| 1. |
- Andersson, Mattias, et al.
(författare)
-
Mixed C60/C70 based fullerene acceptors in polymer bulk-heterojunction solar cells
- 2012
-
Ingår i: Organic Electronics: physics, materials, applications. - : Elsevier BV. - 1566-1199 .- 1878-5530. ; 13:12, s. 2856-2864
-
Tidskriftsartikel (refereegranskat)abstract
- Different mixtures of identically substituted C60 and C70 based fullerens have been used as acceptors in three polymer: fullerene systems that strongly express various performance limiting aspects of bulk heterojunction solar cells. Results are correlated with, and discussed in terms of e.g. morphology, charge separation, and charge transport. In these systems, there appears to be no relevant differences in either mobility or energy level positions between the identically substituted C60 and C70 based fullerenes tested. Examples of how fullerene mixtures influence the nano-morphology of the active layer are given. An upper limit to the open circuit voltage that can be obtained with fullerenes is also suggested.
|
|
| 2. |
- Camacho Dejay, Rafael, et al.
(författare)
-
Polarization Imaging of Emissive Charge Transfer States in Polymer/Fullerene Blends
- 2014
-
Ingår i: Chemistry of Materials. - : American Chemical Society (ACS). - 0897-4756 .- 1520-5002. ; 26:23, s. 6695-6704
-
Tidskriftsartikel (refereegranskat)abstract
- Photoexcitation of conjugated polymerfullerene blends results in population of a local charge transfer (CT) state at the interface between the two materials. The competition between recombination and dissociation of this interfacial state limits the generation of fully separated free charges. Therefore, a detailed understanding of the CT states is critical for building a comprehensive picture of the organic solar cells operation. We applied a new fluorescence microscopy method called two-dimensional polarization imaging to gain insight into the orientation of the transition dipole moments of the CT states, and the associated excitation energy transfer processes in TQ1:PCBM blend films. The polymer phase was oriented mechanically to relate the polymer dipole moment orientation to that of the CT states. CT state formation was observed to be much faster than energy transfer in the polymer phase. However, after being formed an emissive CT state does not exchange excitation energy with other CT states, suggesting that they are spatially and/or energetically isolated. We found that the quantum yield of the CT emission is smaller for CT states spatially located in the highly oriented polymer domains, which is interpreted as the result of enhanced CT state dissociation in highly ordered structures.
|
|
| 3. |
- Gadisa, Abay, et al.
(författare)
-
Bipolar Charge Transport in Fullerene Molecules in a Bilayer and Blend of Polyfluorene Copolymer and Fullerene
- 2010
-
Ingår i: ADVANCED MATERIALS. - : Wiley. - 0935-9648. ; 22:9, s. 1008-
-
Tidskriftsartikel (refereegranskat)abstract
- Efficient polymer solar cells typically contain the fullerene derivative [6,6]-phenyl-C61-butyric acid methyl ester (PCBM), which promotes dissociation of excited states and enhances charge transport. The ability of PCBM to transport holes in solar cell bulk heterojunction films is monitored via the electroluminescence emission of a bulk heterojunction blend of PCBM and a polyfluorene copolymer. In polymer/fullerene bilayer diodes, fullerene emission is also observed.
|
|
| 4. |
- Ma, Zaifei, et al.
(författare)
-
Enhance performance of organic solar cells based on an isoindigo-based copolymer by balancing absorption and miscibility of electron acceptor
- 2011
-
Ingår i: Applied Physics Letters. - : AIP Publishing. - 0003-6951 .- 1077-3118. ; 99:14
-
Tidskriftsartikel (refereegranskat)abstract
- Superior absorption of PC(71)BM in visible region to that of PC(61)BM makes PC(71)BM a predominant acceptor for most high efficient polymer solar cells (PSCs). However, we will demonstrate that power conversion efficiencies (PCEs) of PSCs based on poly[N,N'-bis(2-hexyldecyl)isoindigo-6, 6'-diyl-alt-thiophene-2,5-diyl] (PTI-1) with PC(61)BM as acceptor are 50% higher than their PC71BM counterparts under illumination of AM1.5G. AFM images reveal different topographies of the blends between PTI-1:PC(61)BM and PTI-1:PC(71)BM, which suggests that acceptor's miscibility plays a more important role than absorption. The photocurrent of 9.1 mA/cm(2) is among the highest value in PSCs with a driving force for exciton dissociation less than 0.2 eV.
|
|
| 5. |
- Ma, Zaifei, et al.
(författare)
-
Structure-Property Relationships of Oligothiophene-Isoindigo Polymers for Efficient Bulk-Heterojunction Solar Cells
- 2014
-
Ingår i: energy and environmental science. - : Royal Society of Chemistry. - 1754-5692. ; 17:1, s. 361-369
-
Tidskriftsartikel (refereegranskat)abstract
- A series of alternating oligothiophene (nT)-isoindigo (I) copolymers (PnTI) were synthesized to investigate the influence of the oligothiophene block length on the photovoltaic (PV) properties of PnTI:PCBM bulk-heterojunction blends. Our study indicates that the number of thiophene rings (n) in the repeating unit alters both, polymer crystallinity and polymer-fullerene interfacial energetics, which results in a decreasing open-circuit voltage (Voc) of the solar cells with increasing n. The short-circuit current density (Jsc) of P1TI:PCBM devices is limited by the absence of a significant driving force for electron transfer. Instead, blends based on P5TI and P6TI feature large polymer domains, which limit charge generation and thus Jsc. The best PV performance with a power conversion efficiency of up to 6.9% was achieved with devices based on P3TI, where a combination of favorable morphology and optimal interface energy level offset ensures efficient exciton separation and charge generation. The structure-property relationship demonstrated in this work is a valuable guideline for the design of high performance polymers with small energy losses during the charge generation process, allowing for the fabrication of efficient solar cells that combine a minimal loss in Voc with a high Jsc.
|
|
| 6. |
- Makhinia, Anatolii, et al.
(författare)
-
Toward Sustainability in All-Printed Accumulation Mode Organic Electrochemical Transistors
- 2024
-
Ingår i: Advanced Functional Materials. - : John Wiley & Sons, Ltd. - 1616-301X .- 1616-3028.
-
Tidskriftsartikel (refereegranskat)abstract
- Abstract This study reports on the first all-printed vertically stacked organic electrochemical transistors (OECTs) operating in accumulation mode; the devices, relying on poly([4,4?-bis(2-(2-(2-methoxyethoxy)ethoxy)ethoxy)-2,2?-bithiophen-5,5?-diyl]-alt-[thieno[3,2-b]thiophene-2,5-diyl]) (pgBTTT) as the active channel material, are fabricated via a combination of screen and inkjet printing technologies. The resulting OECTs (W/L ≈5) demonstrate good switching performance; gm, norm ≈13 mS cm?1, µC* ≈21 F cm?1 V?1 s?1, ON?OFF ratio > 104 and good cycling stability upon continuous operation for 2 h. The inkjet printing process of pgBTTT is established by first solubilizing the polymer in dihydrolevoglucosenone (Cyrene), a non-toxic, cellulose-derived, and biodegradable solvent. The resulting ink formulations exhibit good jettability, thereby providing reproducible and stable p-type accumulation mode all-printed OECTs with high performance. Besides the environmental and safety benefits of this solvent, this study also demonstrates the assessment of how the solvent affects the performance of spin-coated OECTs, which justifies the choice of Cyrene as an alternative to commonly used harmful solvents such as chloroform, also from a device perspective. Hence, this approach shows a new possibility of obtaining more sustainable printed electronic devices, which will eventually result in all-printed OECT-based logic circuits operating in complementary mode.
|
|
| 7. |
- Melianas, Armantas, 1988-, et al.
(författare)
-
Charge Transport in Pure and Mixed Phases in Organic Solar Cells
- 2017
-
Ingår i: Advanced Energy Materials. - : John Wiley & Sons. - 1614-6832 .- 1614-6840. ; 7:20
-
Tidskriftsartikel (refereegranskat)abstract
- In organic solar cells continuous donor and acceptor networks are considered necessary for charge extraction, whereas discontinuous neat phases and molecularly mixed donor–acceptor phases are generally regarded as detrimental. However, the impact of different levels of domain continuity, purity, and donor–acceptor mixing on charge transport remains only semiquantitatively described. Here, cosublimed donor–acceptor mixtures, where the distance between the donor sites is varied in a controlled manner from homogeneously diluted donor sites to a continuous donor network are studied. Using transient measurements, spanning from sub-picoseconds to microseconds photogenerated charge motion is measured in complete photovoltaic devices, to show that even highly diluted donor sites (5.7%–10% molar) in a buckminsterfullerene matrix enable hole transport. Hopping between isolated donor sites can occur by long-range hole tunneling through several buckminsterfullerene molecules, over distances of up to ≈4 nm. Hence, these results question the relevance of “pristine” phases and whether a continuous interpenetrating donor–acceptor network is the ideal morphology for charge transport.
|
|
| 8. |
- Müller, Christian, et al.
(författare)
-
Phase behaviour of liquid-crystalline polymer/fullerene organic photovoltaic blends : thermal stability and miscibility
- 2011
-
Ingår i: Journal of Materials Chemistry. - : RSC Publishing. - 0959-9428 .- 1364-5501. ; 21, s. 10676-10684
-
Tidskriftsartikel (refereegranskat)abstract
- The thermal behaviour of an organic photovoltaic (OPV) binary system comprised of a liquidcrystalline fluorene-based polymer and a fullerene derivative is investigated. We employ variabletemperature ellipsometry complemented by photo- and electroluminescence spectroscopy as well as optical microscopy and scanning force nanoscopy to explore phase transitions of blend thin films. The high glass transition temperature correlates with the good thermal stability of solar cells based on these materials. Furthermore, we observe partial miscibility of the donor and acceptor together with the tendency of excess fullerene derivative to segregate into exceedingly large domains. Thus, for charge generation less adequate bulk-heterojunction nanostructures are poised to develop if this mixture is exposed to more elevated temperatures. Gratifyingly, the solubility of the fullerene derivative in the polymer phase is found to decrease if a higher molecular-weight polymer fraction is employed, which offers routes towards improving the photovoltaic performance of non-crystalline OPV blends.
|
|
| 9. |
- Tang, Zheng, et al.
(författare)
-
Interlayer for Modified Cathode in Highly Efficient Inverted ITO-Free Organic Solar Cells
- 2012
-
Ingår i: Advanced Materials. - : Wiley. - 0935-9648 .- 1521-4095. ; 24:4, s. 554-
-
Tidskriftsartikel (refereegranskat)abstract
- Inverted polymer solar cells with a bottom metal cathode modified by a conjugated polymer interlayer show considerable improvement of photocurrent and fill factor, which is due to hole blocking at the interlayer, and a modified surface energy which affects the nanostructure in the TQ1/[70]PCBM blend.
|
|
| 10. |
- Tang, Zheng, et al.
(författare)
-
Semi-Transparent Tandem Organic Solar Cells with 90% Internal Quantum Efficiency
- 2012
-
Ingår i: Advanced Energy Materials. - : Wiley. - 1614-6840 .- 1614-6832. ; 2:12, s. 1467-1476
-
Tidskriftsartikel (refereegranskat)abstract
- Semi-transparent (ST) organic solar cells with potential application as power generating windows are studied. The main challenge is to find proper transparent electrodes with desired electrical and optical properties. In this work, this is addressed by employing an amphiphilic conjugated polymer PFPA-1 modified ITO coated glass substrate as the ohmic electron-collecting cathode and PEDOT:PSS PH1000 as the hole-collecting anode. For active layers based on different donor polymers, considerably lower reflection and parasitic absorption are found in the ST solar cells as compared to solar cells in the standard geometry with an ITO/PEDOT:PSS anode and a LiF/Al cathode. The ST solar cells have remarkably high internal quantum efficiency at short circuit condition (similar to 90%) and high transmittance (similar to 50%). Hence, efficient ST tandem solar cells with enhanced power conversion efficiency (PCE) compared to a single ST solar cell can be constructed by connecting the stacked two ST sub-cells in parallel. The total loss of photons by reflection, parasitic absorption and transmission in the ST tandem solar cell can be smaller than the loss in a standard solar cell based on the same active materials. We demonstrate this by stacking five separately prepared ST cells on top of each other, to obtain a higher photocurrent than in an optimized standard solar cell.
|
|
| 11. |
- Tvingstedt, Kristofer, et al.
(författare)
-
Electroluminescence from Charge Transfer States in Polymer Solar Cells
- 2009
-
Ingår i: JOURNAL OF THE AMERICAN CHEMICAL SOCIETY. - : American Chemical Society (ACS). - 0002-7863 .- 1520-5126. ; 131:33, s. 11819-11824
-
Tidskriftsartikel (refereegranskat)abstract
- In this article we report the weak but omnipresent electroluminescence (EL) from several types of organic polymer:fullerene bulk heterojunction solar cells biased in the forward direction. The light emitted from blends of Some commonly used polymers and the fullerene molecule is significantly different from that of any of the pure materials comprising the blend. The lower energy of the blend EL is found to correlate with both the voltage onset of emission and the open-circuit voltage of the photovoltaic cell under solar illumination. WE., accordingly interpret the emission to originate from interfacial charge transfer state recombination and emphasize EL as a very valuable tool to characterize the charge transfer state present in donor/acceptor organic photovoltaic (OPV) cells.
|
|
| 12. |
- Tvingstedt, Kristofer, et al.
(författare)
-
On the Dissociation Efficiency of Charge Transfer Excitons and Frenkel Excitons in Organic Solar Cells: A Luminescence Quenching Study
- 2010
-
Ingår i: The Journal of Physical Chemistry C. - : American Chemical Society. - 1932-7447 .- 1932-7455. ; 114:49, s. 21824-21832
-
Tidskriftsartikel (refereegranskat)abstract
- The field dependence of photocurrent found in many organic solar cells is a significant and detrimental setback for internal quantum efficiency. In this work we study the important contribution to this field dependence due to the dissociation efficiency of the weakly bound interfacial charge transfer (CT) state, crucial for organic bulk heterojunction solar cells. Three different donor polymers and two different acceptors are examined, and their respective dissociation characteristics are evaluated by photoluminescence (PL) quenching, both for Frenkel excitons and for the intermolecular charge transfer excitons. We observe that while the field-dependent photocurrent for pure polymers does correlate well with quenching efficiency, the CT exciton quenching from the blend generally displays a less pronounced correlation with extracted photocurrent. We further note that while the electroluminescence and photoluminescence of the pure polymer are identical, we observe a red shift for the blend electroluminescence. This indicates that lower energetic states, not visible in PL, are available in the blend. The emissive state of the blends probed by PL is therefore proposed to originate from sites that are involved in photocurrent generation to a lesser extent.
|
|
| 13. |
- Vandewal, Koen, et al.
(författare)
-
Charge-Transfer States and Upper Limit of the Open-Circuit Voltage in Polymer: Fullerene Organic Solar Cells
- 2010
-
Ingår i: IEEE JOURNAL OF SELECTED TOPICS IN QUANTUM ELECTRONICS. - : Institute of Electrical and Electronics Engineers (IEEE). - 1077-260X. ; 16:6, s. 1676-1684
-
Tidskriftsartikel (refereegranskat)abstract
- The power conversion efficiency of polymer: fullerene bulk heterojunction solar cells depends on the generated photocurrent and photovoltage. Here we show, using the thermodynamic theory of detailed balance, that the photovoltage in particular is limited by the presence of polymer: fullerene material interaction, resulting in the formation of a weak donor-acceptor charge transfer complex (CTC). Excited CTCs, or charge transfer (CT) states, are visible in highly sensitive measurements of the absorption and photovoltaic action spectrum, or in photoluminescence and electroluminescence measurements. It is shown that photovoltaic and electroluminescent actions of the polymer: fullerene CTC are related by a reciprocity relation. This relation reproduces the measured open-circuit voltage (V-oc) of the photovoltaic device under solar conditions. Also, the temperature and illumination intensity dependence of V-oc is reproduced by the theory. Assuming perfect conditions for charge generation and recombination, a maximum obtainable V-oc value in function of polymer: fullerene CTC properties is derived.
|
|
| 14. |
- Vandewal, Koen, et al.
(författare)
-
Charge Transfer States in Organic Donor-Acceptor Solar Cells
- 2011
-
Ingår i: Semiconductors and semimetals. - : Academic Press. - 0080-8784. ; 85, s. 261-295
-
Tidskriftsartikel (refereegranskat)abstract
- For an efficient conversion of photons to electrons by organic materials used for photovoltaic applications, the presence of a material interface between an electron-donating and electron-accepting material is crucial. This chapter deals with the interfacial charge transfer states formed at such interfaces under solar illumination. Absorption of long-wavelength light, with energy lower than the optical gap of both donor and acceptor results in the direct formation of these charge transfer states. Decay of CT states to the ground state will result in weak light emission. Both CT absorption and emission will be linked to photovoltaic performance. The role of the CT state in determining the open-circuit voltage is discussed in detail. We will also elaborate on the efficiency of dissociation and photocurrent generation from thermally relaxed CT states. Based on thermodynamical considerations and in the absence of nonradiative recombination, upper limits for the efficiency of organic solar cells based on donor–acceptor interfaces are derived and possible improvements and future research directions are indicated.
|
|
| 15. |
- Vandewal, Koen, et al.
(författare)
-
On the origin of the open-circuit voltage of polymer-fullerene solar cells
- 2009
-
Ingår i: NATURE MATERIALS. - : Springer Science and Business Media LLC. - 1476-1122 .- 1476-4660. ; 8:11, s. 904-909
-
Tidskriftsartikel (refereegranskat)abstract
- The increasing amount of research on solution-processable, organic donor-acceptor bulk heterojunction photovoltaic systems, based on blends of conjugated polymers and fullerenes has resulted in devices with an overall power-conversion efficiency of 6%. For the best devices, absorbed photon-to-electron quantum efficiencies approaching 100% have been shown. Besides the produced current, the overall efficiency depends critically on the generated photovoltage. Therefore, understanding and optimization of the open-circuit voltage (V-oc) of organic solar cells is of high importance. Here, we demonstrate that charge-transfer absorption and emission are shown to be related to each other and V-oc in accordance with the assumptions of the detailed balance and quasi-equilibrium theory. We underline the importance of the weak ground-state interaction between the polymer and the fullerene and we confirm that V-oc is determined by the formation of these states. Our work further suggests alternative pathways to improve V-oc of donor-acceptor devices.
|
|
| 16. |
- Vandewal, Koen, et al.
(författare)
-
Polarization anisotropy of charge transfer absorption and emission of aligned polymer: fullerene blend films
- 2012
-
Ingår i: Physical Review B. Condensed Matter and Materials Physics. - : American Physical Society. - 1098-0121 .- 1550-235X. ; 86:3, s. 035212-
-
Tidskriftsartikel (refereegranskat)abstract
- An improved understanding of the electronic structure of interfacial charge transfer (CT) states is of importance due to their crucial role in charge carrier generation and recombination in organic donor-acceptor (DA) solar cells. DA combinations with a small difference between the energy of the CT state (E-CT) and energy of the donor exciton (E-D*) are of special interest since energy losses due to electron transfer are minimized, resulting in an optimized open-circuit voltage. In that case, the CT state can be considered as a resonance mixture, containing character of a fully ionic state (D+ A(-)) and of the local polymer excited state (D* A). We show that the D* A contribution to the overall CT state wave function can be determined by measurements of the polarization anisotropy of CT absorption and emission of polymer: fullerene blends with aligned polymer chains. We study two donor polymers, P3HT and TQ1, blended with fullerene acceptors with different ionization potentials, allowing variation of the E-D* -E-CT difference. We find that, upon decreasing E-D* -E-CT, the local excitonic D* A character of the CT state increases, resulting in a decreased fraction of charge transferred and an increased transition dipole moment. For typical polymer: fullerene systems, this effect is expected to become detrimental for device performance if E-D* - E-CT andlt; 0.1 eV. This however, depends on the electronic coupling between D* A and D+ A(-), which we experimentally estimate to be similar to 6 meV for the TQ1: PCBM system.
|
|
| 17. |
- Vandewal, Koen, et al.
(författare)
-
Quantification of Quantum Efficiency and Energy Losses in Low Bandgap Polymer:Fullerene Solar Cells with High Open-Circuit Voltage
- 2012
-
Ingår i: Advanced Functional Materials. - : Wiley-VCH Verlag Berlin. - 1616-301X .- 1616-3028. ; 22:16, s. 3480-3490
-
Tidskriftsartikel (refereegranskat)abstract
- In organic solar cells based on polymer:fullerene blends, energy is lost due to electron transfer from polymer to fullerene. Minimizing the difference between the energy of the polymer exciton (ED*) and the energy of the charge transfer state (ECT) will optimize the open-circuit voltage (Voc). In this work, this energy loss ED*-ECT is measured directly via Fourier-transform photocurrent spectroscopy and electroluminescence measurements. Polymer:fullerene photovoltaic devices comprising two different isoindigo containing polymers: P3TI and PTI-1, are studied. Even though the chemical structures and the optical gaps of P3TI and PTI-1 are similar (1.4 eV1.5 eV), the optimized photovoltaic devices show large differences in Voc and internal quantum efficiency (IQE). For P3TI:PC71BM blends a ED*-ECT of similar to 0.1 eV, a Voc of 0.7 V and an IQE of 87% are found. For PTI-1:PC61BM blends an absence of sub-gap charge transfer absorption and emission bands is found, indicating almost no energy loss in the electron transfer step. Hence a higher Voc of 0.92 V, but low IQE of 45% is obtained. Morphological studies and field dependent photoluminescence quenching indicate that the lower IQE for the PTI-1 system is not due to a too coarse morphology, but is related to interfacial energetics. Losses between ECT and qVoc due to radiative and non-radiative recombination are quantified for both material systems, indicating that for the PTI-1:PC61BM material system, Voc can only be increased by decreasing the non-radiative recombination pathways. This work demonstrates the possibility of obtaining modestly high IQE values for material systems with a small energy offset (andlt;0.1 eV) and a high Voc.
|
|
| 18. |
- Vandewal, Koen, et al.
(författare)
-
Relating the open-circuit voltage to interface molecular properties of donor:acceptor bulk heterojunction solar cells
- 2010
-
Ingår i: PHYSICAL REVIEW B. - : American Physical Society. - 1098-0121. ; 81:12, s. 125204-
-
Tidskriftsartikel (refereegranskat)abstract
- The open-circuit voltage (V-oc) of polymer:fullerene bulk heterojunction solar cells is determined by the interfacial charge-transfer (CT) states between polymer and fullerene. Fourier-transform photocurrent spectroscopy and electroluminescence spectra of several polymer:fullerene blends are used to extract the relevant interfacial molecular parameters. An analytical expression linking these properties to V-oc is deduced and shown to be valid for photovoltaic devices comprising three commonly used conjugated polymers blended with the fullerene derivative [6,6]-phenyl-C61-butyric acid methyl ester (PCBM). V-oc is proportional to the energy of the CT states E-CT. The energetic loss q Delta V between E-CT and qV(oc) vanishes when approaching 0 K. It depends linearly on T and logarithmically on illumination intensity. Furthermore q Delta V can be reduced by decreasing the electronic coupling between polymer and fullerene or by reducing the nonradiative recombination rate. For the investigated devices we find a loss q Delta V of similar to 0.6 eV at room temperature and under solar illumination conditions, of which similar to 0.25 eV is due to radiative recombination via the CT state and similar to 0.35 eV is due to nonradiative recombination.
|
|
| 19. |
- Wang, Chuanfei, et al.
(författare)
-
Low Band Gap Polymer Solar Cells With Minimal Voltage Losses
- 2016
-
Ingår i: Advanced Energy Materials. - : Wiley. - 1614-6832 .- 1614-6840. ; 6:18
-
Tidskriftsartikel (refereegranskat)abstract
- One of the factors limiting the performance of organic solar cells (OSCs) is their large energy losses (E loss) in the conversion from photons to electrons, typically believed to be around 0.6 eV and often higher than those of inorganic solar cells. In this work, a novel low band gap polymer PIDTT-TID with a optical gap of 1.49 eV is synthesized and used as the donor combined with PC71BM in solar cells. These solar cells attain a good power conversion efficiency of 6.7% with a high open-circuit voltage of 1.0 V, leading to the E loss as low as 0.49 eV. A systematic study indicates that the driving force in this donor and acceptor system is sufficient for charge generation with the low E loss. This work pushes the minimal E loss of OSCs down to 0.49 eV, approaching the values of some inorganic and hybrid solar cells. It indicates the potential for further enhancement of the performance of OSCs by improving their V oc since the E loss can be minimized.
|
|
| 20. |
|
|
| 21. |
- Wang, Ergang, 1981, et al.
(författare)
-
An Easily Accessible Isoindigo-Based Polymer for High-Performance Polymer Solar Cells
- 2011
-
Ingår i: Journal of the American Chemical Society. - : American Chemical Society (ACS). - 1520-5126 .- 0002-7863. ; 133:36, s. 14244-14247
-
Tidskriftsartikel (refereegranskat)abstract
- A new, low-band-gap alternating copolymer consisting of terthiophene and isoindigo has been designed and synthesized. Solar cells based on this polymer and PC(71)BM show a power conversion efficiency of 6.3%, which is a record for polymer solar cells based on a polymer with an optical band gap below 1.5 eV. This work demonstrates the great potential of isoindigo moieties as electron-deficient units for building donor-acceptor-type polymers for high-performance polymer solar cells.
|
|
| 22. |
- Wang, Ergang, 1981, et al.
(författare)
-
Conformational Disorder Enhances Solubility and Photovoltaic Performance of a Thiophene–Quinoxaline Copolymer
- 2013
-
Ingår i: Advanced Energy Materials. - : Wiley. - 1614-6840 .- 1614-6832. ; 3:6, s. 806-814
-
Tidskriftsartikel (refereegranskat)abstract
- The side-chain architecture of alternating copolymers based on thiophene and quinoxaline (TQ) is found to strongly influence the solubility and photovoltaic performance. In particular, TQ polymers with different linear or branched alkyloxy-phenyl side chains on the quinoxaline unit are compared. Attaching the linear alkyloxy side-chain segment at the meta- instead of the para-position of the phenyl ring reduces the planarity of the backbone as well as the ability to order. However, the delocalisation across the backbone is not affected, which permits the design of high-performance TQ polymers that do not aggregate in solution. The use of branched meta-(2-ethylhexyl)oxy-phenyl side-chains results in a TQ polymer with an intermediate degree of order. The reduced tendency for aggregation of TQ polymers with linear meta-alkyloxy-phenyl persists in the solid state. As a result, it is possible to avoid the decrease in charge-transfer state energy that is observed for bulk-heterojunction blends of more ordered TQ polymers and fullerenes. The associated gain in open-circuit voltage of disordered TQ:fullerene solar cells, accompanied by a higher short-circuit current density, leads to a higher power conversion efficiency overall. Thus, in contrast to other donor polymers, for TQ polymers there is no need to compromise between solubility and photovoltaic performance.
|
|
| 23. |
- Wang, Yuming, et al.
(författare)
-
Optical Gaps of Organic Solar Cells as a Reference for Comparing Voltage Losses
- 2018
-
Ingår i: Advanced Energy Materials. - : WILEY-V C H VERLAG GMBH. - 1614-6832 .- 1614-6840. ; 8:28
-
Tidskriftsartikel (refereegranskat)abstract
- The voltage loss, determined by the difference between the optical gap (E-g) and the open-circuit voltage (V-OC), is one of the most important parameters determining the performance of organic solar cells (OSCs). However, the variety of different methods used to determine E-g makes it hard to fairly compare voltages losses among different material systems. In this paper, the authors discuss and compare various E-g determination methods and show how they affect the detailed calculation of voltage losses, as well as predictions of the maximum achievable power conversion efficiency. The aim of this paper is to make it possible for the OSC community to compare voltage losses in a consistent and reasonable way. It is found that the voltage losses for strongly absorbed photons in state-of-the-art OSCs are not much less than 0.6 V, which still must be decreased to further enhance efficiency.
|
|
| 24. |
- Wang, Yuming, et al.
(författare)
-
Origins of the open-circuit voltage in ternary organic solar cells and design rules for minimized voltage losses
- 2023
-
Ingår i: Nature Energy. - : NATURE PORTFOLIO. - 2058-7546. ; 8:9, s. 978-988
-
Tidskriftsartikel (refereegranskat)abstract
- The power conversion efficiency of ternary organic solar cells (TOSCs), consisting of one host binary blend and one guest component, remains limited by large voltage losses. The fundamental understanding of the open-circuit voltage (V-OC) in TOSCs is controversial, limiting rational design of the guest component. In this study, we systematically investigate how the guest component affects the radiative and non-radiative related parts of V-OC of a series of TOSCs using the detailed balanced principle. We highlight that the thermal population of charge-transfer and local exciton states provided by the guest binary blend (that is, the guest-component-based binary blend) has a significant influence on the non-radiative voltage losses. Ultimately, we provide two design rules for enhancing the V-OC in TOSCs: high emission yield for the guest binary blend and similar charge-transfer-state energies for host/guest binary blends; high miscibility of the guest component with the low gap component in the host binary blend. The performance of ternary organic solar cells is limited by voltage losses. Using the detailed balance principle, Wang et al. show how the third component of the blend affects the open-circuit voltage and delineate molecular design rules.
|
|
| 25. |
- Zhang, Fengling, et al.
(författare)
-
Development of polymer-fullerene solar cells
- 2016
-
Ingår i: NATIONAL SCIENCE REVIEW. - : OXFORD UNIV PRESS. - 2095-5138 .- 2053-714X. ; 3:2, s. 222-239
-
Forskningsöversikt (refereegranskat)abstract
- Global efforts and synergetic interdisciplinary collaborations on solution-processed bulk-heterojunction polymer solar cells (PSCs or OPVs) made power conversion efficiencies over 10% possible. The rapid progress of the field is credited to the synthesis of a large number of novel polymers with specially tunable optoelectronic properties, a better control over the nano-morphology of photoactive blend layers, the introduction of various effective interfacial layers, new device architectures and a deeper understanding of device physics. We will review the pioneering materials for polymer-fullerene solar cells and trace the progress of concepts driving their development. We discuss the evolution of morphology control, interfacial layers and device structures fully exploring the potential of photoactive materials. In order to guide a further increase in power conversion efficiency of OPV, the current understanding of the process of free charge carrier generation and the origin of the photovoltage is summarized followed by a perspective on how to overcome the limitations for industrializing PSCs.
|
|
