| 1. |
- Abel, I, et al.
(författare)
-
Overview of the JET results with the ITER-like wall
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Tidskriftsartikel (refereegranskat)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 2. |
- Romanelli, F, et al.
(författare)
-
Overview of the JET results
- 2011
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Tidskriftsartikel (refereegranskat)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
| 3. |
- Litnovsky, A., et al.
(författare)
-
Overview of material migration and mixing, fuel retention and cleaning of ITER-like castellated structures in TEXTOR
- 2011
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 415:1, s. S289-S292
-
Tidskriftsartikel (refereegranskat)abstract
- Plasma-facing components (PFCs) in ITER will be castellated by splitting them into small-size blocks to maintain the thermo-mechanical stability. However, there are concerns in particular on retention of codeposited radioactive fuel in the gaps. An R&D program is underway in TEXTOR addressing this acute issue of castellation. Material migration and fuel inventory are investigated using long- and short-term discharge-resolved experiments with castellated structures in TEXTOR. Significant impurity transport to the gaps was detected and results were in part quantitatively reproduced with 3D-GAPS code. Deposits containing up to 70 at.% of tungsten on the gap areas closest to the plasma were detected in recent experiments. Deposition in the gaps accompanied by metal mixing demand for development of effective cleaning techniques. In experiments with ITER-like castellation, the gaps were cleaned from carbonaceous deposits using oxygen plasmas at 350 degrees C. This contribution contains an overview of experimental and modeling results along with recommendations for PFCs in ITER.
|
|
| 4. |
- Tsitrone, E., et al.
(författare)
-
Multi machine scaling of fuel retention in 4 carbon dominated tokamaks
- 2011
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 415:1, s. S735-S739
-
Tidskriftsartikel (refereegranskat)abstract
- In order to benchmark predictions for the in vessel tritium inventory in ITER, a survey of fuel retention measured in 4 carbon dominated tokamaks (TEXTOR, ASDEX Upgrade in the 2002-2003 carbon configuration, Tore Supra and JET) was performed, showing retention rates from similar to 1 g D/h in TEXTOR (L mode, limiter machine) up to similar to 6-12 g D/h in AUG (H mode, divertor machine). A simple scaling used for ITER predictions is applied for comparison with experimental values: (1) estimate of wall fluxes, (2) estimate of the gross carbon erosion, (3) estimate of the net erosion/redeposition assuming a redeposition fraction and (4) estimate of the retention rate using D/C ratio scalings. The validity of each step is discussed, showing that this approach yields the right order of magnitude, but tends to underestimate the experimental values unless a high wall flux, a low local redeposition fraction and/or a high D/C ratio are used.
|
|
| 5. |
- Litnovsky, A., et al.
(författare)
-
Dust investigations in TEXTOR : Impact of dust on plasma-wall interactions and on plasma performance
- 2013
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 438:Suppl., s. S126-S132
-
Tidskriftsartikel (refereegranskat)abstract
- Dust will have severe impact on ITER performance since the accumulation of tritium in dust represents a safety issue, a possible reaction of dust with air and steam imposes an explosion hazard and the penetration of dust in core plasmas may degrade plasma performance by increasing radiative losses. Investigations were performed in TEXTOR where known amounts of pre-characterized carbon, diamond and tungsten dust were mobilized into plasmas using special dust holders. Mobilization of dust changed a balance between plasma-surface interactions processes, significantly increasing net deposition. Immediately after launch dust was dominating both core and edge plasma parameters. Remarkably, in about 100 ms after the launch, the effect of dust on edge and core plasma parameters was vanished: no increase of carbon and tungsten concentrations in the core plasmas was detected suggesting a prompt transport of dust to the nearby plasma-facing components without further residence in the plasma.
|
|
| 6. |
- Petersson, Per, et al.
(författare)
-
Overview of nitrogen-15 application as a tracer gas for material migration and retention studies in tokamaks
- 2014
-
Ingår i: Physica Scripta. - : IOP Publishing. - 0031-8949 .- 1402-4896. ; T159, s. 014042-
-
Tidskriftsartikel (refereegranskat)abstract
- Experimental and analytical procedures related to the application of nitrogen-15 isotope for material migration studies have been developed and used for tracer experiments in the TEXTOR and ASDEX-Upgrade tokamaks in order to assess the retention of nitrogen in plasma-facing components made of graphite and tungsten. The surface study was performed by time-of-flight heavy ion elastic recoil detection analysis and by means of nuclear reaction analysis based on the N-15(p, gamma alpha)C-12 process. In both tokamaks nitrogen retention has exceeded 10% of the injected gas. In ASDEX-Upgrade the largest fraction of N-15 has been detected on protruding parts near the injection port, while around 4% has been found in the divertor. The ASDEX-Upgrade results have also been modeled. Helium trapping has been measured in deposits containing tungsten and nitrogen.
|
|
| 7. |
- Rubel, Marek, et al.
(författare)
-
Tungsten migration studies by controlled injection of volatile compounds
- 2013
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 438, s. S170-S174
-
Tidskriftsartikel (refereegranskat)abstract
- Volatile tungsten hexa-fluoride was locally injected into the TEXTOR tokamak as a marker for material migration studies. The injection was accompanied by puffing N-15 rare isotope as a nitrogen tracer in discharges with edge cooling by impurity seeding. The objective was to assess material balance by qualitative and quantitative determination of a global and local deposition pattern, material mixing effects and fluorine residence in plasma-facing components. Spectroscopy and ex situ ion beam analysis techniques were used. Tungsten was detected on all types of limiter tiles and short-term probes retrieved from the vessel. Over 80% of the injected W was identified. The largest tungsten concentration, 1 x 10(18) cm(-2), was in the vicinity of the gas inlet. Co-deposits contained tungsten and a mix of light isotopes: H, D, He-4, B-10, B-11, C-12, C-13, N-14, N-15, O-16 and small quantities of F-19 thus showing that both He and nitrogen are trapped following wall conditioning (He glow) and edge cooling.
|
|
| 8. |
|
|
| 9. |
- Wauters, T., et al.
(författare)
-
Hydrogen ion cyclotron wall conditioning for fuel removal on TEXTOR and ASDEX upgrade
- 2012
-
Ingår i: 39th EPS Conference on Plasma Physics 2012, EPS 2012 and the 16th International Congress on Plasma Physics. - 9781622769810 ; , s. 1378-1381
-
Konferensbidrag (refereegranskat)abstract
- Ion Cyclotron Wall Conditioning (ICWC), applicable in presence of the toroidal magnetic field, is envisaged in ITER to recover from disruptions, leaks and torus vents, for recycling control and for fuel removal. Various experiments on different devices as well as modeling efforts are advancing to consolidate this technique. This contribution focuses on a selection of recent hydrogen ICWC experiments on ASDEX Upgrade and TEXTOR. The ASDEX Upgrade experiment aimed at comparing isotopic exchange efficiencies previously obtained on Carbon devices to the ITER relevant Tungsten wall. The experiment on TEXTOR aimed at assessing the performance of H2-ICWC for codeposited layer removal. The latter being a particular important fuel removal aspect since it is predicted that a major part of tritium in-vessel inventory build-up on ITER will be due to the formation of tritium rich codeposited layers.
|
|
| 10. |
- Wauters, T., et al.
(författare)
-
Self-consistent application of ion cyclotron wall conditioning for co-deposited layer removal and recovery of tokamak operation on TEXTOR
- 2013
-
Ingår i: Nuclear Fusion. - : Institute of Physics (IOP). - 0029-5515 .- 1741-4326. ; 53:12, s. 123001-
-
Tidskriftsartikel (refereegranskat)abstract
- This paper presents a demonstration experiment of ion cyclotron wall conditioning (ICWC) on TEXTOR covering all ITER wall conditioning aims and discusses the implications for ITER. O-2/He-ICWC applied to erode carbon co-deposits removed 6.6x10(21) C-atoms (39 pulses, 158 s cumulated discharge time). Large oxygen retention (71% of injected oxygen) prevented subsequent ohmic discharge initiation. Plasma operation was recovered by a 1h47 multi-pulse D-2-ICWC procedure including pumping time between pulses with duty cycle of 2 s/20 s, cleaning the vessel from oxygen impurities, followed by a 23 min He-ICWC procedure (2 s/20 s), applied to desaturate the deuterium-loaded walls. A stable ohmic discharge was established on the first attempt right after the recovery procedure. The discharges showed improved density control and only slightly increased oxygen characteristic radiation levels (1-1.5 times). After the recovery procedure 36% of the injected O-atoms remained retained in the vessel, derived from mass spectrometry measurements. This amount is in the estimated range for storage in remote areas obtained from surface analysis of locally exposed samples. The removed amount of oxygen by D-2 and He-ICWC obtained from mass spectrometry corresponds to the retention in plasma-wetted areas estimated by surface analysis. It is concluded that most of the removed oxygen stems from plasma-wetted areas while shadowed areas, e. g. behind poloidal limiters, may feature net retention of the discharge gas. On ITER, designed with a shaped first wall, the ICWC plasma-wetted area will approach the total surface area, reducing consequently the retention in remote areas. A tentative extrapolation of the carbon removal on TEXTOR to tritium removal from co-deposits on ITER in the 39 x 4 s O-2/He-ICWC discharges, including pumping time between the RF pulses, corresponds on ITER to a tritium removal in the order of the estimated retention per 400 s DT-burn (140-500 mgT (Shimada and Pitts 2011 J. Nucl. Mater. 415 S1013-6)).
|
|
