SwePub
Sök i LIBRIS databas

  Utökad sökning

AMNE:(ENGINEERING AND TECHNOLOGY Civil Engineering)
 

Sökning: AMNE:(ENGINEERING AND TECHNOLOGY Civil Engineering) > Application of Meas...

Application of Measurement While Drilling Technology to Predict Rock Mass Quality and Rock Support for Tunnelling

van Eldert, Jeroen, 1987- (författare)
Luleå tekniska universitet,Geoteknologi
Schunnesson, Håkan (författare)
Luleå tekniska universitet,Geoteknologi
Johansson, Daniel (författare)
Luleå tekniska universitet,Geoteknologi
visa fler...
Saiang, David (författare)
Luleå tekniska universitet,Geoteknologi
visa färre...
 (creator_code:org_t)
2019-10-09
2020
Engelska.
Ingår i: Rock Mechanics and Rock Engineering. - : Springer. - 0723-2632 .- 1434-453X. ; 53:3, s. 1349-1358
  • Tidskriftsartikel (refereegranskat)
Abstract Ämnesord
Stäng  
  • A tunnelling project is normally initiated with a site investigation to determine the in situ rock mass conditions and to generate the basis for the tunnel design and rock support. However, since site investigations often are based on limited information (surface mapping, geophysical profiles, few bore holes, etc.), the estimation of the rock mass conditions may contain inaccuracies, resulting in underestimating the required rock support. The study hypothesised that these inaccuracies could be reduced using Measurement While Drilling (MWD) technology to assist in the decision-making process. A case study of two tunnels in the Stockholm bypass found the rock mass quality was severely overestimated by the site investigation; more than 45% of the investigated sections had a lower rock mass quality than expected. MWD data were recorded in 25 m grout holes and 6 m blast holes. The MWD data were normalised so that the long grout holes with larger hole diameters and the shorter blast holes with smaller hole diameters gave similar results. With normalised MWD data, it was possible to mimic the tunnel contour mapping; results showed good correlation with mapped Q-value and installed rock support. MWD technology can improve the accuracy of forecasting the rock mass ahead of the face. It can bridge the information gap between the early, somewhat uncertain geotechnical site investigation and the geological mapping done after excavation to optimise rock support.

Ämnesord

TEKNIK OCH TEKNOLOGIER  -- Naturresursteknik -- Mineral- och gruvteknik (hsv//swe)
ENGINEERING AND TECHNOLOGY  -- Environmental Engineering -- Mineral and Mine Engineering (hsv//eng)
TEKNIK OCH TEKNOLOGIER  -- Samhällsbyggnadsteknik -- Infrastrukturteknik (hsv//swe)
ENGINEERING AND TECHNOLOGY  -- Civil Engineering -- Infrastructure Engineering (hsv//eng)
TEKNIK OCH TEKNOLOGIER  -- Samhällsbyggnadsteknik -- Byggproduktion (hsv//swe)
ENGINEERING AND TECHNOLOGY  -- Civil Engineering -- Construction Management (hsv//eng)
TEKNIK OCH TEKNOLOGIER  -- Samhällsbyggnadsteknik -- Geoteknik (hsv//swe)
ENGINEERING AND TECHNOLOGY  -- Civil Engineering -- Geotechnical Engineering (hsv//eng)
TEKNIK OCH TEKNOLOGIER  -- Samhällsbyggnadsteknik -- Annan samhällsbyggnadsteknik (hsv//swe)
ENGINEERING AND TECHNOLOGY  -- Civil Engineering -- Other Civil Engineering (hsv//eng)

Nyckelord

Measurement while drilling (MWD)
Rock mass investigation
Tunnelling
Rock mass quality
Rock support
Drill and blast technology
Mining and Rock Engineering
Gruv- och berganläggningsteknik

Publikations- och innehållstyp

ref (ämneskategori)
art (ämneskategori)

Hitta via bibliotek

Till lärosätets databas

Sök utanför SwePub

Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.

 
pil uppåt Stäng

Kopiera och spara länken för att återkomma till aktuell vy