Sökning: L4X0:1403 8099 >
New methods for eva...
New methods for evaluation of tissue creping and the importance of coating, paper and adhesion
-
- Boudreau, Jonna, 1980- (författare)
- Karlstads universitet,Institutionen för ingenjörs- och kemivetenskaper (from 2013)
-
- Barbier, Christophe, Associate Professor (preses)
- Karlstads universitet,Institutionen för ingenjörs- och kemivetenskaper (from 2013)
-
- Germgård, Ulf, Professor (preses)
- Karlstads universitet,Institutionen för ingenjörs- och kemivetenskaper (from 2013)
-
visa fler...
-
Albertsson, Sverker (preses)
-
- Pelton, Robert, Professor (opponent)
- McMaster University, Canada
-
visa färre...
-
(creator_code:org_t)
- ISBN 9789170635250
- Karlstad : Karlstads universitet, 2013
- Engelska 60 s.
-
Serie: Karlstad University Studies, 1403-8099 ; 2013:47
-
Serie: Karlstad University Studies, 1403-8099
- Relaterad länk:
-
https://kau.diva-por... (primary) (Raw object)
-
visa fler...
-
https://urn.kb.se/re...
-
visa färre...
Abstract
Ämnesord
Stäng
- The creping process and the conditions on the Yankee cylinder dryer are key factors in a tissue paper mill, and they therefore need to be kept under good control in order to maintain a high and uniform quality. To this end it would be valuable to be able to make on-line measurements of Yankee coating thickness as well as the crepe structure of the tissue paper. The adhesion of paper to the cylinder affects the creping process and more information about the parameters that affect the adhesion is therefore of interest. To perform trials on a full scale or in a pilot plant is very costly and laboratory creping equipment is therefore sought after in order to be able to measure the adhesion force.The coating layer for use on the cylinder was analysed. It contained a large amount of carbohydrates and could not be considered transparent. The thickness of the coating layer was measured on a laboratory cylinder with a method based on fluorescence. An optical brightener was added to the coating chemicals and the coating layer was subjected to UV-radiation. The intensity of the light emitted by the optical brightener was measured and gave an indication of the thickness of the coating layer. The equipment has to be further investigated before it is possible to implement the new sensor on-line.New creping equipment and an adhesion method were developed for use on a laboratory scale. The equipment can operate with different creping angles and the force needed to crepe the paper can be measured. The highest creping force was obtained for papers of high grammage, low dryness at adhesion, high drainability, high fines content and high hemicellulose content.A more direct method is to analyse the structure of the produced paper. Measurements were made on a tissue paper with an optical fibre sensor while the paper was travelling at low speed. The collected signal was mathematically analysed and the characteristic wavelength was calculated for different paper samples. These values were close to the wavelengths measured with an off line method by a commercial crepe analyser.
- BaksidestextThe creping process is the heart of tissue paper manufacture. To control the process better, on-line measurements of paper structure and coating thickness are sought after. The creping is highly dependent on the adhesion of the paper to the Yankee dryer. To be able to measure the adhesion, laboratory creping equipment was also required. Different pulp parameters affect the adhesion and some of them have been investigated in this work.The coating on the Yankee cylinder consisted mainly of fiber fragments and could not be considered as transparent, which had to be considered when choosing a method to measure coating thickness. A method based on the light emitted from an optical brightener in the coating when subjected to UV-irradiation was used, but has to be further improved before it can be used on-line.A new laboratory creping method was developed to determine the adhesion between paper and metal, and the force needed to scrape off the paper with a doctor blade was measured. The highest creping force was obtained for papers made of pulp with a high drainability, high fines content and high hemicellulose content.An optical method using reflected light to measure crepe wavelength on-line was developed. The paper travelled under a sensor and the light collected was mathematically analyzed to determine the most common wavelength.
Ämnesord
- TEKNIK OCH TEKNOLOGIER -- Materialteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering (hsv//eng)
Nyckelord
- tissue
- creping
- paper adhesion
- Tissue paper
- creping
- paper adhesion
- coating layer
- adhesives
- Yankee cylinder
- crepe structure
- wavelength measurements
- Chemical Engineering
- Kemiteknik
Publikations- och innehållstyp
- vet (ämneskategori)
- dok (ämneskategori)
Hitta via bibliotek
Till lärosätets databas