AMNE:(ENGINEERING AND TECHNOLOGY Electrical Engineering, Electronic Engineering, Information Engineering Robotics)
Search: AMNE:(ENGINEERING AND TECHNOLOGY Electrical Engineering, Electronic Engineering, Information Engineering Robotics) > (1990-1994) > Task planning for w...
- 8 of 10
- Previous record
- Next record
- To hitlist
Task planning for welding applications
- Bolmsjö, Gunnar (author)
-
- Nikoleris, Giorgos (author)
- Lund University,Lunds universitet,Innovation,Institutionen för designvetenskaper,Institutioner vid LTH,Lunds Tekniska Högskola,ID-A verkstaden,Department of Design Sciences,Departments at LTH,Faculty of Engineering, LTH,ID-A workshop,Faculty of Engineering, LTH
- (creator_code:org_t)
- 1993
- 1993
- English 5 s.
- In: Systems, Man and Cybernetics : Systems Engineering in the Service of Humans - Systems Engineering in the Service of Humans. - 0780309111 ; , s. 515-519
- Conference paper (peer-reviewed)
Abstract
Subject headings
Close
- Welding robots that use sensors to compensate for variations in their environment pose new requirements for programming systems and for controller architectures. Tracking sensors must be programmed with the geometry of the welds and the motions of the robot. The process monitoring system must be programmed with the required process tolerances and the type of weld. Finally, the controller must be programmed with the motion parameters, velocity and end-pose. Task planning for welding applications is the specification of the geometrical and the technological parameters that are necessary to the above subsystems. The architecture of the controller also must be process-related to allow the flow of planning information to the different subsystems and the necessary feedback to the planning level. Data from the sensors must be used with path data, process information and the geometry of the welds to adjust the process in real time. This article describes the requirements of process-related programming and real-time control of industrial robots based on sensor data.
- Welding robots that use sensors to compensate for variations in their environment pose new requirements for programming systems and for controller architectures. Tracking sensors must be programmed with the geometry of the welds and the motions of the robot. The process monitoring system must be programmed with the required process tolerances and the type of weld. Finally, the controller must be programmed with the motion parameters, velocity and end-pose. Task planning for welding applications is the specification of the geometrical and the technological parameters that are necessary to the above subsystems. The architecture of the controller also must be process-related to allow the flow of planning information to the different subsystems and the necessary feedback to the planning level. Data from the sensors must be used with path data, process information and the geometry of the welds to adjust the process in real time. This article describes the requirements of process-related programming and real-time control of industrial robots based on sensor data.
Subject headings
- TEKNIK OCH TEKNOLOGIER -- Elektroteknik och elektronik -- Robotteknik och automation (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Electrical Engineering, Electronic Engineering, Information Engineering -- Robotics (hsv//eng)
Publication and Content Type
- kon (subject category)
- ref (subject category)
Find in a library
- Systems, Man and Cybernetics : Systems Engineering in the Service of Humans - Sy... (Search for host publication in LIBRIS)
To the university's database
- 8 of 10
- Previous record
- Next record
- To hitlist
Find more in SwePub
- By the author/editor
- Bolmsjö, Gunnar
- Nikoleris, Giorg ...
- About the subject
-
- ENGINEERING AND TECHNOLOGY
- ENGINEERING AND ...
- and Electrical Engin ...
- and Robotics
- Articles in the publication
- Systems, Man and ...
- By the university
- Lund University
Search outside SwePub
- Extend your search to:
- Google Book Search
- Google Scholar
Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.
- Copyright © LIBRIS - National Library Systems
- LIBRIS.kb.se
