Sökning: (id:"swepub:oai:DiVA.org:kau-5630") >
Performance of adva...
Performance of advanced tool steels for cutting tool bodies
-
- Medvedeva, Anna, 1981- (författare)
- Karlstads universitet,Avdelningen för maskin- och materialteknik
-
- Bergström, Jens, Professor (preses)
- Karlstads universitet,Fakulteten för teknik- och naturvetenskap
-
- Krakhmalev, Pavel, PhD, Associate professor (preses)
- Karlstads universitet,Fakulteten för teknik- och naturvetenskap
-
visa fler...
-
- Gunnarsson, Staffan, MD (preses)
- Uddeholms AB
-
- Schulze, Volker, Professor, Dr.-Ing. habil. (opponent)
- Karlsruhe Institute of Technology
-
visa färre...
-
(creator_code:org_t)
- ISBN 9789170633072
- Karlstad : Karlstad University, 2010
- Engelska 80 s.
-
Serie: Karlstad University Studies, 1403-8099 ; 2010:17
- Relaterad länk:
-
https://kau.diva-por... (primary) (Raw object)
-
visa fler...
-
https://urn.kb.se/re...
-
visa färre...
Abstract
Ämnesord
Stäng
- Performance of indexable insert cutting tools is not only about the performance of cutting inserts. It is also about the cutting tool body, which has to provide a secure and accurate insert positioning as well as its quick and easy handling under severe working conditions. The common damage mechanisms of cutting tool bodies are fatigue and plastic deformation. Cutting tools undergo high dynamic stresses going in and out cutting engagement; as a result, an adequate level of fatigue strength is the essential steel property. Working temperatures of tool bodies in the insert pocket can reach up to 600°C, why the tool steel requires high softening resistance to avoid plastic deformation. Machinability is also essential, as machining of the steel represents a large fraction of the production cost of a cutting tool. The overall aim of the study is to improve the tool body performance by use of an advanced steel grade with an optimized combination of all the demanding properties. Due to the high-temperature conditions, the thesis concerns mostly hot-work tool steels increasing also the general knowledge of their microstructure, mechanical properties and machinability. Knowing the positive effect of sulphur on machinability of steels, the first step was to indentify a certain limit of the sulphur addition, which would not reduce the fatigue strength of the tool body below an acceptable level. In tool bodies, where the demand on surface roughness was low and a geometrical stress concentrator was present, the addition of sulphur could be up to 0.09 wt%. Fatigue performance of the cutting tools to a large extent depended on the steel resistance to stress relaxation under high dynamic loading and elevated temperatures. The stress relaxation behaviour, material substructure and dislocation characteristics in low-alloyed and hot-work tool steels were studied using X-ray diffraction under thermal and mechanical loading. Different tool steels exhibited different stress relaxation resistance depending on their microstructure, temper resistance and working temperature. Hot-work tool steels showed to be more preferable to low-alloyed tool steels because of their ability to inhibit the rearrangement and annihilation of induced dislocations. High-temperature softening resistance of the hot-work tool steels was investigated during high-temperature hold-times and isothermal fatigue and discussed with respect to their microstructure. Carbide morphology and precipitation were determined using scanning and transmission electron microscopy. Machinability of a prehardened hot-work tool steel of varying nickel content from 1 to 5 wt% was investigated in end milling and drilling operations. Machining the higher nickel containing steels resulted in longer tool life and generated lower cutting forces and tool/workpiece interface temperature. The difference in machinability of the steels was discussed in terms of their microstructure and mechanical properties.
Ämnesord
- TEKNIK OCH TEKNOLOGIER -- Materialteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering (hsv//eng)
Nyckelord
- tool steel
- cutting tool body
- fatigue strength
- stress relaxation
- machinability
- high-temperature properties
- microstructure
- Materials science
- Teknisk materialvetenskap
- Materialteknik
- Materials Engineering
Publikations- och innehållstyp
- vet (ämneskategori)
- dok (ämneskategori)
Hitta via bibliotek
Till lärosätets databas