onr:"swepub:oai:lup.lub.lu.se:f9e18d42-13ff-434c-8bce-180b4e45102d"
Sökning: onr:"swepub:oai:lup.lub.lu.se:f9e18d42-13ff-434c-8bce-180b4e45102d" > Ultrahard boron nit...
- 1 av 1
- Föregående post
- Nästa post
- Till träfflistan
- Melaibari, Ammar A. (författare)
Ultrahard boron nitride material through a hybrid laser/waterjet based surface treatment
- Artikel/kapitelEngelska2016
Förlag, utgivningsår, omfång ...
- Elsevier BV,2016
Nummerbeteckningar
- LIBRIS-ID:oai:lup.lub.lu.se:f9e18d42-13ff-434c-8bce-180b4e45102d
- https://lup.lub.lu.se/record/8560148URI
- https://doi.org/10.1016/j.actamat.2015.08.082DOI
Kompletterande språkuppgifter
- Språk:engelska
- Sammanfattning på:engelska
Ingår i deldatabas
- SwePubSwePub
Klassifikation
Anmärkningar
- We report a dual phase boron nitride (BN) material composed of 50% cubic and 50% wurtzite phases that has the same level of hardness as polycrystalline diamond. The dual phase BN material was initially synthesized from high pressure and high temperature consolidation of powder materials and subsequently, a laser/waterjet heat treatment (LWH) was applied to the material surface. The LWH process consisted of heating the sample surface using a continuous wave CO2 laser beam followed by tandem waterjet quenching of the laser irradiated material. The indentation hardness of the as-synthesized material was measured to be nominally 37 GPa. After the heat treatment the indentation hardness increased to nominal values of 75 GPa reaching the hardness of polycrystalline diamond 65-80 GPa. Dispersive Raman spectroscopy, high-resolution scanning electron microscope (HRSEM) and surface grazing XRD were used to characterize the BN phase signatures, grain size changes and phase transitions in both as-synthesized and heat treated material. Comparison of the as-synthesized and heat treated material microstructure revealed that heat treatment resulted in microstructure that consists of large grains; surrounded with regions of nano-grains between larger grains and; formation of solid interlayer along the grain boundaries. The increase in hardness was observed for LWH processing at laser fluence below 35 J/mm(2), and LWH processing above this value resulted in spallation of BN material from the surface. Raman spectrums of the material processed below the laser fluence of 35 J/mm(2) indicated that there are minimal phase transitions in the material; however, above that fluence, BN transformed into hexagonal phase resulting in surface damage through spallation. A combination of amorphous phase formation at the grain boundaries and grain size refinement are suggested as the mechanisms responsible for the LWH processing induced hardness increase. (C) 2015 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
Ämnesord och genrebeteckningar
- TEKNIK OCH TEKNOLOGIER Materialteknik Metallurgi och metalliska material hsv//swe
- ENGINEERING AND TECHNOLOGY Materials Engineering Metallurgy and Metallic Materials hsv//eng
- Ultrahard material
- Boron Nitide
- Laser heat treatment
- Microstructure
- Composite wBN/cBN
Biuppslag (personer, institutioner, konferenser, titlar ...)
- Zhao, Jingnan (författare)
- Molian, Pal (författare)
- Bushlya, VolodymyrLund University,Lunds universitet,Industriell Produktion,Institutionen för maskinvetenskaper,Institutioner vid LTH,Lunds Tekniska Högskola,Production and Materials Engineering,Department of Mechanical Engineering Sciences,Departments at LTH,Faculty of Engineering, LTH(Swepub:lu)ipro-vob (författare)
- Zhou, JinmingLund University,Lunds universitet,Industriell Produktion,Institutionen för maskinvetenskaper,Institutioner vid LTH,Lunds Tekniska Högskola,Production and Materials Engineering,Department of Mechanical Engineering Sciences,Departments at LTH,Faculty of Engineering, LTH(Swepub:lu)mtov-jzh (författare)
- Ståhl, Jan-EricLund University,Lunds universitet,Industriell Produktion,Institutionen för maskinvetenskaper,Institutioner vid LTH,Lunds Tekniska Högskola,Production and Materials Engineering,Department of Mechanical Engineering Sciences,Departments at LTH,Faculty of Engineering, LTH(Swepub:lu)mtov-jst (författare)
- Petrusha, Igor (författare)
- Shrotriya, Pranav (författare)
- Industriell ProduktionInstitutionen för maskinvetenskaper (creator_code:org_t)
Sammanhörande titlar
- Ingår i:Acta Materialia: Elsevier BV102, s. 315-3221873-24531359-6454
Internetlänk
- 1 av 1
- Föregående post
- Nästa post
- Till träfflistan
Hitta mer i SwePub
- Av författaren/redakt...
- Melaibari, Ammar ...
- Zhao, Jingnan
- Molian, Pal
- Bushlya, Volodym ...
- Zhou, Jinming
- Ståhl, Jan-Eric
- visa fler...
- Petrusha, Igor
- Shrotriya, Prana ...
- visa färre...
- Om ämnet
-
- TEKNIK OCH TEKNOLOGIER
- TEKNIK OCH TEKNO ...
- och Materialteknik
- och Metallurgi och m ...
- Artiklar i publikationen
- Acta Materialia
- Av lärosätet
- Lunds universitet
Sök utanför SwePub
- Sök vidare i:
- Google Book Search
- Google Scholar
Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.
- Copyright © LIBRIS - Nationella bibliotekssystem
- LIBRIS.kb.se
