Churning losses and efficiency in gearboxes

↓ Direkt till sidans innehåll
↓ Direkt till sidans sekundära innehåll (sidomenyn)

Sökning: WFRF:(Björklund Stefan) > Churning losses and...

Andersson, MartinKTH,Tribologi (författare)

Churning losses and efficiency in gearboxes

BokEngelska2014

Förlag, utgivningsår, omfång ...

Stockholm :KTH Royal Institute of Technology,2014
22 s.
electronicrdacarrier

Nummerbeteckningar

LIBRIS-ID:oai:DiVA.org:kth-152914
ISBN:9789175952772
https://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-152914URI

Kompletterande språkuppgifter

Språk:engelska
Sammanfattning på:engelska

Ingår i deldatabas

SwePubSwePub

Klassifikation

Ämneskategori:vet swepub-contenttype
Ämneskategori:lic swepub-publicationtype

Anmärkningar

QC 20141006
Efficient transmissions systems are key to producing competitive motor vehicles that have a smaller environmental impact. Gears are the main components in vehicle transmissions and although they are already highly efficient, there is still room for improvement. In this study, the focus falls on the lubricant used to create separating films between gears and todissipate heat. When driving, the gears churn this lubricant, giving rise to power losses that are related to the amount and properties of the lubricant. However, any attempt to reduce these losses must not compromise the required lubrication and heat dissipation. Paper A reports on the use of an FZG gear test rig to investigate power losses and heat generation for different gear immersion depths, surface roughness and coatings. The results show that lower gear roughness reduces gear mesh losses and heat generation. A polishing affect was obtained when a non-coated gear ran against a coated gear.The aim of the research reported in paper B was to increase the accuracy of efficiency testing. It investigated how and whether repeated disassembly and re-assembly of the same test equipment, as well as test performance and rig conditions, affect the measured torque loss in an FZG gear test rig. It was shown that the measured torque loss changes between one assembly and another. Repeatability between tests is crucial for accurate conclusions.The aim of the research reported in paper C was to study whether gear efficiency could be increased by a running-in procedure, which would reduce the need for a coolant. A back-to-back gear test rig was used to test two running-in loads. Higher gear mesh efficiency was seen when a higher running-in load was used.

Ämnesord och genrebeteckningar

TEKNIK OCH TEKNOLOGIER Maskinteknik Tribologi hsv//swe
ENGINEERING AND TECHNOLOGY Mechanical Engineering Tribology hsv//eng
gears
efficiency
temperature
running-in
assembly
torque loss
surface roughness

Biuppslag (personer, institutioner, konferenser, titlar ...)

Olofsson, Ulf,1962-KTH,Tribologi(Swepub:kth)u10qpddv (preses)
Björklund, StefanKTH,Maskinelement(Swepub:kth)u1n6li3l (preses)
Sellgren, UlfKTH,Maskinelement(Swepub:kth)u1r6tcj4 (preses)
Alfredsson, Bo,1962-KTH,Hållfasthetslära(Swepub:kth)u14o1b7w (opponent)
KTHTribologi (creator_code:org_t)

Internetlänk

Hitta via bibliotek

Churning losses and efficiency in gearboxes (Sök publikationen i LIBRIS)

Till lärosätets databas

Hitta mer i SwePub

Av författaren/redakt...: Andersson, Marti ...; Olofsson, Ulf, 1 ...; Björklund, Stefa ...; Sellgren, Ulf; Alfredsson, Bo, ...

Om ämnet

TEKNIK OCH TEKNOLOGIER: TEKNIK OCH TEKNO ...; och Maskinteknik; och Tribologi

Av lärosätet: Kungliga Tekniska Högskolan

Sök utanför SwePub

Sök vidare i:: Google; Google Book Search; Google Scholar

Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.

LIBRIS.kb.se