1. |
- Duan, Shanghong, 1992, et al.
(författare)
-
Determination of transverse and shear moduli of single carbon fibres
- 2020
-
Ingår i: Carbon. - : Elsevier BV. - 0008-6223 .- 1873-3891. ; 158C, s. 772-782
-
Tidskriftsartikel (refereegranskat)abstract
- Carbon fibres are extensively used for their high specific mechanical properties. Exploiting their high axial stiffness and strength, they are employed to reinforce polymer matrix materials in advanced composites. However, carbon fibres are not isotropic. Data of the elastic properties in the other directions of the fibres are still largely unknown. Furthermore, standardised methods to characterise these properties are lacking. In the present work, we propose a methodology to determine the transverse and shear moduli of single carbon fibres. An experimental procedure is developed to fabricate high-quality, flat fibre cross-sections in both longitudinal and transverse directions using Focused Ion Beam, which gives full control of the specimen geometry. Indentation modulus on those surfaces are obtained using both Atomic Force Microscopy (AFM) and nanoindentation tests. Hysteresis was found to occur in the nanoindentation tests. The hysteresis response was due to nano-buckling and reversible shear deformation of the carbon crystals. For this reason, indentation tests using AFM is recommended. From the AFM indentation tests the transverse and shear moduli of three different carbon fibres (IMS65, T800 and M60J) are successfully determined.
|
|
2. |
- Johansen, Marcus, 1994, et al.
(författare)
-
Mapping nitrogen heteroatoms in carbon fibres using atom probe tomography and photoelectron spectroscopy
- 2021
-
Ingår i: Carbon. - : Elsevier BV. - 0008-6223. ; 179, s. 20-27
-
Tidskriftsartikel (refereegranskat)abstract
- Carbon fibres show great potential as multifunctional negative electrode for novel structural battery composites – a rechargeable electrochemical cell with structural function. The electrochemical performance of carbon materials can be enhanced with nitrogen heteroatoms, which conveniently are inherent in polyacrylonitrile (PAN)-based carbon fibres. However, it is not fully understood how the electrochemical performance is governed by microstructure and composition of the carbon fibres, particularly the distribution and chemical states of nitrogen heteroatoms. Here we reveal the atom-by-atom three-dimensional spatial distribution and the chemical states of nitrogen in three PAN-carbon fibre types (M60J, T800 and IMS65), using atom probe tomography (APT) and synchrotron hard X-ray photoelectron spectroscopy (HAXPES), and correlate the results to electrochemical performance. The findings pave the way for future tailoring of carbon fibre microstructure for multifunctional applications.
|
|
3. |
- Johansen, Marcus, 1994
(författare)
-
Microstructure of Carbon Fibres for Multifunctional Composites: 3D Distribution and Configuration of Atoms
- 2021
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Lightweight energy storage is a must for increased driving range of electric vehicles. “Mass-less” energy storage can be achieved by directly storing energy in structural components. In such multifunctional devices called structural composite batteries, carbon fibres carry mechanical load and simultaneously act as negative battery electrode by hosting lithium ions in its microstructure. Little is known of how the microstructure of carbon fibres is optimised for multifunctionality, and deeper understanding of the configuration and the distribution of atoms in carbon fibres is needed. Here synchrotron hard X-ray photoelectron spectroscopy and atom probe tomography are used to reveal the chemical states and three-dimensional distribution of atoms in commercial carbon fibres. This thesis presents the first ever guide for how to perform atom probe tomography on carbon fibres, and the first ever three-dimensional atomic reconstruction of a carbon fibre. The results show that the chemical states and distribution of nitrogen heteroatoms in carbon fibres affect the electrochemical performance of the fibres. Carbon fibres performed electrochemically better with higher amount of nitrogen with pyridinic and pyrrolic configurations. Additionally, the nitrogen concentration varies throughout the carbon fibre, which may suggest that the electrochemical properties also vary throughout the carbon fibre. The knowledge provided by this thesis can lead to future carbon fibre designs with enhanced electrochemical performance for multifunctional applications.
|
|
4. |
- Forsgren, Lilian, 1990
(författare)
-
Processing and properties of thermoplastic composites containing cellulose nanocrystals or wood-based cellulose fibres
- 2020
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Cellulose nanocrystals (CNC) were surface modified with dialkylamines to increase the compatibility between the CNC and the polymeric matrix, and promising results were obtained, with a 300 % stiffness increase when the mixed dispersion was compression moulded on a laboratory scale. The manufacturing process was up-scaled using water-assisted mixing in a twin-screw extruder (TSE) followed by a second compounding step and injection moulding (IM). The composites were successfully produced using conventional melt-processing techniques but these did not show the same improvement in mechanical performance, probably due to the formation of CNC aggregates. There were indications of network formation when CNC was added, especially in the case of surface-modified CNC. Cellulose fibres and thermomechanical pulp were used as reinforcement in similar types of polymer matrices and the mixtures were similarly processed by TSE and IM. These materials were characterized with regard to appearance and durability. The discoloration of the composites due to excessive heat during processing did not significantly affect their mechanical properties, and the addition of the cellulose-based reinforcement to the polymer did not reduce its resistance to thermo-oxidative degradation compared to that of the pure matrix. In fact, the resistance to degradation was increased when lignin was present in the reinforcing element, showing a synergistic effect together with the added anti-oxidant. Superior properties were expected for the CNC composites compared to those of the larger cellulose fibre reinforcements, but in continuous production the stiffening effects were similar regardless of reinforcement type. These results confirm that the processing method and properties strongly affect the final properties of the composite.
|
|
5. |
- Hosseini, Seyedehsan, 1994
(författare)
-
Additive-Driven Improvements in Interfacial Properties and Processing of TMP-Polymer Composites
- 2023
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Efforts to address environmental concerns have resulted in new regulations designed to plan the reduction of plastic and synthetic polymer usage, necessitating the search for sustainable natural alternatives with comparable cost-effectiveness and mechanical performance. Thermomechanical pulp (TMP) fibres are one of the most affordable natural fibres that have no chemical refining in production, production have a high yield of 90-98% and TMP fibres have been demonstrated to improve the mechanical characteristics (strength, stiffness and toughness) of wood-polymer composites (WPCs) compared to the pure polymer. The integration of TMP fibres with non-polar synthetic polymers remains a challenge due to surface polarity differences. This PhD thesis aims to ease the processing of TMP fibre composites through the incorporation of additives. The hypothesis posits that incorporating magnesium stearate (MgSt), molybdenum disulfide (MoS2) and alkyl ketene dimer (AKD) as additives in TMP composites will enhance interfacial properties, resulting in improved processability and flow behaviour at high temperatures. MoS2 is known for its interaction with lignin, which exists in TMP and MgSt is recognised for its ability to improve flow in pharmaceutical processing when combined with cellulose, also a component of TMP. AKD modifies the hydrophilic properties of lignocellulosic surfaces. The experimental work explores the effect of these additives on the properties of TMP composites of ethylene acrylic acid copolymer (EAA) and polypropylene (PP) matrices. The dynamic mechanical analysis (DMA) and mechanical analysis results reveal that MoS2 exhibits superior interaction with TMP fibres, yielding enhanced interfacial properties compared to MgSt in between EAA and TMP fibres. Rheological studies elucidate the transition from a fluid-like state to a network-like structure upon the incorporation of TMP into the PP matrix. The incorporation of AKD with C18 reduces the viscosity of TMP-PP composites and PP itself, and, as determined through theoretical Hansen solubility parameter (HSP) calculations, increases compatibility between cellulose in TMP fibres and PP. The addition of AKD influences both the colour (lighter) and shape (smoother surface) of the extrudate filaments in the TMP-PP composites, indicative of improved processing. In addition, frictional analysis demonstrates the reduction of the coefficient of friction (COF) between metal and TMP fibre by MgSt and AKD treatments.
|
|
6. |
- Liu, Jun, et al.
(författare)
-
Investigation of using limestone calcined clay cement (LC3) in engineered cementitious composites: The effect of propylene fibers and the curing system
- 2021
-
Ingår i: Journal of Materials Research and Technology. - : Elsevier BV. - 2238-7854. ; 15, s. 2117-2144
-
Tidskriftsartikel (refereegranskat)abstract
- Limestone calcined clay cement (LC3) is a new type of low-carbon cement that can reduce energy consumption and carbon dioxide emissions while meeting the performance requirements of ordinary cement. In this study, polypropylene (PP) fibers were mixed into limestone calcined clay cement-based materials to make new low-carbon ECCs. In this study, a total of 24 sets of specimens were designed for 4 groups of curing ages and 6 types of mix ratios. The compressive load–displacement data were measured the compressive curve characteristics were analyzed then, a compressive constitutive model of the composites was deduced and obtained. Through XRD, SEM-EDS and MIP experiments, the reasons and laws of the compressive strength ranges of adding PP fibers and LC3 to engineered cementitious composites (LC3-PP-ECCs) are further explained from the perspective of the pore size, microstructures and hydration products. The results show that, after 28 days, the compressive strength values of LC3-PP-ECCs generally decreases with increasing PP fiber content and the combined effect of PP fibers and hydration products causes the compressive strength of LC3-ECCs with 0.5% PP fibers to drop sharply. In addition, the specimens showed better properties in terms of toughness, ductility and energy absorption. However, in the microstructures, the addition of PP fibers will cause more internal defects and flaws. This results of this study can provide some theoretical experience and technical support for the engineering application of LC3-ECCs.
|
|
7. |
- Zhang, Y., et al.
(författare)
-
MDS study on tensile properties of defective graphene sheet
- 2021
-
Ingår i: 2021 23rd European Microelectronics and Packaging Conference and Exhibition, EMPC 2021.
-
Konferensbidrag (refereegranskat)abstract
- Low-dimensional materials such as graphene exhibit superior electrical, mechanical and thermal properties. However, structural defects occur during the growth or treatment process of carbon nanomaterial and greatly affect the material properties. In this paper, molecular dynamics simulation methods are used to study the effects of atomic defects in graphene sheets on the tensile strength, and the vacancy type and defect orientation are considered in the cases of graphene sheets under various mechanical loadings. The simulation results show that for the graphene sheets with structural defects, the fracture starts near the original vacancy position. The tensile strength of the graphene sheets with X1-type vacancy defects under zigzag direction is reduced by about 26.9% compared with that of the defect-free graphene sheet, while the graphene sheet with X2-type vacancy defects shows the least decrease in magnitude, which is 9.5% lower than that of the perfect graphene sheet. When stretched in the armchair direction, the tensile strength of the graphene sheet with H2 vacancy defects was greatly reduced by 27.1%, and the X1 vacancy defects shows the least influence, where tensile strength of the graphene sheets was reduced by 11.2%.
|
|
8. |
- Rajendra Babu Kalai Arasi, Azega, 1995, et al.
(författare)
-
Influence of Hardwood Lignin Blending on the Electrical and Mechanical Properties of Cellulose Based Carbon Fibers
- 2024
-
Ingår i: ACS Sustainable Chemistry & Engineering. - : American Chemical Society. - 2168-0485. ; 12:30, s. 11206-11217
-
Tidskriftsartikel (refereegranskat)abstract
- Carbon fibers (CFs) are fabricated by blending hardwood kraft lignin (HKL) and cellulose. Various compositions of HKL and cellulose in blended solutions are air-gap spun in 1-ethyl-3-methylimidazolium acetate (EMIM OAc), resulting in the production of virtually bead-free quality fibers. The synthesized HKL-cellulose fibers are thermostabilized and carbonized to achieve CFs, and consequently their electrical and mechanical properties are evaluated. Remarkably, fibers with the highest lignin content (65%) exhibited an electrical conductivity of approximately 42 S/cm, surpassing that of cellulose (approximately 15 S/cm). Moreover, the same fibers demonstrated significantly improved tensile strength (∼312 MPa), showcasing a 5-fold increase compared to pure cellulose while maintaining lower stiffness. Comprehensive analyses, including Auger electron spectroscopy and wide-angle X-ray scattering, show a heterogeneous skin-core morphology in the fibers revealing a higher degree of preferred orientation of carbon components in the skin compared to the core. The incorporation of lignin in CFs leads to increased graphitization, enhanced tensile strength, and a unique skin-core structure, where the skin’s graphitized cellulose and lignin contribute stiffness, while the predominantly lignin-rich core enhances carbon content, electrical conductivity, and strength.
|
|
9. |
- Townsend, Philip, 1991, et al.
(författare)
-
Stochastic modelling of 3D fiber structures imaged with X-ray microtomography
- 2021
-
Ingår i: Computational materials science. - : Elsevier B.V.. - 0927-0256 .- 1879-0801. ; 194
-
Tidskriftsartikel (refereegranskat)abstract
- Many products incorporate into their design fibrous material with particular levels of permeability as a way to control the retention and flow of liquid. The production and experimental testing of these materials can be expensive and time consuming, particularly if it needs to be optimised to a desired level of absorbency. We consider a parametric virtual fiber model as a replacement for the real material to facilitate studying the relationship between structure and properties in a cheaper and more convenient manner. 3D image data sets of a sample fibrous material are obtained using X-ray microtomography and the individual fibers isolated. The segmented fibers are used to estimate the parameters of a 3D stochastic model for generating softcore virtual fiber structures. We use several spatial measures to show the consistency between the real and virtual structures, and demonstrate with lattice Boltzmann simulations that our virtual structure has good agreement with respect to the permeability of the physical material. © 2021 The Author(s)
|
|
10. |
- Hosseini, Seyedehsan, 1994, et al.
(författare)
-
Alkyl ketene dimer modification of thermomechanical pulp promotes processability with polypropylene
- 2024
-
Ingår i: Polymer Composites. - 1548-0569 .- 0272-8397. ; 45:1, s. 825-835
-
Tidskriftsartikel (refereegranskat)abstract
- Alkyl ketene dimers (AKDs) are known to efficiently react with cellulose with a dual polarity in their structure: a polar component and a nonpolar component. AKD of three different carbon chain lengths, 4, 10, and 16 carbons have been synthesized, and thermomechanical pulp (TMP) fibers were modified by them. The modification of TMP fibers with AKD resulted in an increased water contact angle, showing the presence of the AKDs on the TMP fibers and a new carbonyl peak in the IR spectra, suggesting modification of the TMP fibers with AKD groups. Calculating the Hansen solubility parameters of AKD and AKD conjugated to TMP in polypropylene (PP) indicates improved compatibility, especially of longer chain AKD and TMP AKD. The rheological studies of the composites showed that the AKD with the longest carbon chain decreases the melt viscosity of the PP-TMP-AKD composite, which combined with the shape and the color of the extruded composite filaments indicates improved flow properties and reduced stress build up during processing. The research findings demonstrate the ability of AKD to enhance the dispersibility and compatibility of natural fibers with PP.
|
|