Search: L773:0022 0434 OR L773:1528 9028 >
Proportional–Integr...
Proportional–Integral Controller Design for Combustion-Timing Feedback, from n-Heptane to iso-Octane in Compression-Ignition Engines
-
- Ingesson, Gabriel (author)
- Lund University,Lunds universitet,Institutionen för reglerteknik,Institutioner vid LTH,Lunds Tekniska Högskola,Department of Automatic Control,Departments at LTH,Faculty of Engineering, LTH
-
- Yin, Lianhao (author)
- Lund University,Lunds universitet,Förbränningsmotorer,Institutionen för energivetenskaper,Institutioner vid LTH,Lunds Tekniska Högskola,Combustion Engines,Department of Energy Sciences,Departments at LTH,Faculty of Engineering, LTH
-
- Johansson, Rolf (author)
- Lund University,Lunds universitet,Institutionen för reglerteknik,Institutioner vid LTH,Lunds Tekniska Högskola,Department of Automatic Control,Departments at LTH,Faculty of Engineering, LTH
-
show more...
-
- Tunestål, Per (author)
- Lund University,Lunds universitet,Förbränningsprocesser KCFP,Annan verksamhet, LTH,Lunds Tekniska Högskola,Förbränningsmotorer,Institutionen för energivetenskaper,Institutioner vid LTH,The Competence Centre for Combustion Processes,Other operations, LTH,Faculty of Engineering, LTH,Combustion Engines,Department of Energy Sciences,Departments at LTH,Faculty of Engineering, LTH
-
show less...
-
(creator_code:org_t)
- 2017-12-19
- 2017
- English.
-
In: Journal of Dynamic Systems, Measurement, and Control, ASME. - : ASME International. - 0022-0434 .- 1528-9028.
- Related links:
-
http://dx.doi.org/10...
-
show more...
-
https://lup.lub.lu.s...
-
https://doi.org/10.1...
-
show less...
Abstract
Subject headings
Close
- The problem of designing robust and noise-insensitive PI controllers for pressure-sensor based combustion-timing control was studied through simulation. Different primary reference fuels (PRF) and operating conditions were studied. The simulations were done using a physics-based, control-oriented model with an empirical ignition-delay correlation. It was found that the controllable region, in-between the zero-gain region for early injection timings and the misfire region for late injection timings is strongly PRF dependent. As a result, it was necessary to adjust intake temperature to compensate for the difference in fuel reactivity prior to the controller design. With adjusted intake temperature, PRF dependent negative-temperature coefficient behavior gave different system characteristics for the different fuels. The PI-controller design was accomplished by solving the optimization problem of maximizing disturbance rejection and tracking performance subject to constraints on robustness and measurement-noise sensitivity. Optimal controller gains were found to be limited by the high system gain at late combustion timings and high-load conditions, furthermore, the measurement-noise sensitivity was found to be higher at the low-load operating points where the ignition delay is more sensitive to variations in load and intake-conditions. The controller-gain restrictions were found to vary for the different PRFs, the optimal gains for higher PRFs were lower due to a higher system gain, whereas the measurement-noise sensitivity was found to be higher for lower PRFs.
- The problem of designing robust and noise-insensitive PI controllers for pressure-sensor based combustion-timing control was studied through simulation. Different primary reference fuels (PRF) and operating conditions were studied. The simulations were done using a physics-based, control-oriented model with an empirical ignition-delay correlation. It was found that the controllable region, in-between the zero-gain region for early injection timings and the misfire region for late injection timings is strongly PRF dependent. As a result, it was necessary to adjust intake temperature to compensate for the difference in fuel reactivity prior to the controller design. With adjusted intake temperature, PRF dependent negative-temperature coefficient behavior gave different system characteristics for the different fuels. The PI-controller design was accomplished by solving the optimization problem of maximizing disturbance rejection and tracking performance subject to constraints on robustness and measurement-noise sensitivity. Optimal controller gains were found to be limited by the high system gain at late combustion timings and high-load conditions, furthermore, the measurement-noise sensitivity was found to be higher at the low-load operating points where the ignition delay is more sensitive to variations in load and intake-conditions. The controller-gain restrictions were found to vary for the different PRFs, the optimal gains for higher PRFs were lower due to a higher system gain, whereas the measurement-noise sensitivity was found to be higher for lower PRFs.
Subject headings
- TEKNIK OCH TEKNOLOGIER -- Elektroteknik och elektronik -- Reglerteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Electrical Engineering, Electronic Engineering, Information Engineering -- Control Engineering (hsv//eng)
Publication and Content Type
- art (subject category)
- ref (subject category)
Find in a library
To the university's database