Effect of Ce Addition on the Tribological Behavior of ZK60 Mg-Alloy

↓ Direkt till sidans innehåll
↓ Direkt till sidans sekundära innehåll (sidomenyn)

Sökning: WFRF:(Banijamali M) > Effect of Ce Additi...

Banijamali, S. M.Faculty of Mechanical Engineering, K. N. Toosi University of Technology, Tehran, Iran (författare)

Effect of Ce Addition on the Tribological Behavior of ZK60 Mg-Alloy

Artikel/kapitelEngelska2021

Förlag, utgivningsår, omfång ...

2020-08-06
Springer,2021
printrdacarrier

Nummerbeteckningar

LIBRIS-ID:oai:DiVA.org:ltu-80627
https://urn.kb.se/resolve?urn=urn:nbn:se:ltu:diva-80627URI
https://doi.org/10.1007/s12540-020-00832-4DOI

Kompletterande språkuppgifter

Språk:engelska
Sammanfattning på:engelska

Ingår i deldatabas

SwePubSwePub

Klassifikation

Ämneskategori:ref swepub-contenttype
Ämneskategori:art swepub-publicationtype

Anmärkningar

Validerad;2021;Nivå 2;2021-08-11 (alebob)
The present work aims to study the tribological behavior of an extruded ZK60 alloy in the presence of Ce; in a previous study, among ZK60 alloys with different Ce addition rates, an alloy with 3 wt% of Ce was found to exhibit the most promising mechanical (e.g., hardness and strengths) properties, while its wear behavior remained unknown. The results of microstructural examinations by optical and electron microscopes show that Ce addition reduces the grain size from 6.1 to 2.0 μm. Besides, in addition to the precipitates already distributed in the base alloy (Mg7Zn3), Ce could promote the formation of a new precipitate (MgZn2Ce), increasing the total fraction of the precipitates. These microstructural evolutions enhance the strengths of the studied ZK60 alloy, as the yield and tensile strengths increase from 212 to 308 MPa and from 297 to 354 MPa, respectively. A pin on disc tribometer was employed to study the wear behavior of the developed alloy under different normal loads (5, 20, 40, and 60 N). The results show that the base and Ce-added alloys exhibit almost a similar frictional behavior, while the wear resistance of the Ce-added alloy is higher within the load ranges applied: (i) in low load conditions (5 and 20 N), where the abrasive wear is the active mechanism, the precipitates in the Ce-added alloy could enhance the wear resistance. (ii) Under the load of 40 N, oxidative wear is also an operative wear mechanism, leading to a sharp increase in the wear rate of the alloys. In this condition, Ce could provide a protective oxide layer, which could improve the wear resistance of the alloy. (iii) At a load of 60 N, both studied alloys exhibit a similar wear rate due to a severe oxidation condition. Therefore, beyond this loading condition, the microstructural evolutions (e.g., change in precipitation behavior) caused by Ce addition can no longer contribute to the enhancement of wear resistance.

Ämnesord och genrebeteckningar

TEKNIK OCH TEKNOLOGIER Maskinteknik Tribologi hsv//swe
ENGINEERING AND TECHNOLOGY Mechanical Engineering Tribology hsv//eng
ZK60 magnesium alloy
Ce addition
pin on disc
abrasive wear
Maskinelement
Machine Elements
Materialteknik
Engineering Materials

Biuppslag (personer, institutioner, konferenser, titlar ...)

Palizdar, Y.Department of Nano-technology and Advanced Materials, Materials & Energy Research Center (MERC), Karaj, Iran (författare)
Najafi, S.School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran, Iran (författare)
Sheikhani, A.School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran, Iran (författare)
Nezhad, M. Soltan AliDepartment of Nano-technology and Advanced Materials, Materials & Energy Research Center (MERC), Karaj, Iran (författare)
Moghaddam, Pouria ValizadehLuleå tekniska universitet,Maskinelement(Swepub:ltu)pouval (författare)
Torkamani, HadiLuleå tekniska universitet,Materialvetenskap(Swepub:ltu)hadtor (författare)
Faculty of Mechanical Engineering, K. N. Toosi University of Technology, Tehran, IranDepartment of Nano-technology and Advanced Materials, Materials & Energy Research Center (MERC), Karaj, Iran (creator_code:org_t)

Sammanhörande titlar

Ingår i:Metals and Materials International: Springer27:8, s. 2732-27421598-96232005-4149

Internetlänk

Hitta via bibliotek

Metals and Materials International (Sök värdpublikationen i LIBRIS)

Till lärosätets databas

Hitta mer i SwePub

Av författaren/redakt...: Banijamali, S. M ...; Palizdar, Y.; Najafi, S.; Sheikhani, A.; Nezhad, M. Solta ...; Moghaddam, Pouri ...; visa fler...; Torkamani, Hadi; visa färre...

Om ämnet

TEKNIK OCH TEKNOLOGIER: TEKNIK OCH TEKNO ...; och Maskinteknik; och Tribologi

Artiklar i publikationen: Metals and Mater ...

Av lärosätet: Luleå tekniska universitet

Sök utanför SwePub

Sök vidare i:: Google; Google Book Search; Google Scholar

Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.

LIBRIS.kb.se