified as a potential cause leading to the H-mode density limit and is also found to play an important role for the access to small edge-localized modes (ELMs). Density limit disruptions have been successfully avoided using a path-oriented approach to disruption handling and progress has been made in understanding the dissipation and avoidance of runaway electron beams. ELM suppression with resonant magnetic perturbations is now routinely achieved reaching transiently . This gives new insight into the field penetration physics, in particular with respect to plasma flows. Modelling agrees well with plasma response measurements and a helically localised ballooning structure observed prior to the ELM is evidence for the changed edge stability due to the magnetic perturbations. The impact of 3D perturbations on heat load patterns and fast-ion losses have been further elaborated. Progress has also been made in understanding the ELM cycle itself. Here, new fast measurements of and E r allow for inter ELM transport analysis confirming that E r is dominated by the diamagnetic term even for fast timescales. New analysis techniques allow detailed comparison of the ELM crash and are in good agreement with nonlinear MHD modelling. The observation of accelerated ions during the ELM crash can be seen as evidence for the reconnection during the ELM. As type-I ELMs (even mitigated) are likely not a viable operational regime in DEMO studies of 'natural' no ELM regimes have been extended. Stable I-modes up to have been characterised using -feedback. Core physics has been advanced by more detailed characterisation of the turbulence with new measurements such as the eddy tilt angle - measured for the first time - or the cross-phase angle of and fluctuations. These new data put strong constraints on gyro-kinetic turbulence modelling. In addition, carefully executed studies in different main species (H, D and He) and with different heating mixes highlight the importance of the collisional energy exchange for interpreting energy confinement. A new regime with a hollow profile now gives access to regimes mimicking aspects of burning plasma conditions and lead to nonlinear interactions of energetic particle modes despite the sub-Alfvénic beam energy. This will help to validate the fast-ion codes for predicting ITER and DEMO.
|
|
| 36. |
- Hobirk, J., et al.
(författare)
-
The JET hybrid scenario in Deuterium, Tritium and Deuterium-Tritium
- 2023
-
Ingår i: Nuclear Fusion. - : Institute of Physics Publishing (IOPP). - 0029-5515 .- 1741-4326. ; 63:11
-
Tidskriftsartikel (refereegranskat)abstract
- The JET hybrid scenario has been developed from low plasma current carbon wall discharges to the record-breaking Deuterium-Tritium plasmas obtained in 2021 with the ITER-like Be/W wall. The development started in pure Deuterium with refinement of the plasma current, and toroidal magnetic field choices and succeeded in solving the heat load challenges arising from 37 MW of injected power in the ITER like wall environment, keeping the radiation in the edge and core controlled, avoiding MHD instabilities and reaching high neutron rates. The Deuterium hybrid plasmas have been re-run in Tritium and methods have been found to keep the radiation controlled but not at high fusion performance probably due to time constraints. For the first time this scenario has been run in Deuterium-Tritium (50:50). These plasmas were re-optimised to have a radiation-stable H-mode entry phase, good impurity control through edge Ti gradient screening and optimised performance with fusion power exceeding 10 MW for longer than three alpha particle slow down times, 8.3 MW averaged over 5 s and fusion energy of 45.8 MJ.
|
|
| 37. |
- Kiptily, V. G., et al.
(författare)
-
Observation of alpha-particles in recent D-T experiments on JET
- 2024
-
Ingår i: Nuclear Fusion. - : Institute of Physics (IOP). - 0029-5515 .- 1741-4326. ; 64:8
-
Tidskriftsartikel (refereegranskat)abstract
- The fusion reaction between deuterium and tritium, D(T,n)4 He is the main source of energy in future thermonuclear reactors. Alpha-particles (4 He-ions) born with an average energy of 3.5 MeV transferring energy to the thermal plasma during their slowing down, should provide the self-sustained D-T plasma burn. The adequate confinement of alpha-particles is essential to provide efficient heating of the bulk plasma and steady burning of a reactor plasma. That is why the fusion-born alpha-particle studies have been a priority task in the second D-T experiments (DTE2) on the Joint European Torus (JET) to understand the main mechanisms of their slowing down, redistribution and losses and to develop optimal plasma scenarios. JET with Be-wall and W-divertor, enhanced auxiliary heating systems and improved energetic-particle diagnostic capabilities, producing significant population of alpha-particles, provided the possibility for comprehensive studying of the alpha-particle behaviour. Selected results of the confined and lost alpha-particle measurements, evidence of alpha-particle self-heating and assessments of the fusion performance are presented in this paper giving an opportunity for further modelling and extrapolation to the International Thermonuclear Experimental Reactor and burning plasma reactors.
|
|
| 38. |
- Voitsekhovitch, I., et al.
(författare)
-
Integrated modelling for tokamak plasma: Physics and scenario optimisation
- 2012
-
Ingår i: 39th EPS Conference on Plasma Physics 2012, EPS 2012 and the 16th International Congress on Plasma Physics; Stockholm; Sweden; 2 July 2012 through 6 July 2012; Code 96757. - 9781622769810 ; 2, s. 1314-1317
-
Konferensbidrag (refereegranskat)abstract
- Simulations of JET and AUG HS with the GLF23 model show that the observed core confinement improvement can be partly explained by the beneficial s/q effect on the ITG driven transport while the effect of the ExB shear stabilisation is weaker than in H-mode plasmas. Strong stabilising effect of βe on the ITG turbulence has been found, but the transport reduction due to this effect can be limited by the onset of the KBM mode at high βe. The simulations of toroidal rotation in HS with the GLF23 model give an indication of the toroidal momentum pinch (Pr
|
|
| 39. |
- Joffrin, E., et al.
(författare)
-
First scenario development with the JET new ITER-like wall
- 2014
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 54:1, s. 013011-
-
Tidskriftsartikel (refereegranskat)abstract
- In the recent JET experimental campaigns with the new ITER-like wall (JET-ILW), major progress has been achieved in the characterization and operation of the H-mode regime in metallic environments: (i) plasma breakdown has been achieved at the first attempt and X-point L-mode operation recovered in a few days of operation; (ii) stationary and stable type-I ELMy H-modes with beta(N) similar to 1.4 have been achieved in low and high triangularity ITER-like shape plasmas and are showing that their operational domain at H = 1 is significantly reduced with the JET-ILW mainly because of the need to inject a large amount of gas (above 10(22) Ds(-1)) to control core radiation; (iii) in contrast, the hybrid H-mode scenario has reached an H factor of 1.2-1.3 at beta(N) of 3 for 2-3 s; and, (iv) in comparison to carbon equivalent discharges, total radiation is similar but the edge radiation is lower and Z(eff) of the order of 1.3-1.4. Strong core radiation peaking is observed in H-mode discharges at a low gas fuelling rate (i. e. below 0.5 x 10(22) Ds(-1)) and low ELM frequency (typically less than 10 Hz), even when the tungsten influx from the diverter is constant. High-Z impurity transport from the plasma edge to the core appears to be the dominant factor to explain these observations. This paper reviews the major physics and operational achievements and challenges that an ITER-like wall configuration has to face to produce stable plasma scenarios with maximized performance.
|
|
| 40. |
|
|
| 41. |
- Lerche, E., et al.
(författare)
-
Optimization of ICRH for core impurity control in JET-ILW
- 2016
-
Ingår i: Nuclear Fusion. - JET, Culham Sci Ctr, EUROfus Consortium, Abingdon OX14 3DB, Oxon, England. [Lerche, E.; Van Eester, D.; Crombe, K.; Kazakov, Y.; Krivska, A.; Ongena, J.] TEC Partner, Assoc EUROFUS Belgian State, LPP ERM KMS, Brussels, Belgium. [Lerche, E.; Jacquet, P.; Giroud, C.; Monakhov, I.; Casson, F. J.; Rimini, F.; Blackman, T.; Brix, M.; Challis, C.; Graham, M.; Kiptily, V.; Lennholm, M.; Lomas, P.; Maggi, C.; Mathews, G.; Mayoral, M. -L.; Santala, M.; Shaw, A.; Stamp, M.] Euratom CCFE Fus Assoc, Culham Sci Ctr, Abingdon, Oxon, England. [Goniche, M.; Colas, L.; Fedorczak, N.; Joffrin, E.; Monier-Garbet, P.] Assoc EUROFUS CEA, IRFM, St Paul Les Durance, France. [Bobkov, V.; Angioni, C.; Hobirk, J.; Puetterich, T.; Reich, M.] EUROFUS Assoziat, Max Planck Inst Plasmaphys, Garching, Germany. [Baruzzo, M.] EUROFUS ENEA Assoc, Consorzio RFX, Padua, Italy. [Brezinsek, S.] TEC Partner, EUROFUS Assoziat, Forschungszentrum Juelich, Julich, Germany. [Czarnecka, A.] EUROFUS Assoc, IPPLM, Warsaw, Poland. [Eriksson, J.] Uppsala Univ, Dept Phys & Astron, Assoc EUROFUS VR, Uppsala, Sweden. [Graves, J. P.] Assoc EUROFUS Confederat Suisse, CRPP EPFL, Lausanne, Switzerland. [Gorini, G.; Mantica, P.; Nocente, M.; Tardocchi, M.; Valisa, M.] EUROFUS ENEA CNR Assoc, Inst Fis Plasma, Milan, Italy. [Johnson, T.] KTH, EES, Fus Plasma Phys, Assoc EUROFUS VR, Stockholm, Sweden. [Meneses, L.; Nave, M. F.; Nunes, I.] EUROFUS IST Assoc, Inst Plasmas & Fusao Nucl, Lisbon, Portugal. [Mlynar, J.; Petrzilka, V.] EUROFUS IPP CR Assoc, Inst Plasma Phys, Prague, Czech Republic. [Petravich, G.] EUROFUS Assoc, MTA Wigner FK RMI, Budapest, Hungary. [Solano, E. R.] EUROFUS Assoc, LNF CIEMAT, Madrid, Spain. [Solano, E. R.] Culham Sci Ctr, EUROfus PMU, Abingdon OX14 3DB, Oxon, England. [Sips, G.] Culham Sci Ctr, JET Exploitat Unit, Abingdon OX14 3DB, Oxon, England. [Tsalas, M.] EUROFUS Assoc, FOM Inst DIFFER, Nieuwegein, Netherlands. : Institute of Physics (IOP). - 0029-5515 .- 1741-4326. ; 56:3
-
Tidskriftsartikel (refereegranskat)abstract
- Ion cyclotron resonance frequency (ICRF) heating has been an essential component in the development of high power H-mode scenarios in the Jet European Torus ITER-like wall (JET-ILW). The ICRF performance was improved by enhancing the antenna-plasma coupling with dedicated main chamber gas injection, including the preliminary minimization of RF-induced plasma-wall interactions, while the RF heating scenarios where optimized for core impurity screening in terms of the ion cyclotron resonance position and the minority hydrogen concentration. The impact of ICRF heating on core impurity content in a variety of 2.5 MA JET-ILW H-mode plasmas will be presented, and the steps that were taken for optimizing ICRF heating in these experiments will be reviewed.
|
|
| 42. |
- Challis, C. D., et al.
(författare)
-
Improved confinement in JET high β plasmas with an ITER-like wall
- 2015
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 55:5
-
Tidskriftsartikel (refereegranskat)abstract
- The replacement of the JET carbon wall (C-wall) by a Be/W ITER-like wall (ILW) has affected the plasma energy confinement. To investigate this, experiments have been performed with both the C-wall and ILW to vary the heating power over a wide range for plasmas with different shapes. It was found that the power degradation of thermal energy confinement was weak with the ILW; much weaker than the IPB98(y,2) scaling and resulting in an increase in normalized confinement from H98 ∼ 0.9 at βN ∼ 1.5 to H98 ∼ 1.2-1.3 at βN ∼ 2.5 - 3.0 as the power was increased (where H98 = τE/τIPB98(y,2) and βN = βTBT/aIP in % T/mMA). This reproduces the general trend in JET of higher normalized confinement in the so-called 'hybrid' domain, where normalized β is typically above 2.5, compared with 'baseline' ELMy H-mode plasmas with βN ∼ 1.5 - 2.0. This weak power degradation of confinement, which was also seen with the C-wall experiments at low triangularity, is due to both increased edge pedestal pressure and core pressure peaking at high power. By contrast, the high triangularity C-wall plasmas exhibited elevated H98 over a wide power range with strong, IPB98(y,2)-like, power degradation. This strong power degradation of confinement appears to be linked to an increase in the source of neutral particles from the wall as the power increased, an effect that was not reproduced with the ILW. The reason for the loss of improved confinement domain at low power with the ILW is yet to be clarified, but contributing factors may include changes in the rate of gas injection, wall recycling, plasma composition and radiation. The results presented in this paper show that the choice of wall materials can strongly affect plasma performance, even changing confinement scalings that are relied upon for extrapolation to future devices.
|
|
| 43. |
|
|
| 44. |
|
|
| 45. |
- Kirov, K. K., et al.
(författare)
-
Analysis of fusion alphas interaction with RF waves in D-T plasma at JET
- 2024
-
Ingår i: Nuclear Fusion. - : Institute of Physics Publishing (IOPP). - 0029-5515 .- 1741-4326. ; 64:8
-
Tidskriftsartikel (refereegranskat)abstract
- This work studies the influence of radio frequency (RF) waves in the ion cyclotron resonance heating (ICRH) range of frequencies on fusion alphas during the recent JET D-T campaign. Fusion alphas from D-T reactions are created with energies of about 3.5 MeV and therefore have significant Doppler shifts enabling synergistic interactions between them and RF waves at a broad range of frequencies, including the ones foreseen for future fusion machines in ITER (Schneider et al 2021 Nucl. Fusion 61 126058) and SPARC (Creely et al 2020 J. Plasma Phys. 86 865860502). Resonant interactions between RF waves and alphas, also called synergistic effects, will modify the alpha distribution and ultimately will have an impact on alpha orbit losses and heating. Data from JET 3.43 T/2.3 MA pulses based on the hybrid scenario (Hobirk et al 2023 Nucl. Fusion; Hobirk et al 29th IAEA FEC23 Conf. (16-21 October 2023); Challis et al 48th EPS Conf. on Plasma Physics (27 June-1 July 2022) during the DTE2 campaign (Maggi et al 2023 Nucl. Fusion)) were used for the analysis in this study. The impact of synergistic effects on alpha orbit losses and alpha heating are assessed. The conclusions are based on the analysis of experimental data for fast alpha losses, i.e. measurements from neutral particle analyser (NPA), fast ion losses scintillator detector, Faraday cups (FCs), and TRANSP (Hawryluk et al 1980 Physics of Plasmas Close to Thermonuclear Conditions vol 1 (CEC) pp 19-46) simulations. Experimental data and TRANSP analysis indicates that there are indeed changes in the alpha distribution function (DF) due to interaction with RF waves. Data from the NPA show increased 4He flux in the range from a few hundred keV up to 800 keV for pulses with RF power, while TRANSP clearly shows modifications in the fast alpha DF for these energies. Data from the scintillator detector and the FCs were compared for pulses with and without ICRH power and versus cases with enhanced alpha losses due to MHD activity. The trends from these diagnostics consistently show no additional alpha losses due to interaction with RF waves. TRANSP predictions for the impact of ynergistic effects on alpha heating show up to a 42% increase in alpha electron heating and up to a 25% increase in alpha ion heating. These effects, however, become negligibly small, less than 1%, when alpha heating is compared to the total auxiliary heating power in the investigated JET pulses.
|
|
| 46. |
|
|
| 47. |
- Mantsinen, M. J., et al.
(författare)
-
Experiments in high-performance JET plasmas in preparation of second harmonic ICRF heating of tritium in ITER
- 2023
-
Ingår i: Nuclear Fusion. - : Institute of Physics (IOP). - 0029-5515 .- 1741-4326. ; 63:11
-
Tidskriftsartikel (refereegranskat)abstract
- The reference ion cyclotron resonance frequency (ICRF) heating schemes for ITER deuterium-tritium (D-T) plasmas at the full magnetic field of 5.3 T are second harmonic heating of T and 3He minority heating. The wave-particle resonance location for these schemes coincide and are central at a wave frequency of 53 MHz at 5.3 T. Experiments have been carried out in the second major D-T campaign (DTE2) at JET, and in its prior D campaigns, to integrate these ICRF scenarios in JET high-performance plasmas and to compare their performance with the commonly used hydrogen (H) minority heating. In 50:50 D:T plasmas, up to 35% and 5% larger fusion power and diamagnetic energy content, respectively, were obtained with second harmonic heating of T as compared to H minority heating at comparable total input powers and gas injection rates. The core ion temperature was up to 30% and 20% higher with second harmonic T and 3He minority heating, respectively, with respect to H minority heating. These are favourable results for the use of these scenarios in ITER and future fusion reactors. According to modelling, adding ICRF heating to neutral beam injection using D and T beams resulted in a 10%-20% increase of on-axis bulk ion heating in the D-T plasmas due to its localisation in the plasma core. Central power deposition was confirmed with the break-in-slope and fast Fourier transform analysis of ion and electron temperature in response to ICRF modulation. The tail temperature of fast ICRF-accelerated tritons, their enhancement of the fusion yield and time behaviour as measured by an upgraded magnetic proton recoil spectrometer and neutral particle analyser were found in agreement with theoretical predictions. No losses of ICRF-accelerated ions were observed by fast ion detectors, which was as expected given the high plasma density of n e approximate to 7-8 x 1019 m-3 in the main heating phase that limited the formation of ICRF-accelerated fast ion tails. 3He was introduced in the machine by 3He gas injection, and the 3He concentration was measured by a high-resolution optical penning gauge in the sub-divertor region. The DTE2 experiments with 3He minority heating were carried with a low 3He concentration in the range of 2%-4% given the fact that the highest neutron rates with 3He minority heating in D plasmas were obtained at low 3He concentrations of similar to 2%, which also coincided with the highest plasma diamagnetic energy content. In addition to 3He introduced by 3He gas injection, an intrinsic concentration of 3He of the order of 0.2%-0.4% was measured in D-T plasmas before 3He was introduced in the device, which is attributed to the radioactive decay of tritium to 3He. According to modelling, even such low intrinsic concentrations of 3He lead to significant changes in ICRF power partitioning during second harmonic heating of T due to absorption of up to 30% of the wave power by 3He.
|
|
| 48. |
- Beurskens, M. N. A., et al.
(författare)
-
Global and pedestal confinement in JET with a Be/W metallic wall
- 2014
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 54:4, s. 043001-
-
Tidskriftsartikel (refereegranskat)abstract
- Type I ELMy H-mode operation in JET with the ITER-like Be/W wall (JET-ILW) generally occurs at lower pedestal pressures compared to those with the full carbon wall (JET-C). The pedestal density is similar but the pedestal temperature where type I ELMs occur is reduced and below to the so-called critical type I-type III transition temperature reported in JET-C experiments. Furthermore, the confinement factor H-98(y,H- 2) in type I ELMy H-mode baseline plasmas is generally lower in JET-ILWcompared to JET-C at low power fractions Ploss/P-thr,(08)< 2 (where P-loss is (P-in-dW/dt), and P-thr,(08) the L-H power threshold from Martin et al 2008 (J. Phys. Conf. Ser. 123 012033)). Higher power fractions have thus far not been achieved in the baseline plasmas. At Ploss/P-thr,P- 08 > 2, the confinement in JET-ILW hybrid plasmas is similar to that in JET-C. A reduction in pedestal pressure is the main reason for the reduced confinement in JET-ILW baseline ELMy H-mode plasmas where typically H-98((y, 2)) = 0.8 is obtained, compared to H-98((y, 2)) = 1.0 in JET-C. In JET-ILW hybrid plasmas a similarly reduced pedestal pressure is compensated by an increased peaking of the core pressure profile resulting in H-98((y, 2)) <= 1.25. The pedestal stability has significantly changed in high triangularity baseline plasmas where the confinement loss is also most apparent. Applying the same stability analysis for JET-C and JET-ILW, the measured pedestal in JET-ILW is stable with respect to the calculated peeling-ballooning stability limit and the ELM collapse time has increased to 2ms from typically 200 mu s in JET-C. This indicates that changes in the pedestal stability may have contributed to the reduced pedestal confinement in JET-ILW plasmas. A comparison of EPED1 pedestal pressure prediction with JET-ILW experimental data in over 500 JET-C and JET-ILW baseline and hybrid plasmas shows a good agreement with 0.8 < (measured p(ped))/(predicted p(ped), EPED) < 1.2, but that the role of triangularity is generally weaker in the JET-ILW experimental data than in the model predictions.
|
|
| 49. |
- Beurskens, M. N. A., et al.
(författare)
-
The effect of a metal wall on confinement in JET and ASDEX Upgrade
- 2013
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 55:12, s. 124043-
-
Tidskriftsartikel (refereegranskat)abstract
- In both JET and ASDEX Upgrade (AUG) the plasma energy confinement has been affected by the presence of a metal wall by the requirement of increased gas fuelling to avoid tungsten pollution of the plasma. In JET with a beryllium/tungsten wall the high triangularity baseline H-mode scenario (i.e. similar to the ITER reference scenario) has been the strongest affected and the benefit of high shaping to give good normalized confinement of H-98 similar to 1 at high Greenwald density fraction of f(GW) similar to 0.8 has not been recovered to date. In AUG with a full tungsten wall, a good normalized confinement H-98 similar to 1 could be achieved in the high triangularity baseline plasmas, albeit at elevated normalized pressure beta(N) > 2. The confinement lost with respect to the carbon devices can be largely recovered by the seeding of nitrogen in both JET and AUG. This suggests that the absence of carbon in JET and AUG with a metal wall may have affected the achievable confinement. Three mechanisms have been tested that could explain the effect of carbon or nitrogen (and the absence thereof) on the plasma confinement. First it has been seen in experiments and by means of nonlinear gyrokinetic simulations (with the GENE code), that nitrogen seeding does not significantly change the core temperature profile peaking and does not affect the critical ion temperature gradient. Secondly, the dilution of the edge ion density by the injection of nitrogen is not sufficient to explain the plasma temperature and pressure rise. For this latter mechanism to explain the confinement improvement with nitrogen seeding, strongly hollow Z(eff) profiles would be required which is not supported by experimental observations. The confinement improvement with nitrogen seeding cannot be explained with these two mechanisms. Thirdly, detailed pedestal structure analysis in JET high triangularity baseline plasmas have shown that the fuelling of either deuterium or nitrogen widens the pressure pedestal. However, in JET-ILW this only leads to a confinement benefit in the case of nitrogen seeding where, as the pedestal widens, the obtained pedestal pressure gradient is conserved. In the case of deuterium fuelling in JET-ILW the pressure gradient is strongly degraded in the fuelling scan leading to no net confinement gain due to the pedestal widening. The pedestal code EPED correctly predicts the pedestal pressure of the unseeded plasmas in JET-ILW within +/- 5%, however it does not capture the complex variation of pedestal width and gradient with fuelling and impurity seeding. Also it does not predict the observed increase of pedestal pressure by nitrogen seeding in JET-ILW. Ideal peeling ballooning MHD stability analysis shows that the widening of the pedestal leads to a down shift of the marginal stability boundary by only 10-20%. However, the variations in the pressure gradient observed in the JET-ILW fuelling experiment is much larger and spans a factor of more than two. As a result the experimental points move from deeply unstable to deeply stable on the stability diagram in a deuterium fuelling scan. In AUG-W nitrogen seeded plasmas, a widening of the pedestal has also been observed, consistent with the JET observations. The absence of carbon can thus affect the pedestal structure, and mainly the achieved pedestal gradient, which can be recovered by seeding nitrogen. The underlying physics mechanism is still under investigation and requires further understanding of the role of impurities on the pedestal stability and pedestal structure formation.
|
|
| 50. |
- Challis, C. D., et al.
(författare)
-
High βN JET H-modes for steady-state application
- 2007
-
Ingår i: 34th EPS Conference on Plasma Physics 2007, EPS 2007 - Europhysics Conference Abstracts. - : European Physical Society. - 9781622763344 ; , s. 2118-2121
-
Konferensbidrag (refereegranskat)
|
|
