Sökning: WFRF:(Dahlin T.)
> (2020-2023) >
The use of asymmetr...
The use of asymmetric time constraints in 4-D ERT inversion
-
- Loke, M. H. (författare)
- Geotomo Software, Malaysia
-
- Wilkinson, P. B. (författare)
- British Geological Survey
-
- Chambers, J. E. (författare)
- British Geological Survey
-
visa fler...
-
- Uhlemann, S. (författare)
- British Geological Survey,Lawrence Berkeley National Laboratory
-
- Dijkstra, T. (författare)
- Loughborough University
-
- Dahlin, T. (författare)
- Lund University,Lunds universitet,Teknisk geologi,Institutionen för biomedicinsk teknik,Institutioner vid LTH,Lunds Tekniska Högskola,Engineering Geology,Department of Biomedical Engineering,Departments at LTH,Faculty of Engineering, LTH
-
visa färre...
-
(creator_code:org_t)
- Elsevier BV, 2022
- 2022
- Engelska.
-
Ingår i: Journal of Applied Geophysics. - : Elsevier BV. - 0926-9851. ; 197
- Relaterad länk:
-
http://dx.doi.org/10...
-
visa fler...
-
https://lup.lub.lu.s...
-
https://doi.org/10.1...
-
visa färre...
Abstract
Ämnesord
Stäng
- Time-lapse resistivity surveys are commonly used to monitor temporal changes in the subsurface. In certain cases, it is known from other information that the resistivity will only decrease or increase with time. The 4-D resistivity smoothness-constrained inversion method reduces artifacts due to noise by including a temporal roughness filter constraint that ensures the temporal changes vary in a smooth manner. A least-squares optimization method is used to find a solution by attempting to locate the minimum of an objective function that consists of the data misfit and model (spatial and temporal) roughness. In some cases, the 4-D time-lapse inverse models show an increase in the resistivity with time in parts of the subsurface where it is only expected to decrease (or vice versa). We compare two methods, the barrier function and transformation methods, that attempt to minimize or eliminate these artifacts. We incorporate the barrier function constraint into the 4-D inverse method by using a modified difference matrix as a temporal roughness filter. The barrier function constraint includes an additional term that increases the objective function value greatly if the model values cross the allowed thresholds. This greatly minimizes the artifacts but does not completely eliminate them. It has the advantage that there are minimal changes in the objective function in regions of model space that are not close to the imposed thresholds. The method of transformations changes the model parameter such that the additional positivity or negativity constraints are implicitly included in the transformed model parameter. It has the advantage that it can completely eliminate the artifacts. However, it modifies the entire objective function which could be a disadvantage in some cases. We also explore a combination of the two methods, using the barrier function method to generate an initial model that minimizes the artifacts followed by the transformation method. This hybrid technique completely removes the residual artifacts left by the barrier method, and produces an inverse model which is closer to the true model for a synthetic data set. We also describe a post-inversion modification of the L-curve method to determine the optimum model that takes into account the non-linear nature of the inverse problem and the forward modelling method. The technique gave an estimate of the noise level for a field data set and produced a model which is consistent with independent hydrological measurements at the test site.
Ämnesord
- NATURVETENSKAP -- Geovetenskap och miljövetenskap -- Geofysik (hsv//swe)
- NATURAL SCIENCES -- Earth and Related Environmental Sciences -- Geophysics (hsv//eng)
Nyckelord
- 4-D
- Asymmetric
- Constraints
- Inversion
- Resistivity
- Time
Publikations- och innehållstyp
- art (ämneskategori)
- ref (ämneskategori)
Hitta via bibliotek
Till lärosätets databas