SwePub
Sök i LIBRIS databas

  Utökad sökning

WFRF:(Rasmuson Anders 1951)
 

Sökning: WFRF:(Rasmuson Anders 1951) > Fluid dynamics simu...

  • Darelius, Anders,1977Chalmers tekniska högskola,Chalmers University of Technology (författare)

Fluid dynamics simulation of the high shear mixing process

  • Artikel/kapitelEngelska2010

Förlag, utgivningsår, omfång ...

  • Elsevier BV,2010

Nummerbeteckningar

  • LIBRIS-ID:oai:research.chalmers.se:e6422323-dba7-492a-aa99-b8de0c67c98f
  • https://doi.org/10.1016/j.cej.2009.12.020DOI
  • https://research.chalmers.se/publication/129324URI

Kompletterande språkuppgifter

  • Språk:engelska
  • Sammanfattning på:engelska

Ingår i deldatabas

Klassifikation

  • Ämneskategori:art swepub-publicationtype
  • Ämneskategori:ref swepub-contenttype

Anmärkningar

  • The Eulerian-Eulerian two-fluid approach for modelling multiphase flows is used to simulate the flow in a high shear mixer. The results are compared with experimental velocity profiles for the solids phase at the wall in the mixer obtained using a high speed camera (Darelius et al. Chem. Eng. Sci. 62 (2007) 2366).The governing equations are closed using relations from the Kinetic Theory of Granular Flow (KTGF) combined with a frictional stress model due to Johnson and Jackson and Schaeffer and inter-phase drag due to Wen and Yu. In addition, calculations are presented for a model with a constant particle phase viscosity (CPV). Free slip and partial slip boundary conditions for the solid phase velocity at the vessel wall and the impeller have been utilized.The results show that the bed height could be well predicted by the partial slip model, whereas the free slip model could not capture the experimentally found bed height satisfactorily. For the KTGF model, the swirling motion of the rotating torus that is formed by the moving powder bed was over-predicted and the tangential wall velocity was under-predicted, probably due to the fact that the frictional stress model needs to be further developed, e.g. to tackle cohesive particles in dense flow. The CPV model gave predictions in good agreement with the experiments for a solids viscosity of 0.1. Pa. s and a wall slip parameter of 0.005. m/Pa. s. However, for a very low or very high value of the particle phase viscosity and for a high value of the wall slip parameter the agreement with experiments was poor. Interestingly, values of the viscosity that are commonly employed for fluidized beds seem applicable also in the present case. © 2009 Elsevier B.V.

Ämnesord och genrebeteckningar

Biuppslag (personer, institutioner, konferenser, titlar ...)

  • Remmelgas, JohanAstraZeneca AB (författare)
  • Rasmuson, Anders,1951Chalmers tekniska högskola,Chalmers University of Technology(Swepub:cth)rasmuson (författare)
  • van Wachem, Berend,1972Imperial College of Science, Technology and Medicine(Swepub:cth)berend (författare)
  • Niklasson Björn, Ingela,1960AstraZeneca AB (författare)
  • Chalmers tekniska högskolaAstraZeneca AB (creator_code:org_t)

Sammanhörande titlar

  • Ingår i:Chemical Engineering Journal: Elsevier BV164:2-3, s. 418-4241385-8947

Internetlänk

Hitta via bibliotek

Till lärosätets databas

Sök utanför SwePub

Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.

 
pil uppåt Stäng

Kopiera och spara länken för att återkomma till aktuell vy