| 11. |
|
|
| 12. |
- Abat, E., et al.
(författare)
-
The ATLAS Transition Radiation Tracker (TRT) proportional drift tube: design and performance
- 2008
-
Ingår i: Journal of Instrumentation. - 1748-0221. ; 3:2
-
Tidskriftsartikel (refereegranskat)abstract
- A straw proportional counter is the basic element of the ATLAS Transition Radiation Tracker (TRT). Its detailed properties as well as the main properties of a few TRT operating gas mixtures are described. Particular attention is paid to straw tube performance in high radiation conditions and to its operational stability.
|
|
| 13. |
- Abat, E., et al.
(författare)
-
The ATLAS TRT barrel detector
- 2008
-
Ingår i: Journal of Instrumentation. - 1748-0221. ; 3
-
Tidskriftsartikel (refereegranskat)abstract
- The ATLAS TRT barrel is a tracking drift chamber using 52,544 individual tubular drift tubes. It is one part of the ATLAS Inner Detector, which consists of three sub-systems: the pixel detector spanning the radius range 4 to 20 cm, the semiconductor tracker (SCT) from 30 to 52 cm, and the transition radiation tracker ( TRT) from 56 to 108 cm. The TRT barrel covers the central pseudo-rapidity region |eta| < 1, while the TRT endcaps cover the forward and backward eta regions. These TRT systems provide a combination of continuous tracking with many measurements in individual drift tubes ( or straws) and of electron identification based on transition radiation from fibers or foils interleaved between the straws themselves. This paper describes the recently-completed construction of the TRT Barrel detector, including the quality control procedures used in the fabrication of the detector.
|
|
| 14. |
- Abat, E., et al.
(författare)
-
The ATLAS TRT electronics
- 2008
-
Ingår i: Journal of Instrumentation. - 1748-0221. ; 3:6
-
Tidskriftsartikel (refereegranskat)abstract
- The ATLAS inner detector consists of three sub-systems: the pixel detector spanning the radius range 4cm-20cm, the semiconductor tracker at radii from 30 to 52 cm, and the transition radiation tracker (TRT), tracking from 56 to 107 cm. The TRT provides a combination of continuous tracking with many projective measurements based on individual drift tubes (or straws) and of electron identification based on transition radiation from fibres or foils interleaved between the straws themselves. This paper describes the on and off detector electronics for the TRT as well as the TRT portion of the data acquisition (DAQ) system.
|
|
| 15. |
- Abat, E., et al.
(författare)
-
The ATLAS TRT end-cap detectors
- 2008
-
Ingår i: Journal of Instrumentation. - 1748-0221. ; 3
-
Tidskriftsartikel (refereegranskat)abstract
- The ATLAS TRT end-cap is a tracking drift chamber using 245,760 individual tubular drift tubes. It is a part of the TRT tracker which consist of the barrel and two end-caps. The TRT end-caps cover the forward and backward pseudo-rapidity region 1.0 < vertical bar eta vertical bar < 2.0, while the TRT barrel central eta region vertical bar eta vertical bar < 1.0. The TRT system provides a combination of continuous tracking with many measurements in individual drift tubes ( or straws) and of electron identification based on transition radiation from fibers or foils interleaved between the straws themselves. Along with other two sub-systems, namely the Pixel detector and Semi Conductor Tracker (SCT), the TRT constitutes the ATLAS Inner Detector. This paper describes the recently completed and installed TRT end-cap detectors, their design, assembly, integration and the acceptance tests applied during the construction.
|
|
| 16. |
|
|
| 17. |
- Mindur, B, et al.
(författare)
-
Gas gain stabilisation in the ATLAS TRT detector
- 2016
-
Ingår i: Journal of Instrumentation. - 1748-0221. ; 11:4
-
Tidskriftsartikel (refereegranskat)abstract
- The ATLAS (one of two general purpose detectors at the LHC) Transition Radiation Tracker (TRT) is the outermost of the three tracking subsystems of the ATLAS Inner Detector. It is a large straw-based detector and contains about 350,000 electronics channels. The performance of the TRT as tracking and particularly particle identification detector strongly depends on stability of the operation parameters with most important parameter being the gas gain which must be kept constant across the detector volume. The gas gain in the straws can vary significantly with atmospheric pressure, temperature, and gas mixture composition changes. This paper presents a concept of the gas gain stabilisation in the TRT and describes in detail the Gas Gain Stabilisation System (GGSS) integrated into the Detector Control System (DCS). Operation stability of the GGSS during Run-1 is demonstrated.
|
|
| 18. |
|
|
| 19. |
|
|
| 20. |
- Cwetanski, P, et al.
(författare)
-
Acceptance tests and criteria of the ATLAS transition radiation tracker
- 2005
-
Ingår i: IEEE Transactions on Nuclear Science. - 0018-9499. ; 52:6, s. 2911-2916
-
Tidskriftsartikel (refereegranskat)abstract
- The Transition Radiation Tracker (TRT) sits at the outermost part of the ATLAS Inner Detector, encasing the Pixel Detector and the Semi-Conductor Tracker (SCT). The TRT combines charged particle track reconstruction with electron identification capability. This is achieved by layers of xenonfilled straw tubes with periodic radiator foils or fibers providing TR photon emission. The design and choice of materials have been optimized to cope with the harsh operating conditions at the LHC, which are expected to lead to an accumulated radiation dose of 10 Mrad and a neutron fluence of up to 2 . 10(14) n/cm(2) after ten years of operation. The TRT comprises a barrel containing 52 000 axial straws and two end-cap parts with 320 000 radial straws. The total of 420 000 electronic channels (two channels per barrel straw) allows continuous tracking with many projective measurements (more than 30 straw hits per track). The assembly of the barrel modules in the US has recently been completed, while the end-cap wheel construction in Russia has reached the 50% mark. After testing at the production sites and shipment to CERN, all modules and wheels undergo a series of quality and conformity measurements. These acceptance tests survey dimensions, wire tension, gas-tightness, high-voltage stability and gas-gain uniformity along each individual straw. This paper gives details on the acceptance criteria and measurement methods. An overview of the most important results obtained to-date is also given.
|
|
