WFRF:(Wretland Anders)
Search: WFRF:(Wretland Anders) > (2021) > High-pressure flank...
- 3 of 3
- Previous record
- Next record
- To hitlist
High-pressure flank cooling and chip morphology in turning Alloy 718
-
- Tamil Alagan, Nageswaran, 1990- (author)
- Högskolan Väst,Forskningsmiljön produktionsteknik(PTW),Avdelningen för avverkande och additativa tillverkningsprocesser (AAT),PTW
-
- Zeman, Pavel (author)
- Department of Production Machines and Equipment (RCMT), Faculty of Mechanical Engineering, Czech Technical University in Prague, Prague (CZE)
-
- Mara, Vladimir (author)
- Department of Material Engineering, Faculty of Mechanical Engineering, Czech Technical University in Prague, Prague, (CZE)
- show more...
- show less...
- (creator_code:org_t)
- Elsevier Ltd, 2021
- 2021
- English.
- In: CIRP - Journal of Manufacturing Science and Technology. - : Elsevier Ltd. - 1755-5817 .- 1878-0016. ; 35, s. 659-674
- Journal article (peer-reviewed)
Abstract
Subject headings
Close
- The use of cutting fluids is commonly considered a necessity while machining Heat Resistant Super Alloys (HRSA). Specifically, cutting fluids applied under high-pressure, which for many decades have been the solution for the most demanding applications. The results might be diverse and vary between applications, but typically leads to improved tool life, enhanced chip breakability, lower temperature in the cutting zone and better surface quality of the finished product. The available high-pressure cutting fluid delivery systems are usually designed with the intention to improve the cutting fluid penetration at the vicinity of the cutting edge on the rake face side of the insert. However, there has been limited interest in investigating high-pressure cutting fluid applied to its flank face. Both specifically and in combination with cutting fluid directed to the rake face. In this study, the focus has been to investigate the chip formation process during the turning of Alloy 718 (Inconel 718). Particularly, for a defined turning operation where high-pressure cutting fluid is applied to the flank side as well as the rake side of an uncoated carbide insert. Several combinations of pressure levels and jet directions were investigated. The corresponding effects on the tool-chip contact zone and chip characteristics were studied for two cutting speeds. The results of the investigation showed a substantial improvement in lowering the tool-chip contact area at a rake pressure of 16 MPa. At which pressure, additional cutting fluid applied to the flank at a moderate pressure of 8 MPa had no dominant effect on chip formation (chip break). However, flank cooling of the cutting zone supports chip segmentation and thus indirectly chip breakability. For cutting fluid applied to the rake side at a more moderate pressure of 8 MPa, more prominent effects on the insert became apparent when additional cutting fluid was applied to the flank side. This was particularly noticeable when cutting fluid was directed towards the flank side of the insert at the same pressure level as the cutting fluid applied towards its rake face. The additional thermal transfer was seen to have a significant effect on the material deformation phenomena in the primary shear zone (lowering shear angle) as well as the sliding and sticking conditions of the tool-chip interface. Based on the evidence from this study, it can be concluded that cutting fluid applied towards the flank side of the insert has a significant impact on the cutting process. In particular, if applied in combination with a rake pressure at a similar level, in this case, 8 MPa. © 2021 The Authors
Subject headings
- TEKNIK OCH TEKNOLOGIER -- Materialteknik -- Bearbetnings-, yt- och fogningsteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering -- Manufacturing, Surface and Joining Technology (hsv//eng)
Keyword
- Carbide cutting tools; Carbides; Cutting; Cutting fluids; Morphology; Shear flow; Thermal management (electronics); Turning
- Chip segmentation; Lower temperatures; Material deformation; Moderate pressures; Tool-chip contact; Tool-chip contact area; Tool-chip interface; Turning operations
- Cutting tools
- Production Technology
- Produktionsteknik
Publication and Content Type
- ref (subject category)
- art (subject category)
Find in a library
- CIRP - Journal of Manufacturing Science and Technology (Search for host publication in LIBRIS)
To the university's database
- 3 of 3
- Previous record
- Next record
- To hitlist
Find more in SwePub
- By the author/editor
- Tamil Alagan, Na ...
- Zeman, Pavel
- Mara, Vladimir
- Beno, Tomas, 196 ...
- Wretland, Anders
- About the subject
-
- ENGINEERING AND TECHNOLOGY
- ENGINEERING AND ...
- and Materials Engine ...
- and Manufacturing Su ...
- Articles in the publication
- CIRP - Journal o ...
- By the university
- University West
Search outside SwePub
- Extend your search to:
- Google Book Search
- Google Scholar
Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.
- Copyright © LIBRIS - National Library Systems
- LIBRIS.kb.se
