| 1. |
- Fan, Qunping, 1989, et al.
(author)
-
High-performance all-polymer solar cells enabled by a novel low bandgap non-fully conjugated polymer acceptor
- 2021
-
In: Science in China Series B. - : Springer Nature. - 1674-7291 .- 1869-1870. ; 64, s. 1380-1388
-
Journal article (peer-reviewed)abstract
- Anon-fully conjugated polymer as a new class of acceptor materials has shown some advantages over its small molecular counterpart when used in photoactive layers for all-polymer solar cells (all-PSCs), despite a low power conversion efficiency (PCE) caused by its narrow absorption spectra. Herein, a novel non-fully conjugated polymer acceptor PFY-2TS with a low bandgap of similar to 1.40 eV was developed, via polymerizing a large pi-fused small molecule acceptor (SMA) building block (namely YBO) with a non-conjugated thioalkyl linkage. Compared with its precursor YBO, PFY-2TS retains a similar low bandgap but a higher LUMO level. Moreover, compared with the structural analog of YBO-based fully conjugated polymer acceptor PFY-DTC, PFY-2TS shows similar absorption spectrum and electron mobility, but significantly different molecular crystallinity and aggregation properties, which results in optimal blend morphology with a polymer donor PBDB-T and better device physical processes in all-PSCs. As a result, PFY-2TS-based all-PSCs achieved a PCE of 12.31% with a small energy loss of 0.56 eV enabled by the reduced non-radiative energy loss (0.24 eV), which is better than that of 11.08% for the PFY-DTC-based ones. Our work clearly demonstrated that non-fully conjugated polymers as a new class of acceptor materials are very promising for the development of high-performance all-PSCs.
|
|
| 2. |
- Li, Zaifang, et al.
(author)
-
A Free-Standing High-Output Power Density Thermoelectric Device Based on Structure-Ordered PEDOT:PSS
- 2018
-
In: Advanced Electronic Materials. - : Wiley-VCH Verlagsgesellschaft. - 2199-160X. ; 4:2
-
Journal article (peer-reviewed)abstract
- A free-standing high-output power density polymeric thermoelectric (TE) device is realized based on a highly conductive (approximate to 2500 S cm(-1)) structure-ordered poly(3,4-ethylenedioxythiophene):polystyrene sulfonate film (denoted as FS-PEDOT:PSS) with a Seebeck coefficient of 20.6 mu V K-1, an in-plane thermal conductivity of 0.64 W m(-1) K-1, and a peak power factor of 107 mu W K-2 m(-1) at room temperature. Under a small temperature gradient of 29 K, the TE device demonstrates a maximum output power density of 99 +/- 18.7 mu W cm(-2), which is the highest value achieved in pristine PEDOT:PSS based TE devices. In addition, a fivefold output power is demonstrated by series connecting five devices into a flexible thermoelectric module. The simplicity of assembling the films into flexible thermoelectric modules, the low out-of-plane thermal conductivity of 0.27 W m(-1) K-1, and free-standing feature indicates the potential to integrate the FS-PEDOT:PSS TE modules with textiles to power wearable electronics by harvesting human bodys heat. In addition to the high power factor, the high thermal stability of the FS-PEDOT:PSS films up to 250 degrees C is confirmed by in situ temperature-dependent X-ray diffraction and grazing incident wide angle X-ray scattering, which makes the FS-PEDOT:PSS films promising candidates for thermoelectric applications.
|
|
| 3. |
- Liu, Tao, et al.
(author)
-
16% efficiency all-polymer organic solar cells enabled by a finely tuned morphology via the design of ternary blend
- 2021
-
In: Joule. - : CELL PRESS. - 2542-4351. ; 5:4, s. 914-930
-
Journal article (peer-reviewed)abstract
- A SUMMARY There is an urgent demand for all-polymer organic solar cells (AP-OSCs) to gain higher efficiency. Here, we successfully improve the performance to 16.09% by introducing a small amount of BN-T, a B <- N-type polymer acceptor, into the PM6:PY-IT blend. It has been found that BN-T makes the active layer, based on the PM6:PY-IT:BN-T ternary blend, more crystalline but meanwhile slightly reduces the phase separation, leading to enhancement of both exciton harvesting and charge transport. From a thermodynamic viewpoint, BN-T prefers to reside between PM6 and PY-IT, and the fraction of this fine-tunes the morphology. Besides, a significantly reduced nonradiative energy loss occurs in the ternary blend, along with the coexistence of energy and charge transfer between the two acceptors. The progressive performance facilitated by these improved properties demonstrates that AP-OSCs can possibly comparably efficient with those based on small molecule acceptors, further enhancing the competitiveness of this device type.
|
|
| 4. |
- Luo, Zhenghui, et al.
(author)
-
Fine-Tuning Energy Levels via Asymmetric End Groups Enables Polymer Solar Cells with Efficiencies over 17%
- 2020
-
In: Joule. - : CELL PRESS. - 2542-4351. ; 4:6, s. 1236-1247
-
Journal article (peer-reviewed)abstract
- Generally, it is important to fine-tune the energy levels of donor and acceptor materials in the field of polymer solar cell (PSCs) to achieve a minimal highest occupied molecular orbital (HOMO) energy offset, which yet is still sufficient for charge separation. Based on the high-performance small-molecule acceptor (SMA) of BTP-4F, we modified the end groups of BTP-4F from IC-2F to CPTCN-Cl. It was found that when both end groups were substituted by CPTCN-Cl, the energy level upshift was too large that caused unfavorable energetic alignment, thus poor device performance. By using the strategy of asymmetric end groups, we were able to achieve near optimal energy level match, resulting in higher open-circuit voltage (V-OC) and power conversion efficiency (PCE) compared with those given by the PM6:BTP-4F system. Our strategy can be useful and potentially applied to othermaterial systems for maximizing efficiency of non-fullerene PSCs.
|
|
| 5. |
- Ma, Ruijie, et al.
(author)
-
Adding a Third Component with Reduced Miscibility and Higher LUMO Level Enables Efficient Ternary Organic Solar Cells
- 2020
-
In: ACS Energy Letters. - : American Chemical Society (ACS). - 2380-8195. ; 5:8, s. 2711-2720
-
Journal article (peer-reviewed)abstract
- It is widely known that the miscibility between donor and acceptor is a crucial factor that affects the morphology and thus device performance of nonfullerene organic solar cells (OSCs). In this Letter, we show that incorporating a third component with lower miscibility and higher lowest unoccupied molecular orbital (LUMO) level into the state-of-the-art PM6:Y6 system can significantly enhance the performance of devices. The best results of the ternary devices are achieved by adding a small molecular acceptor named ITCPTC (similar to 5% w/w), which significantly improves the power conversion efficiency (PCE) of the host system from 16.44% to 17.42%. The higher LUMO of the third component increases the open-circuit voltage (V-oc), while the low miscibility enlarges the domains and leads to improved short-circuit current density (J(sc)) and fill factor (FF). The efficacy of this strategy is supported by using other nonfullerene third components including an asymmetric small molecule (N7IT) and a polymer acceptor (PF2-DTC), which play the same role as ITCPTC and boost the PCEs to 16.96% and 17.04%, respectively. Our approach can be potentially applied to a wide range of OSC material systems and should facilitate the development of the OSC field.
|
|
| 6. |
- Ma, Ruijie, et al.
(author)
-
All-polymer solar cells with over 16% efficiency and enhanced stability enabled by compatible solvent and polymer additives
- 2022
-
In: Aggregate. - : Wiley. - 2692-4560 .- 2766-8541. ; 3:3
-
Journal article (peer-reviewed)abstract
- Considering the robust and stable nature of the active layers, advancing the power conversion efficiency (PCE) has long been the priority for all-polymer solar cells (all-PSCs). Despite the recent surge of PCE, the photovoltaic parameters of the state-of-the-art all-PSC still lag those of the polymer:small molecule-based devices. To compete with the counterparts, judicious modulation of the morphology and thus the device electrical properties are needed. It is difficult to improve all the parameters concurrently for the all-PSCs with advanced efficiency, and one increase is typically accompanied by the drop of the other(s). In this work, with the aids of the solvent additive (1-chloronaphthalene) and the n-type polymer additive (N2200), we can fine-tune the morphology of the active layer and demonstrate a 16.04% efficient all-PSC based on the PM6:PY-IT active layer. The grazing incidence wide-angle X-ray scattering measurements show that the shape of the crystallites can be altered, and the reshaped crystallites lead to enhanced and more balanced charge transport, reduced recombination, and suppressed energy loss, which lead to concurrently improved and device efficiency and stability.
|
|
| 7. |
- Wang, Chuan Fei, et al.
(author)
-
Diluted Organic Semiconductors in Photovoltaics
- 2020
-
In: Solar RRL. - : WILEY-V C H VERLAG GMBH. - 2367-198X. ; 4:9
-
Journal article (peer-reviewed)abstract
- Incorporation of insulating polymers or molecules into organic semiconductor films, creating so-called diluted organic semiconductors, has been successfully used both in organic field-effect transistors and organic light-emitting diodes to reduce sensitivity to charge traps. However, application of this strategy in organic photovoltaics is challenging due to the complex requirements on the light-absorbing blend layer. Herein, diluted donor-acceptor-insulator ternary organic solar cells are developed to improve mobility and decrease radiative and nonradiative recombination in the active layer. In addition, both thermal and environmental stability of the diluted ternary solar cells are enhanced. Finally, the diluted semiconductor approach enables large-area solar cells to be fabricated where the loss in power density upon cell area upscaling is five times lower than for the equivalent binary cells.
|
|
| 8. |
- Xia, Xinxin, et al.
(author)
-
Revealing the crystalline packing structure of Y6 in the active layer of organic solar cells: the critical role of solvent additives
- 2023
-
In: Journal of Materials Chemistry A. - : ROYAL SOC CHEMISTRY. - 2050-7488 .- 2050-7496. ; 11:40, s. 21895-21907
-
Journal article (refereegranskat)abstract
- The bulk heterojunction (BHJ) morphology of photovoltaic materials is crucial to the fundamental optoelectronic properties of organic solar cells (OSCs). However, in the photoactive layer, the intrinsic crystalline packing structure of Y6, currently the hallmark molecule among Y-series non-fullerene acceptors (NFAs), has not been unambiguously determined. Here, employing grazing-incidence wide-angle X-ray scattering (GIWAXS), we managed to uncover the intrinsic crystalline packing structure of Y6 in the BHJ active layer of OSCs, which is found to be different from its single-crystal structure reported previously. Moreover, we find that solvent additive 1-chloronaphthalene (CN) can induce highly ordered packing of Y6 in BHJ thin films. With the help of atomistic molecular dynamics simulations, it is revealed that pi-pi interactions generally exist between naphthalene derivatives and IC terminals of Y6 analogues, which would essentially improve their long-range ordering. Our work reveals the intrinsic crystalline packing structure of Y6 in the BHJ active layer as well as its crystallization mechanism in thin films, thus providing direct correlations between this crystalline packing and the device characteristics and photophysical properties.
|
|
| 9. |
- Yao, Lei, et al.
(författare)
-
Atmospheric new particle formation from sulfuric acid and amines in a Chinese megacity
- 2018
-
Ingår i: Science. - : American Association for the Advancement of Science (AAAS). - 0036-8075 .- 1095-9203. ; 361:6399, s. 278-281
-
Tidskriftsartikel (refereegranskat)abstract
- Atmospheric new particle formation (NPF) is an important global phenomenon that is nevertheless sensitive to ambient conditions. According to both observation and theoretical arguments, NPF usually requires a relatively high sulfuric acid (H2SO4) concentration to promote the formation of new particles and a low preexisting aerosol loading to minimize the sink of new particles. We investigated NPF in Shanghai and were able to observe both precursor vapors (H2SO4) and initial clusters at a molecular level in a megacity. High NPF rates were observed to coincide with several familiar markers suggestive of H2SO4-dimethylamine (DMA)water (H2O) nucleation, including sulfuric acid dimers and H2SO4-DMA clusters. In a cluster kinetics simulation, the observed concentration of sulfuric acid was high enough to explain the particle growth to similar to 3 nanometers under the very high condensation sink, whereas the subsequent higher growth rate beyond this size is believed to result fromthe added contribution of condensing organic species. These findings will help in understanding urban NPF and its air quality and climate effects, as well as in formulating policies to mitigate secondary particle formation in China.
|
|
| 10. |
- Yu, Han, et al.
(författare)
-
Fluorinated End Group Enables High-Performance All-Polymer Solar Cells with Near-Infrared Absorption and Enhanced Device Efficiency over 14%
- 2021
-
Ingår i: Advanced Energy Materials. - : WILEY-V C H VERLAG GMBH. - 1614-6832 .- 1614-6840. ; 11:4
-
Tidskriftsartikel (refereegranskat)abstract
- Fluorination of end groups has been a great success in developing efficient small molecule acceptors. However, this strategy has not been applied to the development of polymer acceptors. Here, a dihalogenated end group modified by fluorine and bromine atoms simultaneously, namely IC-FBr, is first developed, then employed to construct a new polymer acceptor (named PYF-T) for all-polymer solar cells (all-PSCs). In comparison with its non-fluorinated counterpart (PY-T), PYF-T exhibits stronger and red-shifted absorption spectra, stronger molecular packing and higher electron mobility. Meanwhile, the fluorination on the end groups down-shifts the energy levels of PYF-T, which matches better with the donor polymer PM6, leading to efficient charge transfer and small voltage loss. As a result, an all-PSC based on PM6:PYF-T yields a higher power conversion efficiency (PCE) of 14.1% than that of PM6:PY-T (11.1%), which is among the highest values for all-PSCs reported to date. This work demonstrates the effectiveness of fluorination of end-groups in designing high-performance polymer acceptors, which paves the way toward developing more efficient and stable all-PSCs.
|
|
